Home › Vehicle Interior › METER / GAUGE / DISPLAY › METER / GAUGE SYSTEM › 2017.01–2021.01
RM2850E _58 Vehicle Interior _073141 METER / GAUGE / DISPLAY _0357098 METER / GAUGE SYSTEM J

METER / GAUGE / DISPLAY  METER / GAUGE SYSTEM  Tachometer Malfunction  


DESCRIPTION

w/ Multi-information Display:

The combination meter assembly receives engine speed signals from the ECM via the CAN communication line. The combination meter assembly displays the engine speed calculated based on the data received from the ECM.


w/o Multi-information Display:

The combination meter assembly controls the tachometer in accordance with engine speed signals from the ECM (except 1HZ) or pickup sensor (for 1HZ).


WIRING DIAGRAM

w/ Multi-information Display:


E402224E04
0.75,3.333 4.417,3.531 3.667,0.198 10 false : CAN Communication Line 1.688,2.49 2.135,2.688 0.448,0.198 10 false ECM 4.479,2.49 6.333,2.719 1.854,0.229 10 false Combination Meter Assembly


w/o Multi-information Display:


E368465E01
1.813,0.813 2.427,1.01 0.615,0.198 10 false TAC 1.313,1.438 1.927,1.635 0.615,0.198 10 false A54*1 5.042,0.823 5.656,1.021 0.615,0.198 10 false S 2.802,0.938 3.417,1.135 0.615,0.198 10 false *1 2.24,0.719 2.854,0.917 0.615,0.198 10 false 6 4.802,0.729 5.417,0.927 0.615,0.198 10 false 5 4.771,1.385 5.385,1.583 0.615,0.198 10 false J1 4.76,1.563 6.875,1.792 2.115,0.229 10 false Combination Meter Assembly 5.052,2.5 5.667,2.698 0.615,0.198 10 false TACH 4.802,2.406 5.417,2.604 0.615,0.198 10 false 1 4.271,2.625 4.885,2.823 0.615,0.198 10 false *3 2.813,2.625 3.427,2.823 0.615,0.198 10 false *2 2.24,2.406 2.854,2.604 0.615,0.198 10 false 18 1.802,2.5 2.417,2.698 0.615,0.198 10 false TAC 1.333,3.115 1.948,3.313 0.615,0.198 10 false A57*2 2.24,4.083 2.854,4.281 0.615,0.198 10 false 4 2.823,4.281 3.438,4.479 0.615,0.198 10 false *4 1.885,4.188 2.5,4.385 0.615,0.198 10 false IG4 4.271,4.292 4.885,4.49 0.615,0.198 10 false *5 4.823,4.083 5.438,4.281 0.615,0.198 10 false 1 5.052,4.177 5.667,4.375 0.615,0.198 10 false NE+ 5.948,4.167 6.563,4.365 0.615,0.198 10 false NE- 6.333,4.083 6.948,4.281 0.615,0.198 10 false 2 5.146,4.646 5.76,4.844 0.615,0.198 10 false B23*5 5.448,3.115 6.063,3.313 0.615,0.198 10 false A53*3 5.448,3.292 6.063,3.49 0.615,0.198 10 false ECM 5.135,4.833 6.25,5.083 1.115,0.25 10 false Pickup Sensor 1.333,3.271 1.948,3.469 0.615,0.198 10 false ECM 1,4.792 1.615,4.99 0.615,0.198 10 false B34*4 1.01,4.958 2.208,5.188 1.198,0.229 10 false Igniter Assembly 0.156,5.635 1.323,5.875 1.167,0.24 10 false *1: for N04C-UH 0.167,6.01 2.073,6.219 1.906,0.208 10 false *2: for N04C-VL, N04C-VQ 0.167,6.417 1.448,6.625 1.281,0.208 10 false *3: for 2TR-FE 0.177,6.823 1.677,7.01 1.5,0.188 10 false *4: for 1BZ-FPE 0.188,7.219 1.208,7.438 1.021,0.219 10 false *5: for 1HZ 1.302,1.635 1.917,1.833 0.615,0.198 10 false ECM


CAUTION / NOTICE / HINT

NOTICE:
·

The meter/gauge system uses the CAN communication system. First, confirm that there is no malfunction in the CAN communication system. Refer to the How to Proceed with Troubleshooting procedure (Click hereVehicle Interior>METER / GAUGE / DISPLAY>METER / GAUGE SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING).

·

When replacing the combination meter assembly, always replace it with a new one. If a combination meter assembly which was installed to another vehicle used, the information stored in it will not match the information from the vehicle and a DTC may be stored.



PROCEDURE

1.CHECK VEHICLE CONDITION
Result:
Result proceed to
w/ Multi-information Display A
w/o Multi-information Display B



A

2.CHECK FOR DTC (ECD SYSTEM, SFI SYSTEM)

B

6.CONFIRM ENGINE MODEL
2.CHECK FOR DTC (ECD SYSTEM, SFI SYSTEM)
a.

Check for DTCs.


OK:

ECD system (for N04C) or SFI system (for 2TR-FE) DTC is not output.



Result:
Result proceed to
OK A
NG (for N04C) B
NG (for 2TR-FE) C



A

3.PERFORM ACTIVE TEST USING GTS (TACHOMETER OPERATION)

B

C

3.PERFORM ACTIVE TEST USING GTS (TACHOMETER OPERATION)
a.

Using the GTS, perform the Active Test (Click hereVehicle Interior>METER / GAUGE / DISPLAY>METER / GAUGE SYSTEM>DATA LIST / ACTIVE TEST).

Combination Meter:
Tester Display Test Part Control Range Diagnostic Note
TachoMeter Operation Tachometer OFF, 0, 1000, 2000, 3000, 4000, 5000 or 6000 (rpm) Make sure that the vehicle is stopped and the engine is idling.

OK:

Needle indication is normal according to the GTS operation.



Result:
Result proceed to
OK A
NG (for N04C) B
NG (for 2TR-FE) C



A

4.READ VALUE USING GTS (ENGINE RPM)

B

C

4.READ VALUE USING GTS (ENGINE RPM)
a.

Using the GTS, read the Data List (Click hereVehicle Interior>METER / GAUGE / DISPLAY>METER / GAUGE SYSTEM>DATA LIST / ACTIVE TEST).

Combination Meter:
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
Engine Rpm Engine speed / Min.: 0 rpm, Max.: 12750 rpm Actual engine speed -

OK:

Engine speed displayed on the GTS is almost the same as actual engine speed.



Result:
Result proceed to
OK A
NG (for N04C) B
NG (for 2TR-FE) C



A

5.READ VALUE USING GTS (ENGINE SPEED, ENGINE RPM)

B

C

5.READ VALUE USING GTS (ENGINE SPEED, ENGINE RPM)
a.

Using the GTS, read the Data List (Click hereVehicle Interior>METER / GAUGE / DISPLAY>METER / GAUGE SYSTEM>DATA LIST / ACTIVE TEST).

Engine:
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
Engine Speed Engine speed / Min.: 0 rpm, Max.: 16383 rpm Actual engine speed -

Combination Meter:
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
Engine Rpm Engine speed / Min.: 0 rpm, Max.: 12750 rpm Actual engine speed -

OK:

"Engine Speed" displayed on GTS is same as "Engine Rpm" displayed on GTS.



Result:
Result proceed to
OK A
NG (for N04C) B
NG (for 2TR-FE) C



A

REPLACE COMBINATION METER ASSEMBLY

B

C

6.CONFIRM ENGINE MODEL
Result:
Result proceed to
except 1HZ A
for 1HZ, 1BZ-FPE B



A

7.READ VALUE USING GTS (ENGINE SPEED)

B

8.CHECK COMBINATION METER ASSEMBLY
7.READ VALUE USING GTS (ENGINE SPEED)
a.

Using the GTS, read the Data List (Click hereVehicle Interior>METER / GAUGE / DISPLAY>METER / GAUGE SYSTEM>DATA LIST / ACTIVE TEST).

Engine:
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
Engine Rpm Engine speed / Min.: 0 rpm, Max.: 12750 rpm Actual engine speed -

OK:

Engine speed displayed on the GTS is almost the same as actual engine speed.


HINT:
·

for N04C-UH: If it is necessary to refer to the ECD system, refer to the following procedures (Click hereEngine / Hybrid System>N04C-UH (ENGINE CONTROL)>ECD SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING).

