Home › Drivetrain › A861E (AUTOMATIC TRANSMISSION / TRANSAXLE) › AUTOMATIC TRANSMISSION SYSTEM › from 2019.08
RM2850E _52 Drivetrain _082622 A861E AUTOMATIC TRANSMISSION / TRANSAXLE _0398655 AUTOMATIC TRANSMISSION SYSTEM C

A861E AUTOMATIC TRANSMISSION / TRANSAXLE  AUTOMATIC TRANSMISSION SYSTEM  P2716  Pressure Control Solenoid "D" Electrical  


DESCRIPTION

Based on signals from the throttle position sensor, the transmission control ECU assembly controls the line pressure control solenoid according to a predetermined current. In this way, line pressure is adjusted to match throttle opening angle and engine output.

DTC No. Detection Item DTC Detection Condition Trouble Area Warning Indicate Memory
P2716 Pressure Control Solenoid "D" Electrical 1. Diagnosis Condition 2. Malfunction Status 3. Malfunction Time 4. Other
DTC Detection Condition 1:
1.

-

2.

Shift solenoid valve SL4 resistance 100 kΩ or more

3.

0.065 seconds or more

4.

1 trip detection logic


DTC Detection Condition 2:
1.

-

2.

Shift solenoid valve SL4 current 4 A or more

3.

0.1 seconds or more

4.

1 trip detection logic


·

Wire harness or connector (Shift solenoid valve SL4 signal circuit)

·

No. 2 transmission wire

·

Transmission valve body assembly (Shift solenoid valve SL4)

·

Transmission control ECU assembly


O/D OFF Indicator Light: Blinking DTC stored

CONFIRMATION DRIVING PATTERN

HINT:

After the repair, clear the DTCs and perform the following procedure to check that DTCs are not output.



WIRING DIAGRAM

C372565E05
1.49,1.729 3.365,1.906 1.875,0.177 10 false Shift Solenoid Valve SL4 1.042,2.708 1.396,2.885 0.354,0.177 10 false B138 1.042,2.875 3.167,3.281 2.125,0.406 10 false Transmission valve body assembly (No. 2 Transmission Wire) 4.708,3.031 5.115,3.229 0.406,0.198 10 false B132 5.094,3.031 6.417,3.438 1.323,0.406 10 false Transmission Control ECU Assembly 3.469,1.125 3.833,1.292 0.365,0.167 10 false SL4+ 3.469,2.104 3.833,2.271 0.365,0.167 10 false SL4- 5.177,1.146 5.542,1.313 0.365,0.167 10 false SL4+ 5.188,2.104 5.552,2.271 0.365,0.167 10 false SL4- 5.76,1.25 5.958,1.438 0.198,0.188 10 false IC 3.906,1.125 4.125,1.302 0.219,0.177 10 false 11 3.958,2.104 4.177,2.281 0.219,0.177 10 false 5 4.896,1.146 5.115,1.323 0.219,0.177 10 false 30 4.896,2.104 5.115,2.281 0.219,0.177 10 false 31 1.063,1.313 1.219,1.51 0.156,0.198 10 false 1 1.063,2.156 1.219,2.354 0.156,0.198 10 false 2

CAUTION / NOTICE / HINT

NOTICE:
·

When inspecting each shift solenoid valve, do not remove it from the transmission valve body assembly.

·

Perform initialization when parts related to the automatic transmission are replaced.

Click hereDrivetrain>A861E (AUTOMATIC TRANSMISSION / TRANSAXLE)>AUTOMATIC TRANSMISSION SYSTEM>INITIALIZATION



HINT:
·

Refer to Parts Location for the location of each shift solenoid valve and each oil pressure switch.

Click hereDrivetrain>A861E (AUTOMATIC TRANSMISSION / TRANSAXLE)>AUTOMATIC TRANSMISSION SYSTEM>PARTS LOCATION

·

Use a new transmission wire if the pin and socket terminals are removed on each oil pressure switch.



PROCEDURE

1.INSPECT NO. 2 TRANSMISSION WIRE (SHIFT SOLENOID VALVE SL4)
a.

Disconnect the No. 2 transmission wire connector.


b.
C239950C09
0.896,1.75 1.281,1.094 true 1.74,1.74 1.406,1.26 true 0.198,0.135 0.469,0.323 0.271,0.188 10 false *a 0.813,1.792 1.219,1.979 0.406,0.188 10 false SL4- 1.667,1.771 2.073,1.958 0.406,0.188 10 false SL4+
*a Component without harness connected
(No. 2 Transmission Wire)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
11 (SL4+) - 5 (SL4-) 20°C (68°F) 5.0 to 6.0 Ω
11 (SL4+) or 5 (SL4-) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

2.CHECK HARNESS AND CONNECTOR (NO. 2 TRANSMISSION WIRE - TRANSMISSION CONTROL ECU ASSEMBLY)

NG

3.INSPECT SHIFT SOLENOID VALVE SL4
2.CHECK HARNESS AND CONNECTOR (NO. 2 TRANSMISSION WIRE - TRANSMISSION CONTROL ECU ASSEMBLY)
a.

Disconnect the transmission control ECU assembly connector.


b.
C233560C14
1,0.073 1.385,0.313 0.385,0.24 1.646,1.948 0.938,1.76 true 0.885,1.75 0.719,1.927 true 0.073,0.063 0.25,0.229 0.177,0.167 10 false *a 1.031,0.115 1.49,0.292 0.458,0.177 10 false B132 1.74,1.885 2.479,2.083 0.74,0.198 10 false 30 (SL4+) 0.104,1.885 0.823,2.073 0.719,0.188 10 false 31 (SL4-)
*a Rear view of wire harness connector
(to Transmission Control ECU Assembly)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
B132-30 (SL4+) - B132-31 (SL4-) 20°C (68°F) 5.0 to 6.0 Ω
B132-30 (SL4+) or B132-31 (SL4-) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE TRANSMISSION CONTROL ECU ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.INSPECT SHIFT SOLENOID VALVE SL4
a.
C366074C02
1.865,0.646 2.281,0.229 true 1.458,0.646 1.031,0.208 true 0.104,0.104 0.417,0.302 0.313,0.198 10 false *a 2.333,0.156 2.49,0.354 0.156,0.198 10 false 1 0.906,0.156 1.063,0.354 0.156,0.198 10 false 2
*a Component without harness connected
(Shift Solenoid Valve SL4)


Disconnect the shift solenoid valve SL4 connector.

Click hereDrivetrain>A861E (AUTOMATIC TRANSMISSION / TRANSAXLE)>AUTOMATIC TRANSMISSION SYSTEM>PARTS LOCATION

NOTICE:

When inspecting the shift solenoid valve SL4, do not remove it from the transmission valve body assembly.



b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
1 - 2 20°C (68°F) 5.0 to 6.0 Ω



Result:
Proceed to
OK
NG



OK

NG