Home › Engine / Hybrid System › 2TR-FE (ENGINE MECHANICAL) › ENGINE
RM2850E _51 Engine / Hybrid System _073288 2TR-FE ENGINE MECHANICAL _0356950 ENGINE G

2TR-FE ENGINE MECHANICAL  ENGINE  ON-VEHICLE INSPECTION  


PROCEDURE

Hide 17801 4.INSPECT AIR CLEANER FILTER ELEMENT SUB-ASSEMBLY

a.

Remove the air cleaner filter element.


b.

Visually check that there is no dirt, blockages, or damage to the air cleaner filter element.

HINT:
·

If there is any dirt or blockages in the air cleaner filter element, clean it with compressed air.

·

If any dirt or blockages remain even after cleaning the air cleaner filter element with compressed air, replace it.




Hide 6.CHECK VALVE LASH ADJUSTER NOISE

a.

Rev up the engine several times. Check that the engine does not emit unusual noises.


b.

If unusual noises occur, warm up the engine and idle it for over 30 minutes. Then repeat the step above.

HINT:

If any defects or problems are found during the inspection above, perform a lash adjuster inspection (see page Engine / Hybrid System>2TR-FE (ENGINE MECHANICAL)>CAMSHAFT>INSPECTION ).



Hide 7.INSPECT IGNITION TIMING

a.

Warm up the engine and stop the engine.


b.

When using an intelligent tester:

i.
A158501E06
1.729,0.135 1.01,0.854 true 2.125,2.021 1.875,1.615 false 2.167,1.969 2.573,2.125 0.406,0.156 10 true DLC3 1.729,0.042 2.781,0.208 1.052,0.167 10 false Intelligent Tester

Connect the intelligent tester to the DLC3.


ii.

Turn the ignition switch ON and turn the intelligent tester ON.


iii.

Select the following menu items: Powertrain / Engine and ECT / Data List / IGN Advance.

Standard ignition timing:

0 to 20 degrees BTDC


HINT:

Refer to the intelligent tester operator's manual for further details.



iv.

Inspect the ignition timing during idling.



c.

When not using the intelligent tester:

i.
A118802E16
0.906,1.667 0.49,1.885 true 0.198,1.823 0.5,2.073 0.302,0.25 10 false TAC 0.104,0.073 0.594,0.448 0.49,0.375 12 false DLC3:

Using SST, connect the tachometer probe to terminal 9 (TAC) of the DLC3.

SST
09843-18030  

NOTICE:
·

Confirm the terminal numbers before connecting them. Connection with a wrong terminal can damage the engine.

·

Turn off all electrical systems before connecting the terminals.




ii.
A156749E02
1.844,0.958 2.042,1.333 true 1.75,1.344 3.208,1.573 1.458,0.229 10 true Green-red Lead Wire

Clamp the tester probe of a timing light to the 4 lead wires or green-red lead wire of the ignition coil connector for the No. 1 cylinder.

NOTICE:

Use a timing light that detects the first signal.



iii.

Start the engine.


iv.
A156782E02
1.531,1.063 1.313,0.542 true 1.813,1.479 2.208,0.531 true 0.104,2.26 0.573,2.625 0.469,0.365 10 false Engine Speed 0.854,2.573 2.979,2.823 2.125,0.25 10 false Approximately 1000 to 1500 rpm 2.396,3.156 3.271,3.417 0.875,0.26 10 false Idling Speed 1.406,3.302 1.917,3.51 0.51,0.208 10 false 5 sec. 1.052,4.219 3.042,4.51 1.99,0.292 10 false Connect Terminals TC and CG 1.073,0.406 1.313,0.552 0.24,0.146 10 false CG 2.229,0.396 2.438,0.542 0.208,0.146 10 false TC 0.063,0.063 0.573,0.25 0.51,0.188 12 false DLC3:

Using SST, connect terminals 13 (TC) and 4 (CG) of the DLC3.

SST
09843-18040  

NOTICE:

Examine the terminal numbers before connecting them. Connecting the wrong terminals can damage the engine.


HINT:
·

After connecting the terminals (TC and CG), the engine rpm increases to between 1000 and 1500 rpm for 5 seconds, then returns to idling speed. This is because the ECM checks that the ISC (idling speed control system) operates properly.

·

Perform the inspection of the ignition timing after the engine rpm has returned to idling speed.




v.
A156746

Using a timing light, measure the ignition timing during idling.

Standard ignition timing:

3 to 7 degrees BTDC


NOTICE:
·

Turn all electrical systems and the A/C off.

·

When checking the ignition timing, shift the transmission to the neutral position.




vi.

Remove SST from terminals 13 (TC) and 4 (CG) of the DLC3.


vii.

