Home › Engine / Hybrid System › N04C-WA (ENGINE CONTROL) › ECD SYSTEM › from 2019.08
RM2850E _51 Engine / Hybrid System _082611 N04C-WA ENGINE CONTROL _0399963 ECD SYSTEM C

N04C-WA ENGINE CONTROL  ECD SYSTEM  P0005  Fuel Shutoff Valve "A" Control Circuit/Open  


DESCRIPTION

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P0005 Fuel Shutoff Valve "A" Control Circuit/Open Diagnosis Condition:
·

The engine revolution is 850 rpm or more.

·

The difference between the actual common rail pressure and the target common rail pressure is 7.8 MPa or less.


Malfunction Status:

The fuel pressure in the fuel addition fuel pipe is 0 MPa or less when the engine revolution is 750 rpm, and remains at 0.2 MPa or less for 30 seconds even when the engine revolution becomes 1000 rpm or more.


Malfunction Duration:

30 seconds or more


·

Fuel addition cut valve assembly

·

Fuel leakage (loose joint bolt), clogging, crush, and wrong assembly in fuel pipe


Class B1 DTC stored

MONITOR DESCRIPTION

The ECM monitors the fuel pressure in the fuel addition fuel pipe based on the value of the No. 2 fuel pressure sensor.

CONFIRMATION DRIVING PATTERN

DTC No. DTC Detection Drive Pattern
P0005 Engine speed 1000 rpm or more for 30 seconds or more

WIRING DIAGRAM

CAUTION / NOTICE / HINT

NOTICE:

After replacing the ECM, the new ECM needs registration (Click hereEngine / Hybrid System>N04C-WA (ENGINE CONTROL)>ECD SYSTEM>REGISTRATION) and initialization (Click hereEngine / Hybrid System>N04C-WA (ENGINE CONTROL)>ECD SYSTEM>INITIALIZATION).


HINT:

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.


PROCEDURE

1.CHECK DTC OUTPUT
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine / Trouble Codes.


e.

Read the DTCs.

Result:
Result Proceed to
DTC P0005 is output A
DTC P0005 and other DTCs are output B




A

2.CHECK HARNESS AND CONNECTOR

B

2.CHECK HARNESS AND CONNECTOR
a.
A409073C08
0.396,1.063 0.823,1.354 0.427,0.292 1.01,1.76 1.427,1.313 true 0.104,0.104 0.417,0.302 0.313,0.198 10 false *a 0.458,1.135 1.021,1.51 0.563,0.375 10 false B144 0.813,1.74 1.125,1.938 0.313,0.198 10 false +B
*a Front view of wire harness connector
(to Fuel Addition Cut Valve Assembly)


Disconnect the fuel addition cut valve assembly connector.


b.

Turn the ignition switch to ON.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
B144-1 (+B) - Body ground Ignition switch ON 4 V or more



Result:
Proceed to
OK
NG



OK

3.INSPECT FUEL ADDITION CUT VALVE ASSEMBLY DOWNSTREAM PIPE

NG

15.CHECK HARNESS AND CONNECTOR (CHECK FOR OPEN IN WIRE HARNESS)
3.INSPECT FUEL ADDITION CUT VALVE ASSEMBLY DOWNSTREAM PIPE
a.

Check if any of the following defects is found in the pipe between the fuel addition cut valve assembly and the exhaust fuel addition injector assembly.


·

Fuel leakage (loose joint bolt)

·

Crush

·

Wrong assembly


Result:
Proceed to
OK
NG



OK

4.INSPECT FUEL ADDITION CUT VALVE ASSEMBLY DOWNSTREAM PIPE (CLOGGING)

NG

14.REPAIR OR REPLACE DEFECTIVE PART
4.INSPECT FUEL ADDITION CUT VALVE ASSEMBLY DOWNSTREAM PIPE (CLOGGING)
a.

Bleed air from the fuel addition cut valve assembly downstream pipe and also check that there is no clogging in the pipe.


Result:
Proceed to
OK
NG



OK

5.INSPECT FUEL ADDITION CUT VALVE ASSEMBLY UPSTREAM PIPE

NG

9.REPLACE FUEL ADDITION CUT VALVE ASSEMBLY
5.INSPECT FUEL ADDITION CUT VALVE ASSEMBLY UPSTREAM PIPE
a.

Check if any of the following defects is found in the pipe between the supply pump assembly and the fuel addition cut valve assembly.

·

Fuel leakage (loose joint bolt)

·

Crush

·

Wrong assembly



Result:
Proceed to
OK
NG



OK

6.INSPECT FUEL ADDITION CUT VALVE ASSEMBLY UPSTREAM PIPE (CLOGGING)

NG

14.REPAIR OR REPLACE DEFECTIVE PART
6.INSPECT FUEL ADDITION CUT VALVE ASSEMBLY UPSTREAM PIPE (CLOGGING)
a.

Bleed air from the fuel addition cut valve assembly upstream pipe and also check that there is no clogging in the pipe.


Result:
Proceed to
OK
NG



OK

7.REPLACE FUEL ADDITION CUT VALVE ASSEMBLY

NG

8.CLEAN OR REPLACE FUEL ADDITION CUT VALVE ASSEMBLY UPSTREAM PIPE
7.REPLACE FUEL ADDITION CUT VALVE ASSEMBLY
a.

Replace the fuel addition cut valve assembly.

Click hereEngine / Hybrid System>N04C-WA (FUEL)>FUEL ADDITION CUT VALVE ASSEMBLY>REMOVAL


Result:
Proceed to
NEXT



NEXT

10.BLEED AIR FUEL SYSTEM
8.CLEAN OR REPLACE FUEL ADDITION CUT VALVE ASSEMBLY UPSTREAM PIPE
a.

Clean or replace the fuel addition cut valve assembly upstream pipe.


Result:
Proceed to
NEXT



NEXT

10.BLEED AIR FUEL SYSTEM
9.REPLACE FUEL ADDITION CUT VALVE ASSEMBLY
a.

Replace the fuel addition cut valve assembly.

Click hereEngine / Hybrid System>N04C-WA (FUEL)>FUEL ADDITION CUT VALVE ASSEMBLY>REMOVAL


Result:
Proceed to
NEXT



NEXT

10.BLEED AIR FUEL SYSTEM
10.BLEED AIR FUEL SYSTEM
a.

Bleed the air from the fuel system.

Click hereEngine / Hybrid System>N04C-WA (FUEL)>FUEL SYSTEM>ON-VEHICLE INSPECTION


Result:
Proceed to
NEXT



NEXT

11.CHECK DTC OUTPUT
11.CHECK DTC OUTPUT
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Clear the DTCs.

HINT:

Clear the DTCs with the engine stopped, as DTCs cannot be cleared while the engine is running.



d.

Turn the ignition switch off for 30 seconds or more.


e.

Perform the confirmation driving pattern.


f.

Turn the GTS on.


g.

Enter the following menus: Powertrain / Engine / Trouble Codes.


h.

Read Current DTCs.

Result:
Result Proceed to
DTC P0005 is output A
DTCs are not output B




A

12.REPLACE ECM

B

END

12.REPLACE ECM

Result:
Proceed to
NEXT



NEXT

13.CHECK DTC OUTPUT
13.CHECK DTC OUTPUT
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Clear the DTCs.

HINT:

Clear the DTCs with the engine stopped, as DTCs cannot be cleared while the engine is running.



d.

Turn the ignition switch off for 30 seconds or more.


e.

Perform the confirmation driving pattern.


f.

Turn the GTS on.


g.

Enter the following menus: Powertrain / Engine / Trouble Codes.


h.

Confirm that the DTC is not output again.


Result:
Proceed to
NEXT



NEXT

END

14.REPAIR OR REPLACE DEFECTIVE PART
a.

Repair or replace the defective part.


Result:
Proceed to
NEXT



NEXT

10.BLEED AIR FUEL SYSTEM
15.CHECK HARNESS AND CONNECTOR (CHECK FOR OPEN IN WIRE HARNESS)
a.
A405886C01
1.51,0.125 1.885,0.406 0.375,0.281 0.083,0.115 0.396,0.313 0.313,0.198 10 false *a 1.667,0.208 1.979,0.406 0.313,0.198 10 false E
*a Signal Check Harness Lead Connector


A409073C05
0.396,1.063 0.823,1.354 0.427,0.292 1.198,1.823 1.479,1.344 true 0.104,0.104 0.417,0.302 0.313,0.198 10 false *a 0.458,1.135 1.021,1.51 0.563,0.375 10 false B144 1.031,1.854 1.448,2.104 0.417,0.25 10 false +B
*a Front view of wire harness connector
(to Fuel Addition Cut Valve Assembly)


Disconnect the ECM connector.


b.

Disconnect the fuel addition cut valve assembly connector.


c.

Connect the signal check harness to the ECM vehicle side harness. (Do not connect harness to the ECM)


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
E-31 - B144-1 (+B) Always Below 1 Ω
E-31 or B144-1 (+B) - Body ground and other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

16.REPLACE ECM

NG

17.REPAIR OR REPLACE HARNESS OR CONNECTOR
16.REPLACE ECM

Result:
Proceed to
NEXT



NEXT

13.CHECK DTC OUTPUT
17.REPAIR OR REPLACE HARNESS OR CONNECTOR
a.

Repair or replace the harness or connector.


Result:
Proceed to
NEXT



NEXT

13.CHECK DTC OUTPUT