Home › Engine / Hybrid System › N04C-WA (ENGINE CONTROL) › ECD SYSTEM › from 2019.08
RM2850E _51 Engine / Hybrid System _082611 N04C-WA ENGINE CONTROL _0399963 ECD SYSTEM C

N04C-WA ENGINE CONTROL  ECD SYSTEM  P20CF  Exhaust Aftertreatment Fuel Injector "A" Stuck Open  


DESCRIPTION

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P20CF Exhaust Aftertreatment Fuel Injector "A" Stuck Open Diagnosis Condition:
Judgement on fuel injector leakage with fuel temperature
·

The battery voltage is in the range of 10 to 16 V.

·

Not DPR regenerating, or not at instant following the DPR regenerating

·

No. 3 exhaust gas temperature is higher than 200°C (392°F).

·

DTC P2032 or P2033 is not detected.

·

Engine is running under normal operating conditions.


Judgement on fuel injector leakage with fuel pressure
·

The battery voltage is in the range of 10 to 16 V.

·

Engine runs at speeds over 400 rpm.

·

Engine coolant temperature is at least 0°C (32°F).

·

Intake air temperature is at least -20°C (-4°F).

The conditions described above continues for at least 10 seconds.


Judgement on fuel injector clogging
·

While manual DPR regenerating

·

Ignition switch ON

·

The battery voltage is in the range of 10 to 16 V.

The conditions described above continues for at least 5 seconds.


Malfunction Status:
Judgement on fuel injector leakage with fuel temperature

Temperature difference that No. 3 exhaust gas temperature is 390°C (734°F) or more higher than No. 2 exhaust gas temperature continues for at least 30 seconds.


Judgement on fuel injector leakage with fuel pressure

The condition that the pressure of the exhaust fuel addition injector is lower than the threshold value continues for at least 2 seconds.


Judgement on fuel injector clogging

The condition that the No. 3 exhaust gas temperature does not reach to the target temperature occurs twice in succession even though the integrated amount of the fuel injection quantity reaches to the specified quantities.


Malfunction Duration:
Judgement on fuel injector leakage with fuel temperature

30 seconds or more


Judgement on fuel injector leakage with fuel pressure

2 seconds or more


Judgement on fuel injector clogging

5 seconds or more


·

Exhaust fuel addition injector assembly

·

No. 2 exhaust gas temperature sensor

·

No. 3 exhaust gas temperature sensor

·

DOC catalyst

·

Fuel cutoff valve

·

Fuel filter

·

Fuel pipe

·

Fuel hose

·

Orifice bolt


- DTC stored

CONFIRMATION DRIVING PATTERN

DTC No. DTC Detection Drive Pattern
P20CF
·

Warm up the engine for 30 seconds or more.

·

PM forced regeneration



CAUTION / NOTICE / HINT

NOTICE:

After replacing the ECM, the new ECM needs registration (Click hereEngine / Hybrid System>N04C-WA (ENGINE CONTROL)>ECD SYSTEM>REGISTRATION) and initialization (Click hereEngine / Hybrid System>N04C-WA (ENGINE CONTROL)>ECD SYSTEM>INITIALIZATION).


HINT:

P20CF may be output if the fuel has frozen during winter or in cold regions.

Check that diesel fuel appropriate for the outside temperature is being used during winter or in cold regions.

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.


PROCEDURE

1.CHECK DTC OUTPUT
a.

Turn the ignition switch to ON and turn the ignition switch off and wait for 5 seconds or more.


b.

Connect the GTS to the DLC3.


c.

Turn the ignition switch to ON.


d.

Turn the GTS on.


e.

Enter the following menus: Powertrain / Engine / Trouble Codes.


f.

Read the DTCs.

Result:
Result Proceed to
DTC P20CF is output A
DTC P20CF and other DTC are output B




A

2.INSPECT NO. 3 EXHAUST GAS TEMPERATURE SENSOR

B

2.INSPECT NO. 3 EXHAUST GAS TEMPERATURE SENSOR
a.

Inspect the No. 3 exhaust gas temperature sensor.

Click hereEngine / Hybrid System>N04C-WA (EMISSION CONTROL)>EXHAUST GAS TEMPERATURE SENSOR>INSPECTION


Result:
Proceed to
OK
NG



OK

3.INSPECT NO. 2 EXHAUST GAS TEMPERATURE SENSOR

NG

17.REPLACE NO. 3 EXHAUST GAS TEMPERATURE SENSOR
3.INSPECT NO. 2 EXHAUST GAS TEMPERATURE SENSOR
a.

Inspect the No. 2 exhaust gas temperature sensor.

Click hereEngine / Hybrid System>N04C-WA (EMISSION CONTROL)>EXHAUST GAS TEMPERATURE SENSOR>INSPECTION


Result:
Proceed to
OK
NG



OK

4.INSPECT NO. 2 FUEL PRESSURE SENSOR

NG

16.REPLACE NO. 2 EXHAUST GAS TEMPERATURE SENSOR
4.INSPECT NO. 2 FUEL PRESSURE SENSOR
a.

Check the installation of the No. 2 fuel pressure sensor.


b.

Check the sensing unit of the No. 2 fuel pressure sensor for dirt, damage, or clogging.


Result:
Proceed to
OK
NG



OK

5.CLEAN EXHAUST FUEL ADDITION INJECTOR ASSEMBLY

NG

15.REPAIR OR REPLACE NO. 2 FUEL PRESSURE SENSOR
5.CLEAN EXHAUST FUEL ADDITION INJECTOR ASSEMBLY
a.

Clean the exhaust fuel addition injector assembly and its holder, and check if carbon was deposited

NOTICE:

Do not touch the nozzle spout with your hands or wipe it with a cloth.



Result:
Proceed to
NEXT



NEXT

6.INSPECT FUEL ADDITION CUT VALVE ASSEMBLY
6.INSPECT FUEL ADDITION CUT VALVE ASSEMBLY
a.

Inspect the fuel addition cut valve assembly.

Click hereEngine / Hybrid System>N04C-WA (FUEL)>FUEL ADDITION CUT VALVE ASSEMBLY>INSPECTION


Result:
Proceed to
OK
NG



OK

7.CHECK FUEL PIPE

NG

14.REPLACE FUEL ADDITION CUT VALVE ASSEMBLY
7.CHECK FUEL PIPE
a.

Check the fuel pipes for damage, fuel leaks, bleeding, etc.


Result:
Proceed to
OK
NG



OK

8.CHECK FUEL FILTER ELEMENT SUB-ASSEMBLY

NG

13.REPAIR OR REPLACE FUEL PIPE
8.CHECK FUEL FILTER ELEMENT SUB-ASSEMBLY
a.

Make sure there is no dirt, damage or clogging in the sensing unit of the fuel filter element sub-assembly.


Result:
Proceed to
OK
NG



OK

9.PERFORM PM FORCED REGENERATION

NG

12.REPAIR OR REPLACE FUEL FILTER ELEMENT SUB-ASSEMBLY
9.PERFORM PM FORCED REGENERATION
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Enter the following menus: Powertrain / Engine / Utility / DPR Check.

i.

Select "Check Start" and check according to the GTS display.


ii.

Select "DPR ALL Items Reset" and reset according to the GTS display.


iii.

Exit the inspection screen.



d.

Clear the DTCs.

HINT:

Clear the DTCs with the engine stopped, as DTCs cannot be cleared while the engine is running.



e.

Perform PM forced regeneration.

Click hereEngine / Hybrid System>N04C-WA (ENGINE CONTROL)>ECD SYSTEM>DPF FORCIBLE REGENERATION PROCEDURE

OK:

PM forced regeneration completes normally.



Result:
Proceed to
OK
NG



OK

10.CHECK DTC OUTPUT

NG

11.CHECK DTC OUTPUT
10.CHECK DTC OUTPUT
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Enter the following menus: Powertrain / Engine / Trouble Codes.


d.

Confirm that the DTC is not output again.


Result:
Proceed to
NEXT



NEXT

END

11.CHECK DTC OUTPUT
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Enter the following menus: Powertrain / Engine / Trouble Codes.


d.

Perform repairs according to the procedure for the output DTCs.


Result:
Proceed to
NEXT



NEXT

GO TO DTC CHART

12.REPAIR OR REPLACE FUEL FILTER ELEMENT SUB-ASSEMBLY
a.

Repair or replace the fuel filter element sub-assembly.


Result:
Proceed to
NEXT



NEXT

9.PERFORM PM FORCED REGENERATION
13.REPAIR OR REPLACE FUEL PIPE
a.

Repair or replace the fuel pipe.


Result:
Proceed to
NEXT



NEXT

9.PERFORM PM FORCED REGENERATION
14.REPLACE FUEL ADDITION CUT VALVE ASSEMBLY
a.

Replace the fuel addition cut valve assembly.

Click hereEngine / Hybrid System>N04C-WA (FUEL)>FUEL ADDITION CUT VALVE ASSEMBLY>REMOVAL


Result:
Proceed to
NEXT



NEXT

9.PERFORM PM FORCED REGENERATION
15.REPAIR OR REPLACE NO. 2 FUEL PRESSURE SENSOR
a.

Clean the sensing unit and install it properly.

HINT:

If damaged, replace the No. 2 fuel pressure sensor.



Result:
Proceed to
NEXT



NEXT

9.PERFORM PM FORCED REGENERATION
16.REPLACE NO. 2 EXHAUST GAS TEMPERATURE SENSOR
a.

Replace the No. 2 exhaust gas temperature sensor.

Click hereEngine / Hybrid System>N04C-WA (EMISSION CONTROL)>EXHAUST GAS TEMPERATURE SENSOR>REMOVAL


Result:
Proceed to
NEXT



NEXT

9.PERFORM PM FORCED REGENERATION
17.REPLACE NO. 3 EXHAUST GAS TEMPERATURE SENSOR
a.

Replace the No. 3 exhaust gas temperature sensor.

Click hereEngine / Hybrid System>N04C-WA (EMISSION CONTROL)>EXHAUST GAS TEMPERATURE SENSOR>REMOVAL


Result:
Proceed to
NEXT



NEXT

9.PERFORM PM FORCED REGENERATION