Check the ignition timing during idling.

Standard ignition timing:

0 to 20 degrees BTDC



viii.

Confirm that ignition timing moves to the advanced angle side when the engine speed is increased.


ix.

Remove the timing light.



Hide 8.INSPECT ENGINE IDLING SPEED

a.

Warm up and stop the engine.


b.
A158501E07
1.729,0.135 1.01,0.854 true 2.146,2.073 1.865,1.635 false 2.188,2 2.594,2.156 0.406,0.156 10 true DLC3 1.781,0.042 2.833,0.208 1.052,0.167 10 false Intelligent Tester

When using an intelligent tester:

i.

Connect the intelligent tester to the DLC3.

HINT:

Refer to the intelligent tester operator's manual for further details.



ii.

Turn the ignition switch ON and turn the intelligent tester ON.


iii.

Select the following menu items: Powertrain / Engine and ECT / Data List / Engine Speed.

Standard idle speed:

750 to 850 rpm


NOTICE:
·

Turn all electrical systems and the A/C off.

·

When checking the ignition timing, shift the transmission to the neutral position.





c.
A118802E16
0.906,1.667 0.49,1.885 true 0.198,1.823 0.5,2.073 0.302,0.25 10 false TAC 0.104,0.073 0.594,0.448 0.49,0.375 12 false DLC3:

When not using the intelligent tester:

Check the idling speed.

i.

Using SST, connect tachometer tester probe to terminal 9 (TAC) of the DLC3.

SST
09843-18030  


ii.

Start the engine at idle.


iii.

Check the idling speed.

Standard idling speed:

750 to 850 rpm




Hide 9.INSPECT COMPRESSION

a.

Warm up and stop the engine.


b.

Disconnect the injector connectors.


c.

d.

Remove the spark plugs.


e.
A156748

Check the cylinder compression pressure.

i.

Insert a compression gauge into the spark plug hole.


ii.

Fully open the throttle.


iii.

While cranking the engine, measure the compression pressure.

Standard compression pressure:

1230 kPa (12.5 kgf/cm2, 178 psi)


Minimum pressure:

880 kPa (9.0 kgf/cm2, 128 psi)


Difference between each cylinder:

98 kPa (1.0 kgf/cm2, 14 psi)


NOTICE:
·

Always use a fully charged battery to obtain an engine speed of 250 rpm or more.

·

Check the other cylinders' compression pressure in the same way.

·

This measurement must be done as quickly as possible.



If the cylinder compression is low, pour a small amount of engine oil into the cylinder through the spark plug hole and inspect again.

HINT:
·

If adding oil increases the compression, the piston rings and/or cylinder bore may be worn or damaged.

·

If the pressure stays low, the valve may be stuck or seated improperly, or there may be a leak in the gasket.





f.

Install the spark plugs.

Torque:

18 N*m (184 kgf*cm, 13 ft.*lbf)




h.

Connect the injection connectors.


Hide 10.CHECK CO/HC

a.

Start and warm up the engine.


b.

Run the engine at 2500 rpm for approximately 180 seconds and idle the engine.


c.
A156747E02
2.875,0.875 2.875,0.677 false 2.427,0.51 3.323,0.719 0.896,0.208 10 true CO/HC Meter

Insert CO/HC meter testing probe at least 40 cm (1.3 ft.) into the tailpipe.


d.

Check CO/HC concentration at idle.

Idle CO concentration:

0 to 0.5%


Idle HC concentration:

Applicable local regulation



e.

If the CO/HC concentration is not as specified, perform troubleshooting in the order given below.

i.

Check the heated oxygen sensor operation.

Click hereEngine / Hybrid System>2TR-FE (ENGINE CONTROL)>HEATED OXYGEN SENSOR>INSPECTION


ii.

See the table below for possible causes, and then inspect and repair the applicable parts if necessary.

CO HC Problems Causes
Normal High Rough idle
1.

Faulty ignitions:

-

Incorrect timing

-

Plugs are contaminated, shorted or gaps are defective


2.

Incorrect valve clearance

3.

Leaks in intake and exhaust valves

4.

Leaks in cylinders


Low High Rough idle
(Fluctuating HC reading)
1.

Vacuum leaks:

-

Ventilation hoses

-

Intake manifold

-

Throttle body

-

Brake booster line


2.

Lean mixture causing misfire


High High Rough idle
(Black smoke from exhaust)
1.

Restricted air filter

2.

Plugged ventilation valve

3.

Faulty SFI system:

-

Faulty pressure regulator

-

Defective Engine Coolant Temperature sensor

-

Defective Mass Air Flow (MAF) meter

-

Faulty ECM

-

Faulty injectors

-

Faulty throttle position sensor