Home › Engine / Hybrid System › N04C-VL (ENGINE CONTROL) › ECD SYSTEM
RM2850E _51 Engine / Hybrid System _073159 N04C-VL ENGINE CONTROL _0357053 ECD SYSTEM J

N04C-VL ENGINE CONTROL  ECD SYSTEM  VC Output Circuit  


DESCRIPTION

The ECM constantly uses 5 V from the battery voltages supplied to the +B (BATT) terminal to operate the microprocessor. The ECM also provides this power to the sensors through the VC output circuit.

When the VC circuit is short-circuited, the microprocessor in the ECM and sensors that obtain power through the VC circuit are deactivated because power is not supplied from the VC circuit. Under this condition, the system does not start up and the MIL is not illuminated even if the system malfunctions.

HINT:

Under normal conditions, the MIL is illuminated for several seconds when the ignition switch is first turned to ON. The MIL goes off when the engine is started.


A225144E06
4.896,0.49 5.229,0.656 0.333,0.167 10 false ECM 4.427,1.177 6.198,1.427 1.771,0.25 10 false 5 V Constant Voltage Circuit 5.375,1.948 6.375,2.281 1,0.333 10 false Microprocessor 2.948,0.917 3.344,1.083 0.396,0.167 10 false BATT 3.042,1.281 3.24,1.448 0.198,0.167 10 false +B 3.167,2.188 3.385,2.354 0.219,0.167 10 false VC 4.073,3.125 4.188,3.292 0.115,0.167 10 false R 1.167,1 2.563,1.438 1.396,0.438 10 false No. 2 integration relay from EFI-MAIN Fuse 1.167,1.469 2.531,2.083 1.365,0.615 10 false No. 2 integration relay from EFI NO. 2 Fuse 0.354,2.052 2.646,2.719 2.292,0.667 10 false Throttle Position Sensor, Accelerator Pedal Position Sensor, etc. (Sensors which have IC) 0.354,3.031 2.688,3.458 2.333,0.427 10 false Engine Coolant Temperature Sensor, Intake Air Temperature Sensor, etc.

WIRING DIAGRAM

A402323E01
5.802,0.271 6.115,0.469 0.313,0.198 10 false 5 5.771,1.115 6.083,1.313 0.313,0.198 10 false 13 5.802,1.646 6.115,1.844 0.313,0.198 10 false 3 5.771,3.156 6.083,3.354 0.313,0.198 10 false 13 5.771,3.646 6.083,3.844 0.313,0.198 10 false 14 5.802,4.146 6.115,4.344 0.313,0.198 10 false 2 5.76,4.646 6.073,4.844 0.313,0.198 10 false 16 4.146,4.719 4.458,4.917 0.313,0.198 10 false 2 4.146,4.219 4.458,4.417 0.313,0.198 10 false 5 4.146,3.719 4.458,3.917 0.313,0.198 10 false 4 4.146,3.219 4.458,3.417 0.313,0.198 10 false 6 4.125,1.719 4.438,1.917 0.313,0.198 10 false 3 4.135,0.344 4.448,0.542 0.313,0.198 10 false 2 2.302,0.208 2.615,0.406 0.313,0.198 10 false 1 2.302,0.479 2.615,0.677 0.313,0.198 10 false 3 2.313,1.604 2.625,1.802 0.313,0.198 10 false 2 2.302,1.854 2.615,2.052 0.313,0.198 10 false 1 2.302,4.344 2.615,4.542 0.313,0.198 10 false 3 2.292,4.885 2.604,5.083 0.313,0.198 10 false 1 5.76,5.958 6.073,6.156 0.313,0.198 10 false 14 5.76,6.51 6.073,6.708 0.313,0.198 10 false 15 5.76,7.021 6.073,7.219 0.313,0.198 10 false 13 5.76,7.531 6.073,7.729 0.313,0.198 10 false 14 2.313,6.594 2.625,6.792 0.313,0.198 10 false 3 2.313,7.094 2.625,7.292 0.313,0.198 10 false 1 2.323,7.604 2.635,7.802 0.313,0.198 10 false 2 5.677,0.448 6.292,0.646 0.615,0.198 10 false B104 5.688,1.302 6.302,1.5 0.615,0.198 10 false B104 5.677,1.823 6.292,2.021 0.615,0.198 10 false B104 5.688,3.333 6.302,3.531 0.615,0.198 10 false B105 5.698,3.823 6.313,4.021 0.615,0.198 10 false B105 5.698,4.323 6.313,4.521 0.615,0.198 10 false B105 5.688,4.813 6.302,5.01 0.615,0.198 10 false B105 5.688,6.135 6.302,6.333 0.615,0.198 10 false B104 5.688,6.688 6.302,6.885 0.615,0.198 10 false B103 5.698,7.198 6.313,7.396 0.615,0.198 10 false B103 5.688,7.698 6.302,7.896 0.615,0.198 10 false B103 2.229,0.854 2.688,1.052 0.458,0.198 10 false B18 2.24,2.219 2.698,2.417 0.458,0.198 10 false B27 2.438,5.281 2.896,5.479 0.458,0.198 10 false B93 0.781,8.104 1.24,8.302 0.458,0.198 10 false k2 2.219,1.031 4.521,1.229 2.302,0.198 10 false Manifold Absolute Pressure Sensor 2.25,2.417 4.354,2.833 2.104,0.417 10 false Throttle Position Sensor (Built into Diesel Throttle Body Assembly) 2.438,5.469 4.229,5.833 1.792,0.365 10 false Fuel Pressure Sensor (Built into Common Rail Assembly) 0.781,8.281 2.5,8.479 1.719,0.198 10 false Camshaft Position Sensor 2.51,0.323 3.125,0.521 0.615,0.198 10 false E 2.51,0.594 3.125,0.792 0.615,0.198 10 false VC 3.771,0.448 4.385,0.646 0.615,0.198 10 false PIM 2.51,1.698 3.125,1.896 0.615,0.198 10 false E2 2.51,1.969 3.125,2.167 0.615,0.198 10 false VC 3.75,1.823 4.365,2.021 0.615,0.198 10 false VTA 6.146,0.448 6.76,0.646 0.615,0.198 10 false PIM 6.146,1.313 6.76,1.51 0.615,0.198 10 false VC 6.135,1.833 6.75,2.031 0.615,0.198 10 false VLU 6.146,3.333 6.76,3.531 0.615,0.198 10 false VC2 6.135,3.823 6.75,4.021 0.615,0.198 10 false E21 6.146,4.313 6.76,4.51 0.615,0.198 10 false PCR2 6.146,4.823 6.76,5.021 0.615,0.198 10 false PCR1 3.75,3.333 4.365,3.531 0.615,0.198 10 false VC2 3.844,3.823 4.458,4.021 0.615,0.198 10 false E2 3.667,4.323 4.281,4.521 0.615,0.198 10 false PCR2 3.667,4.813 4.281,5.01 0.615,0.198 10 false PCR1 2.5,4.979 3.115,5.177 0.615,0.198 10 false VC1 2.51,4.458 3.125,4.656 0.615,0.198 10 false E1 1.979,6.688 2.594,6.885 0.615,0.198 10 false VG 2,7.188 2.615,7.385 0.615,0.198 10 false G1 2.021,7.698 2.635,7.896 0.615,0.198 10 false G- 6.156,6.135 6.771,6.333 0.615,0.198 10 false E2 6.146,6.688 6.76,6.885 0.615,0.198 10 false VCG 6.146,7.198 6.76,7.396 0.615,0.198 10 false G+ 6.146,7.708 6.76,7.906 0.615,0.198 10 false G- 6.344,8.354 6.802,8.552 0.458,0.198 10 false ECM

A402324E01
1.833,0.552 1.99,0.75 0.156,0.198 10 false 4 1.833,1.052 1.99,1.25 0.156,0.198 10 false 5 1.844,1.583 2,1.781 0.156,0.198 10 false 3 1.833,2.094 1.99,2.292 0.156,0.198 10 false 1 1.844,2.594 2,2.792 0.156,0.198 10 false 2 5.302,0.49 5.458,0.688 0.156,0.198 10 false 6 5.313,1 5.469,1.198 0.156,0.198 10 false 2 5.313,1.51 5.469,1.708 0.156,0.198 10 false 5 5.302,2.01 5.458,2.208 0.156,0.198 10 false 1 5.302,2.521 5.458,2.719 0.156,0.198 10 false 3 5.229,0.667 5.688,0.865 0.458,0.198 10 false A56 5.24,1.177 5.698,1.375 0.458,0.198 10 false A57 5.229,1.688 5.688,1.885 0.458,0.198 10 false A56 5.229,2.188 5.688,2.385 0.458,0.198 10 false A57 5.229,2.698 5.688,2.896 0.458,0.198 10 false A56 1.313,0.667 1.927,0.865 0.615,0.198 10 false VCPA 5.646,0.667 6.26,0.865 0.615,0.198 10 false VCPA 1.417,1.188 2.031,1.385 0.615,0.198 10 false VPA 1.417,1.677 2.031,1.875 0.615,0.198 10 false EPA 1.354,2.188 1.969,2.385 0.615,0.198 10 false VPA2 1.354,2.688 1.969,2.885 0.615,0.198 10 false EPA2 5.656,1.188 6.271,1.385 0.615,0.198 10 false VPA 5.656,1.698 6.271,1.896 0.615,0.198 10 false EPA 5.667,2.198 6.281,2.396 0.615,0.198 10 false VPA2 5.656,2.698 6.271,2.896 0.615,0.198 10 false EPA2 6.031,3.313 6.49,3.51 0.458,0.198 10 false ECM 0.104,2.958 0.417,3.156 0.313,0.198 10 false F9 0.083,3.156 2.417,3.573 2.333,0.417 10 false Accelerator Pedal Position Sensor (Built into Accelerator Link Assembly)

CAUTION / NOTICE / HINT

NOTICE:

After replacing the ECM, the new ECM needs registration (Click hereEngine / Hybrid System>N04C-VL (ENGINE CONTROL)>ECD SYSTEM>REGISTRATION) and initialization (Click hereEngine / Hybrid System>N04C-VL (ENGINE CONTROL)>ECD SYSTEM>INITIALIZATION).


PROCEDURE

1.CHECK MIL
a.

Check that the Malfunction Indicator Lamp (MIL) illuminates when turning the ignition switch to ON.

OK:

MIL lights up.



Result:
Proceed to
OK
NG



OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

2.CHECK CONNECTION BETWEEN GTS AND ECM
2.CHECK CONNECTION BETWEEN GTS AND ECM
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Check the communication between the GTS and ECM.


Result:
Result Proceed to
Communication is not possible A
Communication is possible B



A

3.CHECK DIESEL THROTTLE BODY ASSEMBLY (CHECK MIL ILLUMINATED)

B

3.CHECK DIESEL THROTTLE BODY ASSEMBLY (CHECK MIL ILLUMINATED)
a.

Disconnect the throttle position sensor connector.


b.

Turn the ignition switch to ON.


c.

Check the MIL.


Result:
Result Proceed to
MIL does not illuminate A
MIL illuminates B



A

4.CHECK ACCELERATOR LINK ASSEMBLY (CHECK MIL ILLUMINATED)

B

4.CHECK ACCELERATOR LINK ASSEMBLY (CHECK MIL ILLUMINATED)
a.

Disconnect the accelerator pedal position sensor connector.


b.

Turn the ignition switch to ON.


c.

Check the MIL.


Result:
Result Proceed to
MIL does not illuminate A
MIL illuminates B



A

5.CHECK CAMSHAFT POSITION SENSOR (CHECK MIL ILLUMINATED)

B

5.CHECK CAMSHAFT POSITION SENSOR (CHECK MIL ILLUMINATED)
a.

Disconnect the camshaft position sensor connector.


b.

Turn the ignition switch to ON.


c.

Check the MIL.


Result:
Result Proceed to
MIL does not illuminate A
MIL illuminates B



A

6.CHECK MANIFOLD ABSOLUTE PRESSURE SENSOR (CHECK MIL ILLUMINATED)

B

6.CHECK MANIFOLD ABSOLUTE PRESSURE SENSOR (CHECK MIL ILLUMINATED)
a.

Disconnect the manifold absolute pressure sensor connector.


b.

Turn the ignition switch to ON.


c.

Check the MIL.


Result:
Result Proceed to
MIL does not illuminate A
MIL illuminates B



A

7.CHECK COMMON RAIL ASSEMBLY (CHECK MIL ILLUMINATED)

B

7.CHECK COMMON RAIL ASSEMBLY (CHECK MIL ILLUMINATED)
a.

Disconnect the fuel pressure sensor connector.


b.

Turn the ignition switch to ON.


c.

Check the MIL.


Result:
Result Proceed to
MIL does not illuminate A
MIL illuminates B



A

8.CHECK HARNESS AND CONNECTOR

B

REPLACE COMMON RAIL ASSEMBLY

8.CHECK HARNESS AND CONNECTOR
a.

Disconnect the throttle position sensor connector.


b.

Disconnect the accelerator pedal position sensor connector.


c.

Disconnect the camshaft position sensor connector.


d.

Disconnect the manifold absolute pressure sensor connector.


e.

Disconnect the fuel pressure sensor connector.


f.

Disconnect the ECM connectors.


g.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
B104-13 (VC) - Body ground Always 10 kΩ or higher
B105-13 (VC2) - Body ground Always 10 kΩ or higher
B103-15 (VCG) - Body ground Always 10 kΩ or higher
A56-6 (VCPA) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR