Home › Engine / Hybrid System › N04C-WA (EMISSION CONTROL) › UREA SELECTIVE CATALYTIC REDUCTION SYSTEM › from 2019.08
RM2850E _51 Engine / Hybrid System _082614 N04C-WA EMISSION CONTROL _0400651 UREA SELECTIVE CATALYTIC REDUCTION SYSTEM C

N04C-WA EMISSION CONTROL  UREA SELECTIVE CATALYTIC REDUCTION SYSTEM  P204811  Reductant Injection Valve Circuit Low Bank 1 Unit 1 Circuit Short to Ground  


DESCRIPTION

The urea injector assembly is controlled by the DCU (emission control ECU assembly).

The DCU (emission control ECU assembly) detects abnormality in the sensor by the current of the urea injector assembly circuit.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Warning Indicate Memory
P204811 Reductant Injection Valve Circuit Low Bank 1 Unit 1 Circuit Short to Ground Diagnosis Condition:
·

During operation of the urea injector assembly.


Malfunction Status:
·

The urea injector assembly current is below 0.107 A.


Malfunction Duration:
·

0.2 seconds or more.


·

Open or short in urea injector assembly circuit

·

Urea injector assembly

·

DCU (emission control ECU assembly)


Class A AdBlue consumption warning light:
Comes on
DTC stored

MONITOR DESCRIPTION

Description of malfunction

Low current abnormality is detected in the urea injector assembly.


Reset condition

Procedure to turn off MIL and AdBlue consumption warning light by returning system to normal.

With the urea solution not frozen, start the engine.

When the exhaust gas temperature is 160°C (320°F) or more, the urea SCR system starts and diagnosis of the urea pump and urea injector assembly is performed. After diagnosis is complete, stop the engine.

Repeat the above procedure 3 times.

When the urea SCR system determines that it is normal after starting 1 time, the illuminated MIL remains illuminated and the AdBlue consumption warning light turns off. When the urea SCR system determines that it is normal after starting 3 times, the MIL turns off.


Procedure to turn off MIL and AdBlue consumption warning light after repairs.

After repairs are complete, connect the GTS and clear* the urea SCR system DTCs.

When the engine starts, check that the MIL illuminates and the AdBlue consumption warning light turns off. After 1 minute elapses, stop the engine. Start the engine again and check that the MIL turns off and the system returns to normal.

(*: The ECM malfunction information is not cleared, even if the urea SCR system DTCs are cleared. However, the command that caused the MIL to continuously illuminate is cleared.)



CONFIRMATION DRIVING PATTERN

DTC No. DTC Detection Drive Pattern
P204811 Perform forced operation of the "Control the Reductant Injector Duty Ratio" Active Test at 50% for 1 second or more.

CAUTION / NOTICE / HINT

HINT:

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.


PROCEDURE

1.CHECK CONNECTOR CONNECTION CONDITION (UREA INJECTOR ASSEMBLY)
a.

Check the connector connection and contact pressure of the urea injector assembly connector.

OK:

The connector is connected securely and there are no contact pressure problems.



Result:
Proceed to
OK
NG



OK

2.INSPECT UREA INJECTOR ASSEMBLY

NG

11.CONNECT SECURELY
2.INSPECT UREA INJECTOR ASSEMBLY
a.

Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (UREA INJECTOR ASSEMBLY - DCU (EMISSION CONTROL ECU ASSEMBLY))

NG

10.REPLACE UREA INJECTOR ASSEMBLY
3.CHECK HARNESS AND CONNECTOR (UREA INJECTOR ASSEMBLY - DCU (EMISSION CONTROL ECU ASSEMBLY))
a.
A405886C01
1.51,0.125 1.885,0.406 0.375,0.281 0.083,0.115 0.396,0.313 0.313,0.198 10 false *a 1.667,0.208 1.979,0.406 0.313,0.198 10 false E
*a Signal Check Harness No. 2 Lead Connector


Connect the signal check harness No. 2 to the DCU (emission control ECU assembly) vehicle side harness. (Do not connect the harness to the DCU (emission control ECU assembly).)


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
E-6 (UIV+) - Body ground Ignition switch off 10 kΩ or higher
E-7 (UIV-) - Body ground Ignition switch off 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

4.CHECK HARNESS AND CONNECTOR (UREA INJECTOR ASSEMBLY - DCU (EMISSION CONTROL ECU ASSEMBLY))

NG

9.REPAIR OR REPLACE HARNESS OR CONNECTOR
4.CHECK HARNESS AND CONNECTOR (UREA INJECTOR ASSEMBLY - DCU (EMISSION CONTROL ECU ASSEMBLY))
a.
A405886C01
1.51,0.125 1.885,0.406 0.375,0.281 0.083,0.115 0.396,0.313 0.313,0.198 10 false *a 1.667,0.208 1.979,0.406 0.313,0.198 10 false E
*a Signal Check Harness No. 2 Lead Connector


Connect the urea injector assembly connector.


b.

Connect the signal check harness No. 2 to the DCU (emission control ECU assembly) vehicle side harness. (Do not connect the harness to the DCU (emission control ECU assembly).)


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
E-6 (UIV+) -E-7 (UIV-) Ignition switch off 17 Ω or less



Result:
Proceed to
OK
NG



OK

5.CLEAR DTC

NG

8.REPAIR OR REPLACE HARNESS OR CONNECTOR
5.CLEAR DTC
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Clear the DTCs.

NOTICE:

Clear the DTCs with the engine stopped, as DTCs cannot be cleared while the engine is running.



e.

Turn the ignition switch off and wait for at least 30 seconds.


Result:
Proceed to
NEXT



NEXT

6.CHECK WHETHER DTC OUTPUT RECURS (DTC P204811)
6.CHECK WHETHER DTC OUTPUT RECURS (DTC P204811)
a.

Drive the vehicle in accordance with the driving pattern described in the Confirmation Driving Pattern.


b.

Connect the GTS to the DLC3.


c.

Turn the ignition switch to ON.


d.

Turn the GTS on.


e.

Enter the following menus: Powertrain / Urea Selective Catalytic Reduction / Trouble Codes.


f.

Read the DTCs.

Result:
Result Proceed to
DTC P204811 is output A
DTCs are not output B




A

7.REPLACE DCU (EMISSION CONTROL ECU ASSEMBLY)

B

END

7.REPLACE DCU (EMISSION CONTROL ECU ASSEMBLY)
a.

Replace the DCU (emission control ECU assembly).

Click hereEngine / Hybrid System>N04C-WA (EMISSION CONTROL)>UREA PUMP CONTROL ECU>REMOVAL

HINT:

Perform DPR forced regeneration after DCU (emission control ECU assembly) replacement.

Click hereEngine / Hybrid System>N04C-WA (EMISSION CONTROL)>EMISSION CONTROL SYSTEM>ON-VEHICLE INSPECTION



Result:
Proceed to
NEXT



NEXT

12.CLEAR DTC
8.REPAIR OR REPLACE HARNESS OR CONNECTOR
a.

Repair or replace the harness or connector.


Result:
Proceed to
NEXT



NEXT

12.CLEAR DTC
9.REPAIR OR REPLACE HARNESS OR CONNECTOR
a.

Repair or replace the harness or connector.


Result:
Proceed to
NEXT



NEXT

12.CLEAR DTC
10.REPLACE UREA INJECTOR ASSEMBLY
a.

Replace the urea injector assembly.

Click hereEngine / Hybrid System>N04C-WA (EMISSION CONTROL)>UREA INJECTOR>REMOVAL


Result:
Proceed to
NEXT



NEXT

12.CLEAR DTC
11.CONNECT SECURELY
a.

Securely connect the urea injector assembly connector.

HINT:

Repair parts as necessary.



Result:
Proceed to
NEXT



NEXT

12.CLEAR DTC
12.CLEAR DTC
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Clear the DTCs.

NOTICE:

Clear the DTCs with the engine stopped, as DTCs cannot be cleared while the engine is running.



e.

Turn the ignition switch off and wait for at least 30 seconds.


Result:
Proceed to
NEXT



NEXT

13.CHECK WHETHER DTC OUTPUT RECURS (DTC P204811)
13.CHECK WHETHER DTC OUTPUT RECURS (DTC P204811)
a.

Drive the vehicle in accordance with the driving pattern described in the Confirmation Driving Pattern.


b.

Connect the GTS to the DLC3.


c.

Turn the ignition switch to ON.


d.

Turn the GTS on.


e.

Enter the following menus: Powertrain / Urea Selective Catalytic Reduction / Trouble Codes.


f.

Read the DTCs.

OK:

DTCs are not output



Result:
Proceed to
NEXT



NEXT

END