Home › Engine / Hybrid System › N04C-WA (ENGINE CONTROL) › ECD SYSTEM › from 2019.08
RM2850E _51 Engine / Hybrid System _082611 N04C-WA ENGINE CONTROL _0399963 ECD SYSTEM C

N04C-WA ENGINE CONTROL  ECD SYSTEM  P22A7  NOx Sensor Heater Sense Circuit Range/Performance Bank 1 Sensor 2  


DESCRIPTION

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P22A7 NOx Sensor Heater Sense Circuit Range/Performance Bank 1 Sensor 2 Diagnosis Condition:
·

Ignition switch ON

·

Power supply voltage for nitrogen oxides sensor is in the range of 10 to 16 V.

·

Exhaust gas temperature at SCR outlet from No. 5 exhaust gas temperature sensor is higher than 180°C (356°F).


Malfunction Status:

NOx sensor controller detects system failure that failure in heater is continued for at least 10 seconds.


Malfunction Duration:

30 seconds or more


·

No. 2 nitrogen oxides sensor

·

Harness or connector


Class A DTC stored

MONITOR DESCRIPTION

·

The NOx sensor No. 2 are controlled by the NOx sensor controller.

·

The NOx sensor controller is connected via the ECM and DCU through CAN communication, and it sends and receives data.


CONFIRMATION DRIVING PATTERN

DTC No. DTC Detection Drive Pattern
P22A7 PM forced regeneration

WIRING DIAGRAM

CAUTION / NOTICE / HINT

NOTICE:

After replacing the ECM, the new ECM needs registration (Click hereEngine / Hybrid System>N04C-WA (ENGINE CONTROL)>ECD SYSTEM>REGISTRATION) and initialization (Click hereEngine / Hybrid System>N04C-WA (ENGINE CONTROL)>ECD SYSTEM>INITIALIZATION).


HINT:

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.


PROCEDURE

1.CHECK CONNECTOR CONNECTION CONDITION
a.

Check the connector connection for the No. 2 nitrogen oxides sensor connector.

Standard:

The connector is connected securely and there are no contact pressure problems.



Result:
Proceed to
OK
NG



OK

2.CHECK HARNESS AND CONNECTOR

NG

23.CONNECT SECURELY
2.CHECK HARNESS AND CONNECTOR
A383897C40
1.521,0.208 1.99,0.542 0.469,0.333 2.063,1.76 1.75,1.281 true 1.229,1.75 1.448,1.281 true 0.188,0.135 0.5,0.333 0.313,0.198 10 false *a 1.615,0.292 1.927,0.49 0.313,0.198 10 false P14 0.875,1.771 1.333,1.969 0.458,0.198 10 false CANH 2.083,1.76 2.625,1.958 0.542,0.198 10 false CANL
*a Front view of wire harness connector
(to No. 2 Nitrogen Oxides Sensor)


a.

Disconnect the No. 2 nitrogen oxides sensor connector.


b.

Measure the waveform of the ECM connector using an oscilloscope.

Standard Voltage:
Tester Connection Condition Specified Condition
P14-2 (CANH) - P14-3 (CANL) Ignition switch ON Pulse waves
0 to 5 V



Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (NO. 2 NITROGEN OXIDES SENSOR - BODY GROUND)

NG

22.REPAIR OR REPLACE HARNESS OR CONNECTOR
3.CHECK HARNESS AND CONNECTOR (NO. 2 NITROGEN OXIDES SENSOR - BODY GROUND)
A383897C41
1.521,0.208 1.99,0.542 0.469,0.333 2.292,1.74 1.979,1.26 true 0.188,0.135 0.5,0.333 0.313,0.198 10 false *a 1.615,0.292 1.927,0.49 0.313,0.198 10 false P14 2.271,1.771 2.813,1.969 0.542,0.198 10 false GND
*a Front view of wire harness connector
(to No. 2 Nitrogen Oxides Sensor)


a.

Disconnect the No. 2 nitrogen oxides sensor connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
P14-4 (GND) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

4.CHECK NO. 2 NITROGEN OXIDES SENSOR

NG

21.REPAIR OR REPLACE HARNESS OR CONNECTOR
4.CHECK NO. 2 NITROGEN OXIDES SENSOR
A383897C42
1.521,0.208 1.99,0.542 0.469,0.333 2.521,1.76 2.208,1.281 true 1.656,1.729 1.875,1.26 true 0.188,0.135 0.5,0.333 0.313,0.198 10 false *a 1.615,0.292 1.927,0.49 0.313,0.198 10 false P14 1.354,1.74 1.813,1.938 0.458,0.198 10 false GND 2.542,1.771 3.083,1.969 0.542,0.198 10 false VCC
*a Front view of wire harness connector
(to No. 2 nitrogen oxides sensor)


a.

Disconnect the No. 2 nitrogen oxides sensor connector.


b.

Turn the ignition switch to ON.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
P14-5 (VCC) - P14-4 (GND) Ignition switch ON 11 to 14 V



Result:
Proceed to
OK
NG



OK

5.CHECK CONNECTOR CONNECTION CONDITION (NO. 5 EXHAUST GAS TEMPERATURE SENSOR)

NG

20.REPAIR OR REPLACE HARNESS OR CONNECTOR
5.CHECK CONNECTOR CONNECTION CONDITION (NO. 5 EXHAUST GAS TEMPERATURE SENSOR)
a.

Check the connector connection for the No. 5 exhaust gas temperature sensor connector.

Standard:

The connector is connected securely and there are no contact pressure problems.



Result:
Proceed to
OK
NG



OK

6.CHECK NO. 5 EXHAUST GAS TEMPERATURE SENSOR

NG

19.CONNECT SECURELY
6.CHECK NO. 5 EXHAUST GAS TEMPERATURE SENSOR
a.

Check the installation of the No. 5 exhaust gas temperature sensor.


b.

Make sure there is no dirt, damage or clogging in the sensing unit of No. 5 exhaust gas temperature sensor.


Result:
Proceed to
OK
NG



OK

7.INSPECT NO. 5 EXHAUST GAS TEMPERATURE SENSOR

NG

18.REPAIR OR REPLACE NO. 5 EXHAUST GAS TEMPERATURE SENSOR
7.INSPECT NO. 5 EXHAUST GAS TEMPERATURE SENSOR
a.

Inspect the No. 5 exhaust gas temperature sensor.

Click hereEngine / Hybrid System>N04C-WA (EMISSION CONTROL)>EXHAUST GAS TEMPERATURE SENSOR>INSPECTION


Result:
Proceed to
OK
NG



OK

8.CHECK CONNECTOR CONNECTION CONDITION (ENGINE COOLANT TEMPERATURE SENSOR CONNECTOR)

NG

17.REPLACE NO. 5 EXHAUST GAS TEMPERATURE SENSOR
8.CHECK CONNECTOR CONNECTION CONDITION (ENGINE COOLANT TEMPERATURE SENSOR CONNECTOR)
a.

Check the connector connection for the engine coolant temperature sensor connector.

Standard:

The connector is connected securely and there are no contact pressure problems.



Result:
Proceed to
OK
NG



OK

9.CHECK ENGINE COOLANT TEMPERATURE SENSOR

NG

16.CONNECT SECURELY
9.CHECK ENGINE COOLANT TEMPERATURE SENSOR
a.

Check the installation of the engine coolant temperature sensor.


b.

Make sure there is no dirt, damage or clogging in the sensing unit of the engine coolant temperature sensor.


Result:
Proceed to
OK
NG



OK

10.INSPECT ENGINE COOLANT TEMPERATURE SENSOR

NG

15.REPAIR OR REPLACE ENGINE COOLANT TEMPERATURE SENSOR
10.INSPECT ENGINE COOLANT TEMPERATURE SENSOR
a.

