Home › Engine / Hybrid System › 2TR-FE (ENGINE CONTROL) › SFI SYSTEM
RM2850E _51 Engine / Hybrid System _073287 2TR-FE ENGINE CONTROL _0357042 SFI SYSTEM J

2TR-FE ENGINE CONTROL  SFI SYSTEM  Starter Signal Circuit  


DESCRIPTION

When the engine is cranked, the intake air flow becomes slow, so fuel vaporization is poor. A rich mixture is therefore necessary in order to achieve good startability. While the engine is being cranked, the battery voltage is applied to terminal STA of the ECM. The starter signal is mainly used to increase the fuel injection volume for starting and after-start injection control.

WIRING DIAGRAM

A401739E01
1.24,1.094 1.552,1.292 0.313,0.198 10 false 12 1.49,1.094 1.854,1.323 0.365,0.229 10 false AM2 2.104,1.094 2.469,1.292 0.365,0.198 10 false ST2 2.469,1.083 2.781,1.281 0.313,0.198 10 false 9 1.417,1.542 1.729,1.74 0.313,0.198 10 false J63 1.406,1.75 2.5,1.969 1.094,0.219 10 false Ignition Switch 3.49,1.385 4.208,1.583 0.719,0.198 10 false ST NO. 2 5.396,3.344 5.708,3.542 0.313,0.198 10 false 12 5.688,3.354 6.063,3.573 0.375,0.219 10 false STA 5.927,4.698 6.24,4.896 0.313,0.198 10 false A55 3.198,3.813 3.417,4.01 0.219,0.198 10 false 1 2.552,3.823 2.802,4.021 0.25,0.198 10 false 5 2.302,4.313 2.635,4.531 0.333,0.219 10 false ST 2.552,4.76 2.865,4.958 0.313,0.198 10 false 3 3.208,4.76 3.417,4.958 0.208,0.198 10 false 2 1.656,3.677 2.354,3.865 0.698,0.188 10 false ST NO. 1 0.729,3.677 1.583,3.896 0.854,0.219 10 false R/B NO. 2-B 0.552,4.563 1.24,4.771 0.688,0.208 10 false FL MAIN 1.344,5.625 1.656,5.823 0.313,0.198 10 false C9 1.385,5.427 1.698,5.625 0.313,0.198 10 false 1 1.844,5.198 2.063,5.396 0.219,0.198 10 false 1 2.031,5.229 2.344,5.427 0.313,0.198 10 false B12 2.271,5.438 2.583,5.635 0.313,0.198 10 false ST 1.667,5.49 1.979,5.688 0.313,0.198 10 false B 1.375,6.427 2.552,6.656 1.177,0.229 10 false Starter assembly 0.729,6.531 1.281,6.792 0.552,0.26 10 false Battery 0.573,2.167 1.031,2.396 0.458,0.229 10 false AM2 0.573,2.865 1.042,3.083 0.469,0.219 10 false J/B-B 6.313,4.688 6.677,4.938 0.365,0.25 10 false ECM

CAUTION / NOTICE / HINT

NOTICE:
·

Inspect the fuses for circuits related to this system before performing the following procedure.

·

After turning ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work (Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).



PROCEDURE

1.CHECK WHETHER ENGINE CAN BE CRANKED
a.

Check if the engine can be cranked.


Result:
Result Proceed to
Engine cannot be cranked A
Engine can be cranked B



A

2.READ VALUE USING GTS

B

11.READ VALUE USING GTS (STARTER SIGNAL)
2.READ VALUE USING GTS
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine and ECT / Data List / Starter Signal.


e.

Check the value displayed on the GTS when the ignition switch is turned to the ON and START positions.

OK:
Switch Position Starter Signal
ON OFF
START ON



Result:
Proceed to
OK
NG



OK

6.INSPECT ST RELAY

NG

3.CHECK HARNESS AND CONNECTOR (IGNITION SWITCH ASSEMBLY - ST RELAY - ECM)
3.CHECK HARNESS AND CONNECTOR (IGNITION SWITCH ASSEMBLY - ST RELAY - ECM)
a.

Disconnect the ignition switch assembly connector.


b.

Remove the ST relay from the NO. 2 relay block and junction block assembly.


c.

Disconnect the ECM connector.


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
J63-9 (ST2) - ST relay terminal 1 Always Below 1 Ω
J63-9 (ST2) - A55-12 (STA) Always Below 1 Ω
J63-9 (ST2), ST relay terminal 1 or A55-12 (STA) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

4.INSPECT IGNITION SWITCH

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.INSPECT IGNITION SWITCH
a.

Result:
Proceed to
OK
NG



OK

5.CHECK HARNESS AND CONNECTOR (BATTERY - IGNITION SWITCH)

NG

REPLACE IGNITION SWITCH ASSEMBLY

5.CHECK HARNESS AND CONNECTOR (BATTERY - IGNITION SWITCH)
a.

Disconnect the cable from the negative (-) battery terminal.


b.

Disconnect the cable from the positive (+) battery terminal.


c.

Disconnect the ignition switch assembly connector.


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
Positive (+) battery terminal - J63-12 (AM2) Always Below 1 Ω
Positive (+) battery terminal or J63-12 (AM2) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

6.INSPECT ST RELAY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.INSPECT ST RELAY

Result:
Proceed to
OK
NG



OK

7.INSPECT STARTER ASSEMBLY

NG

REPLACE ST RELAY

7.INSPECT STARTER ASSEMBLY
a.

Inspect the starter assembly (Click hereEngine / Hybrid System>2TR-FE STARTING>STARTER>INSPECTION).


Result:
Proceed to
OK
NG



OK

8.CHECK HARNESS AND CONNECTOR (ST RELAY - STARTER ASSEMBLY)

NG

REPLACE STARTER ASSEMBLY

8.CHECK HARNESS AND CONNECTOR (ST RELAY - STARTER ASSEMBLY)
a.

Remove the ST relay from the NO. 2 relay block and junction block assembly.


b.

Disconnect the starter assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
ST relay terminal 3 - B12-1 (ST) Always Below 1 Ω
ST relay terminal 3 or B12-1 (ST) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

9.CHECK HARNESS AND CONNECTOR (BATTERY - STARTER ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

9.CHECK HARNESS AND CONNECTOR (BATTERY - STARTER ASSEMBLY)
a.

Disconnect the cable from the negative (-) battery terminal.


b.

Disconnect the cable from the positive (+) battery terminal.


c.

Disconnect the starter assembly connector.


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
Positive (+) battery terminal - C9-1 (B) Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

10.CHECK HARNESS AND CONNECTOR (BATTERY - ST RELAY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

10.CHECK HARNESS AND CONNECTOR (BATTERY - ST RELAY)
a.

Disconnect the cable from the negative (-) battery terminal.


b.

Disconnect the cable from the positive (+) battery terminal.


c.

Remove the ST relay from the NO. 2 relay block and junction block assembly.


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
Positive (+) battery terminal - ST relay terminal 5 Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

CHECK HARNESS AND CONNECTOR (ST RELAY - BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

11.READ VALUE USING GTS (STARTER SIGNAL)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine and ECT / Data List / Starter Signal.


e.

Check the value displayed on the GTS when the ignition switch is turned to the ON and START positions.

OK:
Switch Position Starter Signal
ON OFF
START ON



Result:
Proceed to
OK
NG



OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

12.CHECK HARNESS AND CONNECTOR (IGNITION SWITCH ASSEMBLY - ST RELAY - ECM)
12.CHECK HARNESS AND CONNECTOR (IGNITION SWITCH ASSEMBLY - ST RELAY - ECM)
a.

Disconnect the ignition switch assembly connector.


b.

Remove the ST relay from the NO. 2 relay block and junction block assembly.


c.

Disconnect the ECM connector.


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
J63-9 (ST2) - A55-12 (STA) Always Below 1 Ω
ST relay terminal 1 - A55-12 (STA) Always Below 1 Ω
J63-9 (ST2), ST relay terminal 1 or A55-12 (STA) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR