Home › Engine / Hybrid System › N04C-WA (ENGINE CONTROL) › ECD SYSTEM › from 2019.08
RM2850E _51 Engine / Hybrid System _082611 N04C-WA ENGINE CONTROL _0399963 ECD SYSTEM C

N04C-WA ENGINE CONTROL  ECD SYSTEM  P203F  Reductant Level Too Low  


DESCRIPTION

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P203F Reductant Level Too Low Diagnosis Condition:

Ignition switch ON


Malfunction Status:

Remaining urea solution level 5% or less.


·

Level sensor (Urea pump)

·

Urea tank sub-assembly


- DTC stored

MONITOR DESCRIPTION

The amount of urea solution remaining in the tank is detected to the 10% level by the tank level sensor, and in the 10% to 0% range, the amount of urea solution to be added is calculated and detected in the ECM.

CONFIRMATION DRIVING PATTERN

DTC No. DTC Detection Drive Pattern
P203F Ignition switch ON


CAUTION / NOTICE / HINT

NOTICE:

After replacing the ECM, the new ECM needs registration (Click hereEngine / Hybrid System>N04C-WA (ENGINE CONTROL)>ECD SYSTEM>REGISTRATION) and initialization (Click hereEngine / Hybrid System>N04C-WA (ENGINE CONTROL)>ECD SYSTEM>INITIALIZATION).


HINT:

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.


PROCEDURE

1.CHECK OTHER DTC OUTPUT (UREA SELECTIVE CATALYTIC REDUCTION SYSTEM)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Enter the following menus: Powertrain / Urea Selective Catalytic Reduction / Trouble Codes.


d.

Read the DTCs.


Result:
Result Proceed to
DTC P203B64 is not output A
DTC P203B64 is output B



A

2.INSPECT UREA TANK SUB-ASSEMBLY

B

GO TO DTC P203B64 (UREA SELECTIVE CATALYTIC REDUCTION SYSTEM)

2.INSPECT UREA TANK SUB-ASSEMBLY
a.

Fill the urea tank sub-assembly to with at least 6 liters of urea solution.

OK:

Urea solution gauge display of combination meter increases.



Result:
Proceed to
OK
NG



OK

3.CHECK DTC OUTPUT

NG

4.INSPECT UREA PUMP CONNECTOR
3.CHECK DTC OUTPUT
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Clear the DTCs.

HINT:

Clear the DTCs with the engine stopped, as DTCs cannot be cleared while the engine is running.



d.

Turn the ignition switch off for 30 seconds or more.


e.

Perform the confirmation driving pattern.


f.

Turn the GTS on.


g.

Enter the following menus: Powertrain / Engine / Trouble Codes.


h.

Confirm that the DTC is not output again.


Result:
Proceed to
NEXT



NEXT

END

4.INSPECT UREA PUMP CONNECTOR
a.

Check the connector connection for the urea pump connector.

Standard:

The connector is connected securely and there are no contact pressure problems.



Result:
Proceed to
OK
NG



OK

5.CHECK UREA PUMP (LEVEL SENSOR)

NG

9.CONNECT SECURELY
5.CHECK UREA PUMP (LEVEL SENSOR)
a.

Check if the level sensor float is disconnected, stuck, or damaged.

Click hereEngine / Hybrid System>N04C-WA (EMISSION CONTROL)>UREA PUMP>INSPECTION


Result:
Proceed to
OK
NG



OK

6.CHECK DTC OUTPUT

NG

8.REPLACE UREA PUMP
6.CHECK DTC OUTPUT
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Clear the DTCs.

HINT:

Clear the DTCs with the engine stopped, as DTCs cannot be cleared while the engine is running.



d.

Turn the ignition switch off for 30 seconds or more.


e.

Perform the confirmation driving pattern.


f.

Turn the GTS on.


g.

Enter the following menus: Powertrain / Engine / Trouble Codes.


h.

Read Current DTCs.

Result:
Result Proceed to
DTC P203F is output A
DTCs are not output B




A

7.REPLACE ECM

B

END

7.REPLACE ECM

Result:
Proceed to
NEXT



NEXT

3.CHECK DTC OUTPUT
8.REPLACE UREA PUMP

Result:
Proceed to
NEXT



NEXT

3.CHECK DTC OUTPUT
9.CONNECT SECURELY
a.

Connect securely the urea pump connector.

HINT:

Repair it as needed.



Result:
Proceed to
NEXT



NEXT

3.CHECK DTC OUTPUT