Home › Engine / Hybrid System › 2TR-FE (ENGINE CONTROL) › SFI SYSTEM
RM2850E _51 Engine / Hybrid System _073287 2TR-FE ENGINE CONTROL _0357042 SFI SYSTEM C

2TR-FE ENGINE CONTROL  SFI SYSTEM  P0037  Oxygen Sensor Heater Control Circuit Low (Bank 1 Sensor 2)  P0038  Oxygen Sensor Heater Control Circuit High (Bank 1 Sensor 2)  


DESCRIPTION

Refer to DTC P0136 (Click here Engine / Hybrid System>2TR-FE (ENGINE CONTROL)>SFI SYSTEM>P0136).

HINT:
·

Sensor 1 refers to the sensor mounted before the Three-Way Catalytic Converter (TWC) and is located near the engine assembly.

·

Sensor 2 refers to the sensor mounted after the TWC and is located far from the engine assembly.



A430087E01
0.146,0.104 2.083,0.292 1.938,0.188 10 false Reference (System Diagram): 0.198,1.333 0.729,1.677 0.531,0.344 10 false from P/I Fuse 1.104,1.49 1.771,1.667 0.667,0.177 10 false EFI MAIN 2.229,2.823 3.49,3.042 1.26,0.219 10 false from ECM (MREL) 2.01,2.365 2.323,2.542 0.313,0.177 10 false EFI 3.135,2.365 4.635,2.563 1.5,0.198 10 false Heated Oxygen Sensor 5.875,2.958 6.323,3.177 0.448,0.219 10 false ECM 5.063,1.729 5.521,1.917 0.458,0.188 10 false OX1B 5.073,2.479 5.354,2.656 0.281,0.177 10 false E2 5.063,1.219 5.521,1.406 0.458,0.188 10 false HT1B 3.938,1.229 4.365,1.417 0.427,0.188 10 false HT1B 3.938,1.719 4.365,1.906 0.427,0.188 10 false OX1B 3.563,2.042 4.083,2.229 0.521,0.188 10 false Sensor 3.563,1.49 4.052,1.667 0.49,0.177 10 false Heater 3.292,1.729 3.531,1.917 0.24,0.188 10 false E2 3.281,1.208 3.521,1.396 0.24,0.188 10 false +B

DTC No. DTC Detection Condition Trouble Area
P0037 Heated current is 0.3 A or less when heater operates
(1 trip detection logic)
·

Open in heater circuit of heated oxygen sensor

·

Heated oxygen sensor heater

·

EFI relay

·

ECM


P0038 Heated current exceeds 2 A when heater operates
(1 trip detection logic)
·

Short in heater circuit of heated oxygen sensor

·

Heated oxygen sensor heater

·

EFI relay

·

ECM



MONITOR DESCRIPTION

The sensing portion of the heated oxygen sensor has a zirconia element which is used to detect oxygen concentration in the exhaust. If the zirconia element is at the proper temperature and the difference of the oxygen concentration between the inside and outside surface of the sensor is large, the zirconia element will generate voltage signals. In order to increase the oxygen concentration detecting capacity in the zirconia element, the ECM supplements the heat from the exhaust with the heat from the heating element inside the sensor. When current in the sensor is out of the standard operating range, the ECM interprets this as a fault in the heated oxygen sensor and stores a DTC.

Example:

The ECM will store a high-current DTC if the current in the sensor is more than 2 A when the heater is OFF. Similarly, the ECM will store a low-current DTC if the current is less than 0.3 A when the heater is ON.

WIRING DIAGRAM

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following inspection procedure.


HINT:
·

Read freeze frame data using the GTS. Freeze frame data records the engine conditions when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air-fuel ratio was lean or rich, and other data from the time the malfunction occurred.

·

Sensor 1 refers to the sensor closest to the engine assembly.

·

Sensor 2 refers to the sensor farthest away from the engine assembly.

·

Change the fuel injection volume using the Control the Injection Volume function provided in the Active Test and monitor the heated oxygen sensor output voltage (Click here Engine / Hybrid System>2TR-FE (ENGINE CONTROL)>SFI SYSTEM>DATA LIST / ACTIVE TEST). If the sensor output voltage does not change (almost no reaction) while performing the Active Test, the sensor may be malfunctioning.



PROCEDURE

1.INSPECT HEATED OXYGEN SENSOR (HEATER RESISTANCE)

Result:
Proceed to
OK
NG



OK

2.CHECK TERMINAL VOLTAGE (+B OF HEATED OXYGEN SENSOR)

NG

2.CHECK TERMINAL VOLTAGE (+B OF HEATED OXYGEN SENSOR)
a.
A149595E48
0.375,1.729 0.792,2 0.417,0.271 1.969,1.781 2.333,1.49 true 0.115,0.094 0.375,0.323 0.26,0.229 10 false *a 0.448,1.771 0.781,1.969 0.333,0.198 10 false A62 2.365,1.385 2.667,1.573 0.302,0.188 10 false +B

Disconnect the heated oxygen sensor connector.


b.

Turn the ignition switch to ON.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
A62-2 (+B) - Body ground Ignition switch ON 11 to 14 V


Text in Illustration
*a Front view of wire harness connector
(to Heated Oxygen Sensor)


Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (HEATED OXYGEN SENSOR - ECM)

NG

5.INSPECT NO. 2 INTEGRATION RELAY (EFI RELAY)
3.CHECK HARNESS AND CONNECTOR (HEATED OXYGEN SENSOR - ECM)
a.

Disconnect the heated oxygen sensor connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A62-1 (HT1B) - B73-2 (HT1B) Always Below 1 Ω
A62-1 (HT1B) or B73-2 (HT1B) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

4.CHECK WHETHER DTC OUTPUT RECURS

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK WHETHER DTC OUTPUT RECURS
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.



e.

Turn the ignition switch off and wait for at least 30 seconds.


f.

Start the engine and idle it for 5 minutes or more.


g.

With the vehicle stationary, depress the accelerator pedal and maintain an engine speed of 3000 rpm for 1 minute.


h.

Idle the engine for 5 minutes or more.


i.

Read the output pending DTCs using the GTS.


Result:
Result Proceed to
No pending DTC is output A
Pending DTC P0037, P0038 is output B



A

B

5.INSPECT NO. 2 INTEGRATION RELAY (EFI RELAY)
a.

Inspect the NO. 2 integration relay (EFI relay) (Click here Engine / Hybrid System>2TR-FE (ENGINE CONTROL)>RELAY>ON-VEHICLE INSPECTION).


Result:
Proceed to
OK
NG



OK

6.CHECK HARNESS AND CONNECTOR (HEATED OXYGEN SENSOR - NO. 2 INTEGRATION RELAY)

NG

REPLACE NO. 2 INTEGRATION RELAY

6.CHECK HARNESS AND CONNECTOR (HEATED OXYGEN SENSOR - NO. 2 INTEGRATION RELAY)
a.

Disconnect the heated oxygen sensor connector.


b.

Remove the NO. 2 integration relay from the NO. 2 relay block and junction block assembly.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A62-2 (+B) - 2D-4 Always Below 1 Ω
A62-2 (+B) or 2D-4 - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR