Home › Engine / Hybrid System › N04C-WA (ENGINE CONTROL) › ECD SYSTEM › from 2019.08
RM2850E _51 Engine / Hybrid System _082611 N04C-WA ENGINE CONTROL _0399963 ECD SYSTEM C

N04C-WA ENGINE CONTROL  ECD SYSTEM  P2002  Particulate Filter Efficiency Below Threshold Bank 1  


DESCRIPTION

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P2002 Particulate Filter Efficiency Below Threshold Bank 1 Diagnosis Condition:
·

Particulate matter sensor is active

·

After regeneration of PM sensor

·

DPR has not been regenerated

·

No. 5 exhaust gas temperature: 480°C (896°F) or less

·

Battery voltage is in the range of 10 V to 16 V

·

Amount of soot emission: 21% or more

After above condition is established, while the model calculated soot emission value changes 0% to 100%, the time that the below condition is established is half of time or more.

·

The engine revolution: 1500 rpm or more

·

The fuel injection quantity: 40 mm3/st or more

·

The atmospheric pressure: 75 kPa (10.9 psi) or more

·

The engine coolant temperature: 60°C (140°F) or more

·

The intake air temperature: -20°C (-4°F) or more

·

The No. 5 exhaust gas temperature: 125°C (257°F) or less

·

The exhaust gas flow speed: 90 m/s (27.4 ft/s) or more


Malfunction Status:

Failure is determined when the value of the calculated soot emission model quantity is 100% and the value of the measured soot emission quantity is 100%.


Malfunction Duration:

-


·

Monolithic converter assembly

·

Particulate matter sensor

·

No. 5 exhaust gas temperature sensor

·

Atmospheric pressure sensor (built into engine ECM)

·

Intake mass air flow meter sub-assembly

·

Crankshaft position sensor

·

Injector assembly

·

Diesel throttle body

·

EGR valve assembly

·

Engine coolant temperature sender

·

Turbocharger sub-assembly

·

ECM


Class B1 DTC stored

MONITOR DESCRIPTION

Based on the values of the soot emission quantity measured from the particulate matter sensor and the calculated model soot emission quantity, ECU detects clogging and erosion of the monolithic converter assembly.

CONFIRMATION DRIVING PATTERN

DTC No. DTC Detection Drive Pattern
P2002 PM forced regeneration


CAUTION / NOTICE / HINT

NOTICE:
·

After replacing the injector assembly, the ECM needs registration (Click here Engine / Hybrid System>N04C-WA (ENGINE CONTROL)>ECD SYSTEM>REGISTRATION).

·

After replacing the ECM, the new ECM needs registration (Click hereEngine / Hybrid System>N04C-WA (ENGINE CONTROL)>ECD SYSTEM>REGISTRATION) and initialization (Click hereEngine / Hybrid System>N04C-WA (ENGINE CONTROL)>ECD SYSTEM>INITIALIZATION).



HINT:

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.


PROCEDURE

1.CHECK DTC OUTPUT
a.

Turn the ignition switch to ON and turn the ignition switch off and wait for 5 seconds or more.


b.

Connect the GTS to the DLC3.


c.

Turn the ignition switch to ON.


d.

Turn the GTS on.


e.

Enter the following menus: Powertrain / Engine / Trouble Codes.


f.

Read the DTCs.

Result:
Result Proceed to
DTC P2002 is output A
DTCs other than P2002 are output B




A

2.INSPECT MONOLITHIC CONVERTER ASSEMBLY

B

2.INSPECT MONOLITHIC CONVERTER ASSEMBLY
a.

Remove the monolithic converter assembly and check if there is no soot, damages or other abnormalities at its end.


b.

Insert the check probe from the rear surface to inspect the inside.


c.

Check for proof of a forceful removal of the monolithic converter assembly.


Result:
Proceed to
OK
NG



OK

3.INSPECT PARTICULATE MATTER SENSOR CONNECTOR

NG

46.REPLACE MONOLITHIC CONVERTER ASSEMBLY
3.INSPECT PARTICULATE MATTER SENSOR CONNECTOR
a.

Check the connection of the particulate matter sensor connector. (Looseness and poor contact)


Result:
Proceed to
OK
NG



OK

4.INSPECT CRANKSHAFT POSITION SENSOR

NG

45.CONNECT SECURELY
4.INSPECT CRANKSHAFT POSITION SENSOR
a.

Check the connection of the crankshaft position sensor connector (Looseness and poor contact).


b.

Check the installation of the crankshaft position sensor.


Result:
Proceed to
OK
NG



OK

5.CHECK MANIFOLD ABSOLUTE PRESSURE SENSOR

NG

43.REPLACE CRANKSHAFT POSITION SENSOR
5.CHECK MANIFOLD ABSOLUTE PRESSURE SENSOR
a.

Check the installation of the manifold absolute pressure sensor.


b.

Make sure there is no dirt, damage or clogging in the sensing unit of the manifold absolute pressure sensor.


Result:
Proceed to
OK
NG



OK

6.CHECK READ VALUE USING GTS (ACTUAL BOOST PRESSURE)

NG

41.REPLACE MANIFOLD ABSOLUTE PRESSURE SENSOR
6.CHECK READ VALUE USING GTS (ACTUAL BOOST PRESSURE)
a.

Start the engine.


b.

Turn the GTS on.


c.

Enter the following menus: Powertrain / Engine and ECT / Data List / Actual Boost Pressure


d.

Race the engine from idle to NMR and verify that the boost pressure output signal varies.

Standard:

There is no abnormal change in the sensor output signal.

(The pressure sensor signal response changes according to the engine speed)



Result:
Proceed to
OK
NG



OK

7.CHECK ENGINE COOLANT TEMPERATURE SENSOR

NG

39.REPLACE MANIFOLD ABSOLUTE PRESSURE SENSOR
7.CHECK ENGINE COOLANT TEMPERATURE SENSOR
a.

Check the installation of the engine coolant temperature sensor.


b.

Make sure there is no dirt, damage or clogging in the sensing unit of the engine coolant temperature sensor.


Result:
Proceed to
OK
NG



OK

8.CHECK READ VALUE USING GTS (ENGINE COOLANT TEMPERATURE)

NG

37.REPAIR OR REPLACE ENGINE COOLANT TEMPERATURE SENSOR
8.CHECK READ VALUE USING GTS (ENGINE COOLANT TEMPERATURE)
a.

Ignition switch off.


b.

Connect the GTS to the DLC3.


c.

Start the engine.


d.

Turn the GTS on.


e.

Enter the following menus: Powertrain / Engine / Data List / Engine Coolant Temperature


f.

Read the value.


g.

Verify that the engine coolant temperature output value is 50°C (122°F) when the actual engine coolant temperature value is 50°C (122°F).

Standard values:

50°C (122°F)



Result:
Proceed to
OK
NG



OK

9.CHECK MASS AIR FLOW METER (INTAKE AIR TEMPERATURE SENSOR)

NG

35.REPLACE ENGINE COOLANT TEMPERATURE SENSOR
9.CHECK MASS AIR FLOW METER (INTAKE AIR TEMPERATURE SENSOR)
a.

Check the installation of the intake air temperature sensor (built into mass air flow meter).


b.

Make sure there is no dirt, damage or clogging in the sensing unit of the intake air temperature sensor (built into mass air flow meter).


Result:
Proceed to
OK
NG



OK

10.INSPECT MASS AIR FLOW METER (INTAKE AIR TEMPERATURE SENSOR)

NG

33.REPAIR OR REPLACE MASS AIR FLOW METER (INTAKE AIR TEMPERATURE SENSOR)
10.INSPECT MASS AIR FLOW METER (INTAKE AIR TEMPERATURE SENSOR)
a.

Inspect the intake air temperature sensor (built into mass air flow meter).

Click hereEngine / Hybrid System>N04C-WA (ENGINE CONTROL)>MASS AIR FLOW METER>INSPECTION


Result:
Proceed to
OK
NG



OK

11.CHECK CONNECTOR CONNECTION CONDITION

NG

32.REPLACE MASS AIR FLOW METER (INTAKE AIR TEMPERATURE SENSOR)
11.CHECK CONNECTOR CONNECTION CONDITION
a.

Check the connector connection for the No. 5 exhaust gas temperature sensor connector (looseness and poor contact).

Standard:

The connector is connected securely and there are no contact pressure problems.



Result:
Proceed to
OK
NG



OK

12.CHECK NO. 5 EXHAUST GAS TEMPERATURE SENSOR

NG

31.CONNECT SECURELY
12.CHECK NO. 5 EXHAUST GAS TEMPERATURE SENSOR
a.

Check the installation of the No. 5 exhaust gas temperature sensor.


b.

Make sure there is no dirt, damage or clogging in the sensing unit of the No. 5 exhaust gas temperature sensor.


Result:
Proceed to
OK
NG



OK

13.INSPECT NO. 5 EXHAUST GAS TEMPERATURE SENSOR

NG

30.REPAIR OR REPLACE NO. 5 EXHAUST GAS TEMPERATURE SENSOR
13.INSPECT NO. 5 EXHAUST GAS TEMPERATURE SENSOR
a.

Inspect the No. 5 exhaust gas temperature sensor.

Click hereEngine / Hybrid System>N04C-WA (EMISSION CONTROL)>EXHAUST GAS TEMPERATURE SENSOR>INSPECTION


Result:
Proceed to
OK
NG



OK

14.PERFORM ACTIVE TEST USING GTS (CONTROL THE EGR VALVE POSITION)

NG

29.REPLACE NO. 5 EXHAUST GAS TEMPERATURE SENSOR
14.PERFORM ACTIVE TEST USING GTS (CONTROL THE EGR VALVE POSITION)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Enter the following menus: Powertrain / Engine / Active Test / Control the EGR Valve Position / Data List / Actual EGR Valve Position and Target EGR Valve Position


d.

Check each step from 90 to 0% of the time lag of the target EGR valve opening and actual EGR valve opening.

NOTICE:

Perform the inspection while the engine is stopped to avoid engine damages.


Standard:

The response delay should be less than 5 seconds.



Result:
Proceed to
OK
NG



OK

15.PERFORM ACTIVE TEST USING GTS (CONTROL THE VN TURBO POSITION)

NG

27.REPLACE EGR VALVE ASSEMBLY
15.PERFORM ACTIVE TEST USING GTS (CONTROL THE VN TURBO POSITION)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the VN Turbo Position / Data List / Target VN Turbo Position / Actual VN Turbo Position


d.

Check each step from 90 to 0% of the time lag of the target VN turbo position and actual VN turbo position.

NOTICE:

Perform the inspection while the engine is stopped to avoid engine damages.


Standard:

The response delay should be less than 3 seconds.


Result:
Proceed to
OK
NG




OK

16.INSPECT DIESEL THROTTLE BODY (DIESEL THROTTLE VALVE)

NG

25.REPLACE TURBOCHARGER SUB-ASSEMBLY
16.INSPECT DIESEL THROTTLE BODY (DIESEL THROTTLE VALVE)
a.

Inspect the diesel throttle valve.

HINT:

Check if there are no abnormal opening angles or that the valve is not stuck.



Result:
Proceed to
OK
NG



OK

17.PERFORM ENGINE BASIC INSPECTION

NG

23.REPLACE DIESEL THROTTLE BODY
17.PERFORM ENGINE BASIC INSPECTION
a.

Perform the engine basic inspection with the diagnostic system.

(Check the injection quantity and the rotational fluctuation.)


Result:
Proceed to
OK
NG



OK

18.CHECK DTC OUTPUT

NG

21.REPLACE INJECTOR ASSEMBLY
18.CHECK DTC OUTPUT
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Clear the DTCs.

HINT:

Clear the DTCs with the engine stopped, as DTCs cannot be cleared while the engine is running.



d.

Start the engine and warm it up until the engine coolant temperature reaches 60°C (140°F) or higher.


e.

Turn the ignition switch off for 30 seconds or more.


f.

Perform the confirmation driving pattern.


g.

Turn the GTS on.


h.

Enter the following menus: Powertrain / Engine / Trouble Codes.


i.

Read Current DTCs.

Result:
Result Proceed to
DTC P2002 is output A
DTCs are not output B




A

19.REPLACE ECM

B

END

19.REPLACE ECM

Result:
Proceed to
NEXT



NEXT

20.CHECK DTC OUTPUT
20.CHECK DTC OUTPUT
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Clear the DTCs.

HINT:

Clear the DTCs with the engine stopped, as DTCs cannot be cleared while the engine is running.



d.

Start the engine and warm it up until the engine coolant temperature reaches 60°C (140°F) or higher.


e.

Turn the ignition switch off for 30 seconds or more.


f.

Perform the confirmation driving pattern.


g.

Turn the GTS on.


h.

Enter the following menus: Powertrain / Engine / Trouble Codes.


i.

Confirm that the DTC is not output again.


Result:
Proceed to
NEXT



NEXT

END

21.REPLACE INJECTOR ASSEMBLY
a.

Replace the injector assembly.

Click hereEngine / Hybrid System>N04C-WA (FUEL)>FUEL INJECTOR>REMOVAL


Result:
Proceed to
NEXT



NEXT

22.CHECK DTC OUTPUT
22.CHECK DTC OUTPUT
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Clear the DTCs.

HINT:

Clear the DTCs with the engine stopped, as DTCs cannot be cleared while the engine is running.



d.

Start the engine and warm it up until the engine coolant temperature reaches 60°C (140°F) or higher.


e.

Turn the ignition switch off for 30 seconds or more.


f.

Perform the confirmation driving pattern.


g.

Turn the GTS on.


h.

Enter the following menus: Powertrain / Engine / Trouble Codes.


i.

Confirm that the DTC is not output again.


Result:
Proceed to
NEXT



NEXT

18.CHECK DTC OUTPUT
23.REPLACE DIESEL THROTTLE BODY

Result:
Proceed to
NEXT



NEXT

24.CHECK DTC OUTPUT
24.CHECK DTC OUTPUT
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Clear the DTCs.

HINT:

Clear the DTCs with the engine stopped, as DTCs cannot be cleared while the engine is running.



d.

Start the engine and warm it up until the engine coolant temperature reaches 60°C (140°F) or higher.


e.

Turn the ignition switch off for 30 seconds or more.


f.

Perform the confirmation driving pattern.


g.

Turn the GTS on.


h.

Enter the following menus: Powertrain / Engine / Trouble Codes.


i.

Confirm that the DTC is not output again.


Result:
Proceed to
NEXT



NEXT

17.PERFORM ENGINE BASIC INSPECTION
25.REPLACE TURBOCHARGER SUB-ASSEMBLY
a.

Replace the turbocharger sub-assembly.

Click hereEngine / Hybrid System>N04C-WA (INTAKE)>TURBOCHARGER>REMOVAL


Result:
Proceed to
NEXT



NEXT

26.CHECK DTC OUTPUT
26.CHECK DTC OUTPUT
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Clear the DTCs.

HINT:

Clear the DTCs with the engine stopped, as DTCs cannot be cleared while the engine is running.



d.

Start the engine and warm it up until the engine coolant temperature reaches 60°C (140°F) or higher.


e.

Turn the ignition switch off for 30 seconds or more.


f.

Perform the confirmation driving pattern.


g.

Turn the GTS on.


h.

Enter the following menus: Powertrain / Engine / Trouble Codes.


i.

Confirm that the DTC is not output again.


Result:
Proceed to
NEXT



NEXT

16.INSPECT DIESEL THROTTLE BODY (DIESEL THROTTLE VALVE)
27.REPLACE EGR VALVE ASSEMBLY
a.

Result:
Proceed to
NEXT



NEXT

28.CHECK DTC OUTPUT
28.CHECK DTC OUTPUT
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Clear the DTCs.

HINT:

Clear the DTCs with the engine stopped, as DTCs cannot be cleared while the engine is running.



d.

Start the engine and warm it up until the engine coolant temperature reaches 60°C (140°F) or higher.


e.

Turn the ignition switch off for 30 seconds or more.


f.

Perform the confirmation driving pattern.


g.

Turn the GTS on.


h.

Enter the following menus: Powertrain / Engine / Trouble Codes.


i.

Confirm that the DTC is not output again.


Result:
Proceed to
NEXT



NEXT

15.PERFORM ACTIVE TEST USING GTS (CONTROL THE VN TURBO POSITION)
29.REPLACE NO. 5 EXHAUST GAS TEMPERATURE SENSOR
a.

Replace the No. 5 exhaust gas temperature sensor.

Click hereEngine / Hybrid System>N04C-WA (EMISSION CONTROL)>EXHAUST GAS TEMPERATURE SENSOR>REMOVAL


Result:
Proceed to
NEXT



NEXT

14.PERFORM ACTIVE TEST USING GTS (CONTROL THE EGR VALVE POSITION)
30.REPAIR OR REPLACE NO. 5 EXHAUST GAS TEMPERATURE SENSOR
a.

Repair or replace the No. 5 exhaust gas temperature sensor.

HINT:

Clean the sensing unit and install it properly.

If damaged, replace the No. 5 exhaust gas temperature sensor.



Result:
Proceed to
NEXT



NEXT

13.INSPECT NO. 5 EXHAUST GAS TEMPERATURE SENSOR
31.CONNECT SECURELY
a.

Connect securely the No. 5 exhaust gas temperature sensor connector.

HINT:

Repair it as needed.



Result:
Proceed to
NEXT



NEXT

12.CHECK NO. 5 EXHAUST GAS TEMPERATURE SENSOR
32.REPLACE MASS AIR FLOW METER (INTAKE AIR TEMPERATURE SENSOR)
a.

Replace the intake air temperature sensor (built into mass air flow meter).

Click hereEngine / Hybrid System>N04C-WA (ENGINE CONTROL)>MASS AIR FLOW METER>REMOVAL


Result:
Proceed to
NEXT



NEXT

20.CHECK DTC OUTPUT
33.REPAIR OR REPLACE MASS AIR FLOW METER (INTAKE AIR TEMPERATURE SENSOR)
a.

Repair or replace the intake air temperature sensor (built into mass air flow meter).

HINT:

Clean the sensing unit and install it properly.

If damaged, replace the mass air flow meter.



Result:
Proceed to
NEXT



NEXT

34.CHECK DTC OUTPUT
34.CHECK DTC OUTPUT
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Clear the DTCs.

HINT:

Clear the DTCs with the engine stopped, as DTCs cannot be cleared while the engine is running.



d.

Start the engine and warm it up until the engine coolant temperature reaches 60°C (140°F) or higher.


e.

Turn the ignition switch off for 30 seconds or more.


f.

Perform the confirmation driving pattern.


g.

Turn the GTS on.


h.

Enter the following menus: Powertrain / Engine / Trouble Codes.


i.

Confirm that the DTC is not output again.


Result:
Proceed to
NEXT



NEXT

10.INSPECT MASS AIR FLOW METER (INTAKE AIR TEMPERATURE SENSOR)
35.REPLACE ENGINE COOLANT TEMPERATURE SENSOR
a.

Result:
Proceed to
NEXT



NEXT

36.CHECK DTC OUTPUT
36.CHECK DTC OUTPUT
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Clear the DTCs.

HINT:

Clear the DTCs with the engine stopped, as DTCs cannot be cleared while the engine is running.



d.

Start the engine and warm it up until the engine coolant temperature reaches 60°C (140°F) or higher.


e.

Turn the ignition switch off for 30 seconds or more.


f.

Perform the confirmation driving pattern.


g.

Turn the GTS on.


h.

Enter the following menus: Powertrain / Engine / Trouble Codes.


i.

Confirm that the DTC is not output again.


Result:
Proceed to
NEXT



NEXT

9.CHECK MASS AIR FLOW METER (INTAKE AIR TEMPERATURE SENSOR)
37.REPAIR OR REPLACE ENGINE COOLANT TEMPERATURE SENSOR
a.

Repair or replace the engine coolant temperature sensor.

HINT:

Clean the sensing unit and install it properly.

If damaged, replace the engine coolant temperature sensor.



Result:
Proceed to
NEXT



NEXT

38.CHECK DTC OUTPUT
38.CHECK DTC OUTPUT
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Clear the DTCs.

HINT:

Clear the DTCs with the engine stopped, as DTCs cannot be cleared while the engine is running.



d.

Start the engine and warm it up until the engine coolant temperature reaches 60°C (140°F) or higher.


e.

Turn the ignition switch off for 30 seconds or more.


f.

Perform the confirmation driving pattern.


g.

Turn the GTS on.


h.

Enter the following menus: Powertrain / Engine / Trouble Codes.


i.

Confirm that the DTC is not output again.


Result:
Proceed to
NEXT



NEXT

8.CHECK READ VALUE USING GTS (ENGINE COOLANT TEMPERATURE)
39.REPLACE MANIFOLD ABSOLUTE PRESSURE SENSOR
a.

Result:
Proceed to
NEXT



NEXT

40.CHECK DTC OUTPUT
40.CHECK DTC OUTPUT
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Clear the DTCs.

HINT:

Clear the DTCs with the engine stopped, as DTCs cannot be cleared while the engine is running.



d.

Start the engine and warm it up until the engine coolant temperature reaches 60°C (140°F) or higher.


e.

Turn the ignition switch off for 30 seconds or more.


f.

Perform the confirmation driving pattern.


g.

Turn the GTS on.


h.

Enter the following menus: Powertrain / Engine / Trouble Codes.


i.

Confirm that the DTC is not output again.


Result:
Proceed to
NEXT



NEXT

7.CHECK ENGINE COOLANT TEMPERATURE SENSOR
41.REPLACE MANIFOLD ABSOLUTE PRESSURE SENSOR
a.

If dirt, clogging or damage was found in sensing unit, replace the manifold absolute pressure sensor.


Result:
Proceed to
NEXT



NEXT

42.CHECK DTC OUTPUT
42.CHECK DTC OUTPUT
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Clear the DTCs.

HINT:

Clear the DTCs with the engine stopped, as DTCs cannot be cleared while the engine is running.



d.

Start the engine and warm it up until the engine coolant temperature reaches 60°C (140°F) or higher.


e.

Turn the ignition switch off for 30 seconds or more.


f.

Perform the confirmation driving pattern.


g.

Turn the GTS on.


h.

Enter the following menus: Powertrain / Engine / Trouble Codes.


i.

Confirm that the DTC is not output again.


Result:
Proceed to
NEXT



NEXT

6.CHECK READ VALUE USING GTS (ACTUAL BOOST PRESSURE)
43.REPLACE CRANKSHAFT POSITION SENSOR
a.

Result:
Proceed to
NEXT



NEXT

44.CHECK DTC OUTPUT
44.CHECK DTC OUTPUT
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Clear the DTCs.

HINT:

Clear the DTCs with the engine stopped, as DTCs cannot be cleared while the engine is running.



d.

Start the engine and warm it up until the engine coolant temperature reaches 60°C (140°F) or higher.


e.

Turn the ignition switch off for 30 seconds or more.


f.

Perform the confirmation driving pattern.


g.

Turn the GTS on.


h.

Enter the following menus: Powertrain / Engine / Trouble Codes.


i.

Confirm that the DTC is not output again.


Result:
Proceed to
NEXT



NEXT

5.CHECK MANIFOLD ABSOLUTE PRESSURE SENSOR
45.CONNECT SECURELY
a.

Connect securely.

HINT:

Repair it as needed.



Result:
Proceed to
NEXT



NEXT

20.CHECK DTC OUTPUT
46.REPLACE MONOLITHIC CONVERTER ASSEMBLY
a.

Replace the monolithic converter assembly.

Click hereEngine / Hybrid System>N04C-WA (EMISSION CONTROL)>MONOLITHIC CONVERTER>REMOVAL


Result:
Proceed to
NEXT



NEXT

47.REPLACE PARTICULATE MATTER SENSOR
47.REPLACE PARTICULATE MATTER SENSOR
a.

Result:
Proceed to
NEXT



NEXT

48.CHECK DTC OUTPUT
48.CHECK DTC OUTPUT
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Clear the DTCs.

HINT:

Clear the DTCs with the engine stopped, as DTCs cannot be cleared while the engine is running.



d.

Start the engine and warm it up until the engine coolant temperature reaches 60°C (140°F) or higher.


e.

Turn the ignition switch off for 30 seconds or more.


f.

Perform the confirmation driving pattern.


g.

Turn the GTS on.


h.

Enter the following menus: Powertrain / Engine / Trouble Codes.


i.

Confirm that the DTC is not output again.


Result:
Proceed to
NEXT



NEXT

3.INSPECT PARTICULATE MATTER SENSOR CONNECTOR