Result:
Proceed to
OK
NG



OK

11.REPLACE NO .2 NITROGEN OXIDES SENSOR

NG

14.REPLACE ENGINE COOLANT TEMPERATURE SENSOR
11.REPLACE NO .2 NITROGEN OXIDES SENSOR
a.

Result:
Proceed to
NEXT



NEXT

12.CHECK DTC OUTPUT
12.CHECK DTC OUTPUT
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Clear the DTCs.

HINT:

Clear the DTCs with the engine stopped, as DTCs cannot be cleared while the engine is running.



d.

Turn the ignition switch off for 30 seconds or more.


e.

Perform the confirmation driving pattern.


f.

Turn the GTS on.


g.

Enter the following menus: Powertrain / Engine / Trouble Codes.


h.

Read Current DTCs.

Result:
Result Proceed to
DTC P22A7 is output A
DTCs are not output B




A

13.REPLACE ECM

B

END

13.REPLACE ECM

Result:
Proceed to
NEXT



NEXT

24.CHECK DTC OUTPUT
14.REPLACE ENGINE COOLANT TEMPERATURE SENSOR
a.

Result:
Proceed to
NEXT



NEXT

24.CHECK DTC OUTPUT
15.REPAIR OR REPLACE ENGINE COOLANT TEMPERATURE SENSOR
a.

Repair or replace the engine coolant temperature sensor.


Result:
Proceed to
NEXT



NEXT

24.CHECK DTC OUTPUT
16.CONNECT SECURELY
a.

Connect securely the engine coolant temperature sensor.

HINT:

Repair it as needed.



Result:
Proceed to
NEXT



NEXT

24.CHECK DTC OUTPUT
17.REPLACE NO. 5 EXHAUST GAS TEMPERATURE SENSOR
a.

Replace the No. 5 exhaust gas temperature sensor.

Click hereEngine / Hybrid System>N04C-WA (EMISSION CONTROL)>EXHAUST GAS TEMPERATURE SENSOR>REMOVAL


Result:
Proceed to
NEXT



NEXT

24.CHECK DTC OUTPUT
18.REPAIR OR REPLACE NO. 5 EXHAUST GAS TEMPERATURE SENSOR
a.

Repair or replace the No. 5 exhaust gas temperature sensor.


Result:
Proceed to
NEXT



NEXT

24.CHECK DTC OUTPUT
19.CONNECT SECURELY
a.

Connect securely the No. 5 exhaust gas temperature sensor connector.

HINT:

Repair it as needed.



Result:
Proceed to
NEXT



NEXT

24.CHECK DTC OUTPUT
20.REPAIR OR REPLACE HARNESS OR CONNECTOR
a.

Repair or replace the harness or connector.


Result:
Proceed to
NEXT



NEXT

24.CHECK DTC OUTPUT
21.REPAIR OR REPLACE HARNESS OR CONNECTOR
a.

Repair or replace the harness or connector.


Result:
Proceed to
NEXT



NEXT

24.CHECK DTC OUTPUT
22.REPAIR OR REPLACE HARNESS OR CONNECTOR
a.

Repair or replace the harness or connector.


Result:
Proceed to
NEXT



NEXT

24.CHECK DTC OUTPUT
23.CONNECT SECURELY
a.

Connect securely the No. 2 nitrogen oxides sensor connector.

HINT:

Repair it as needed.



Result:
Proceed to
NEXT



NEXT

24.CHECK DTC OUTPUT
24.CHECK DTC OUTPUT
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Clear the DTCs.

HINT:

Clear the DTCs with the engine stopped, as DTCs cannot be cleared while the engine is running.



d.

Turn the ignition switch off for 30 seconds or more.


e.

Perform the confirmation driving pattern.


f.

Turn the GTS on.


g.

Enter the following menus: Powertrain / Engine / Trouble Codes.


h.

Confirm that the DTC is not output again.


Result:
Proceed to
NEXT



NEXT

END