·

for N04C-VL: If it is necessary to refer to the ECD system, refer to the following procedures (Click hereEngine / Hybrid System>N04C-VL (ENGINE CONTROL)>ECD SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING).

·

for N04C-VQ: If it is necessary to refer to the ECD system, refer to the following procedures (Click hereEngine / Hybrid System>N04C-VQ (ENGINE CONTROL)>ECD SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING).

·

for 1BZ-FPE: If it is necessary to refer to the electronic controlled carburetor system, refer to the following procedures (Click hereEngine / Hybrid System>1BZ-FPE (ENGINE CONTROL)>ELECTRONIC CONTROLLED CARBURETOR SYSTEM>PROBLEM SYMPTOMS TABLE).

·

for 2TR-FE: If it is necessary to refer to the SFI system, refer to the following procedures (Click hereEngine / Hybrid System>2TR-FE (ENGINE CONTROL)>SFI SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING).




Result:
Result proceed to
OK A
NG (except 2TR-FE and 1BZ-FPE) B
NG (for 1BZ-FPE) C
NG (for 2TR-FE) D



A

CHECK COMBINATION METER ASSEMBLY

B

GO TO ECD SYSTEM

C

GO TO ELECTRONIC CONTROLLED CARBURETOR SYSTEM

D

GO TO SFI SYSTEM

8.CHECK COMBINATION METER ASSEMBLY
a.

Check the input waveform.

E402252E01
0.354,1.292 0.76,1.552 0.406,0.26 1.99,1.427 2.417,0.979 2.417,0.979 2.604,0.979 true 0.146,0.125 0.458,0.323 0.313,0.198 10 false *1 0.49,1.344 0.802,1.542 0.313,0.198 10 false J1 6.385,1.563 6.865,1.76 0.479,0.198 10 false GND 2.708,0.906 3.021,1.104 0.313,0.198 10 false S

Text in Illustration
*1 Component with harness connected
(Combination Meter Assembly)
- -

i.

Remove the combination meter assembly with the connector still connected.


ii.

Connect an oscilloscope to terminal J1-5 (S) and body ground.


iii.

Start the engine.


iv.

Check the signal waveform according to the condition(s) in the table below.

Item Condition
Tool Setting 5 V/DIV., 10 ms/DIV.
Vehicle Condition Engine idling

OK:

The waveform is displayed as shown in the illustration.


HINT:

As the vehicle speed increases, the cycle of the signal waveform narrows.



v.

Reinstall the combination meter assembly.



Result:
Result proceed to
OK A
NG (for 1HZ) B
NG (for 1BZ-FPE) C



A

REPLACE COMBINATION METER ASSEMBLY

B

9.CHECK HARNESS AND CONNECTOR (PICKUP SENSOR - COMBINATION METER ASSEMBLY AND BODY GROUND)

C

11.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - IGNITER ASSEMBLY)
9.CHECK HARNESS AND CONNECTOR (PICKUP SENSOR - COMBINATION METER ASSEMBLY AND BODY GROUND)
a.

Disconnect the J1 combination meter assembly connector.


b.

Disconnect the B23 pickup sensor connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
J1-5 (S) - B23-1 (NE+) Always Below 1 Ω
B23-2 (NE-) - Body ground Always Below 1 Ω
B23-2 (NE-) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

10.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

10.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - BODY GROUND)
a.
E199460E06
0.281,1.125 0.708,1.417 0.427,0.292 1.688,0.51 1.49,0.51 1.49,0.51 1.385,1.26 true 0.188,0.146 0.354,0.323 0.167,0.177 10 false *1 0.417,1.188 0.708,1.406 0.292,0.219 10 false J1 1.76,0.448 1.917,0.646 0.156,0.198 10 false S

Disconnect the J1 combination meter assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
J1-5 (S) - Body ground Always Approximately 730 Ω


Text in Illustration
*1 Front view of wire harness connector
(to Combination Meter Assembly)


Result:
Proceed to
OK
NG



OK

REPLACE COMBINATION METER ASSEMBLY

NG

REPLACE PICKUP SENSOR

11.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - IGNITER ASSEMBLY)
a.

Disconnect the J1 combination meter assembly connector.


b.

Disconnect the B34 igniter assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
J1-5 (S) - B34-4 (IG4) Always Below 1 Ω
J1-5 (S) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE IGNITER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR