Home › Engine / Hybrid System › N04C-WA (EMISSION CONTROL) › UREA SELECTIVE CATALYTIC REDUCTION SYSTEM › from 2019.08
RM2850E _51 Engine / Hybrid System _082614 N04C-WA EMISSION CONTROL _0400651 UREA SELECTIVE CATALYTIC REDUCTION SYSTEM C

N04C-WA EMISSION CONTROL  UREA SELECTIVE CATALYTIC REDUCTION SYSTEM  P208D15  Reductant Pump "A" Control Circuit High Circuit Short to Battery or Open  


DESCRIPTION

The DCU (emission control ECU assembly) determines failure of the urea pump motor based on the urea pump motor voltage.

The pump is actuated by the energization to the 3-phase alternate current motor.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Warning Indicate Memory
P208D15 Reductant Pump "A" Control Circuit High Circuit Short to Battery or Open Diagnosis Condition:
·

Ignition switch ON.

·

Pump driver is on.


Malfunction Status:
·

The pump motor voltage is higher than 0.562 V.


Malfunction Duration:
·

3 times.


·

Open or short in urea pump circuit

·

Urea pump

·

DCU (emission control ECU assembly)


Class A AdBlue consumption warning light:
Comes on
DTC stored

MONITOR DESCRIPTION

Description of malfunction

Motor malfunction of urea pump is detected.


Reset condition

After having restored to the normal conditions.


CONFIRMATION DRIVING PATTERN

DTC No. DTC Detection Drive Pattern
P208D15 Perform the "Reductant Pump Speed Check" Utility.

WIRING DIAGRAM

·

For the circuit diagram of the pump motor (urea pump) refer to the DTC P208C11.

Click hereEngine / Hybrid System>N04C-WA (EMISSION CONTROL)>UREA SELECTIVE CATALYTIC REDUCTION SYSTEM>P208C11

·

For the circuit diagram of the DCU (emission control ECU assembly) power source refer to the DTC P0562A2.

Click hereEngine / Hybrid System>N04C-WA (EMISSION CONTROL)>UREA SELECTIVE CATALYTIC REDUCTION SYSTEM>P0562A2

·

For the circuit diagram of the VCPU terminal refer to the DTC P0642A2.

Click hereEngine / Hybrid System>N04C-WA (EMISSION CONTROL)>UREA SELECTIVE CATALYTIC REDUCTION SYSTEM>P0642A2

·

For the circuit diagram of the VCLU terminal refer to the DTC P0652A2.

Click hereEngine / Hybrid System>N04C-WA (EMISSION CONTROL)>UREA SELECTIVE CATALYTIC REDUCTION SYSTEM>P0652A2


CAUTION / NOTICE / HINT

HINT:

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.


PROCEDURE

1.CHECK CONNECTOR CONNECTION CONDITION (UREA PUMP)
a.

Check the connector connection and contact pressure of the urea pump connector.

OK:

The connector is connected securely and there are no contact pressure problems.



Result:
Proceed to
OK
NG



OK

2.CHECK CONNECTOR CONNECTION CONDITION (DCU (EMISSION CONTROL ECU ASSEMBLY))

NG

14.CONNECT SECURELY
2.CHECK CONNECTOR CONNECTION CONDITION (DCU (EMISSION CONTROL ECU ASSEMBLY))
a.

Check the connector connection and contact pressure of the DCU (emission control ECU assembly) connector.

OK:

The connector is connected securely and there are no contact pressure problems.



Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (UREA PUMP - DCU (EMISSION CONTROL ECU ASSEMBLY))

NG

13.CONNECT SECURELY
3.CHECK HARNESS AND CONNECTOR (UREA PUMP - DCU (EMISSION CONTROL ECU ASSEMBLY))
a.
A405886C01
1.51,0.125 1.885,0.406 0.375,0.281 0.083,0.115 0.396,0.313 0.313,0.198 10 false *a 1.667,0.208 1.979,0.406 0.313,0.198 10 false E
*a Signal Check Harness No. 2 Lead Connector


A405887C01
1.521,0.125 1.885,0.396 0.365,0.271 0.073,0.104 0.385,0.302 0.313,0.198 10 false *a 1.677,0.198 1.833,0.396 0.156,0.198 10 false E
*a Signal Check Harness No. 2 Lead Connector


Disconnect the urea pump connector.


b.

Connect the signal check harness No. 2 to the DCU (emission control ECU assembly) vehicle side harness. (Do not connect the harness to the DCU (emission control ECU assembly).)


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
E-1 (UPMU) - E-17 (+BU1) Ignition switch off 10 kΩ or higher
E-1 (UPMU) - E-18 (+BU2) Ignition switch off 10 kΩ or higher
E-1 (UPMU) - E-19 (+BU3) Ignition switch off 10 kΩ or higher
E-1 (UPMU) - E-33 (+BU4) Ignition switch off 10 kΩ or higher
E-1 (UPMU) - E-51 (+BU5) Ignition switch off 10 kΩ or higher
E-1 (UPMU) - E-52 (PB3) Ignition switch off 10 kΩ or higher
E-1 (UPMU) - E-24 (VCLU) Ignition switch off 10 kΩ or higher
E-1 (UPMU) - E-25 (VCPU) Ignition switch off 10 kΩ or higher
E-1 (UPMU) - E-30 (BATT) Ignition switch off 10 kΩ or higher
E-20 (UPMV) - E-17 (+BU1) Ignition switch off 10 kΩ or higher
E-20 (UPMV) - E-18 (+BU2) Ignition switch off 10 kΩ or higher
E-20 (UPMV) - E-19 (+BU3) Ignition switch off 10 kΩ or higher
E-20 (UPMV) - E-33 (+BU4) Ignition switch off 10 kΩ or higher
E-20 (UPMV) - E-51 (+BU5) Ignition switch off 10 kΩ or higher
E-20 (UPMV) - E-52 (PB3) Ignition switch off 10 kΩ or higher
E-20 (UPMV) - E-24 (VCLU) Ignition switch off 10 kΩ or higher
E-20 (UPMV) - E-25 (VCPU) Ignition switch off 10 kΩ or higher
E-20 (UPMV) - E-30 (BATT) Ignition switch off 10 kΩ or higher
E-31 (UPMW) - E-17 (+BU1) Ignition switch off 10 kΩ or higher
E-31 (UPMW) - E-18 (+BU2) Ignition switch off 10 kΩ or higher
E-31 (UPMW) - E-19 (+BU3) Ignition switch off 10 kΩ or higher
E-31 (UPMW) - E-33 (+BU4) Ignition switch off 10 kΩ or higher
E-31 (UPMW) - E-51 (+BU5) Ignition switch off 10 kΩ or higher
E-31 (UPMW) - E-52 (PB3) Ignition switch off 10 kΩ or higher
E-31 (UPMW) - E-24 (VCLU) Ignition switch off 10 kΩ or higher
E-31 (UPMW) - E-25 (VCPU) Ignition switch off 10 kΩ or higher
E-31 (UPMW) - E-30 (BATT) Ignition switch off 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

4.CHECK HARNESS AND CONNECTOR (UREA PUMP - DCU (EMISSION CONTROL ECU ASSEMBLY))

NG

12.REPAIR OR REPLACE HARNESS OR CONNECTOR
4.CHECK HARNESS AND CONNECTOR (UREA PUMP - DCU (EMISSION CONTROL ECU ASSEMBLY))
a.
A405886C01
1.51,0.125 1.885,0.406 0.375,0.281 0.083,0.115 0.396,0.313 0.313,0.198 10 false *a 1.667,0.208 1.979,0.406 0.313,0.198 10 false E
*a Signal Check Harness No. 2 Lead Connector


A360358C16
1.479,0.833 1.896,1.094 0.417,0.26 1.229,1.844 1.156,2.813 true 1.406,1.625 1.865,2.802 true 1.188,1.625 0.521,2.823 true 0.146,0.177 0.458,0.375 0.313,0.198 10 false *a 1.573,0.896 1.885,1.094 0.313,0.198 10 false P11 1.75,2.833 2.49,3.031 0.74,0.198 10 false UPMU 0.969,2.844 1.531,3.052 0.563,0.208 10 false UPMW 0.271,2.844 0.833,3.052 0.563,0.208 10 false UPMV
*a Front view of wire harness connector
(to Urea Pump)


Disconnect the urea pump connector.


b.

Connect the signal check harness No. 2 to the DCU (emission control ECU assembly) vehicle side harness. (Do not connect the harness to the DCU (emission control ECU assembly).)


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
E-1 (UPMU) - P11-7 (UPMU) Ignition switch off Below 1 Ω
E-20 (UPMV) - P11-8 (UPMV) Ignition switch off Below 1 Ω
E-31 (UPMW) - P11-16 (UPMW) Ignition switch off Below 1 Ω



Result:
Proceed to
OK
NG



OK

5.CHECK HARNESS AND CONNECTOR (UREA PUMP - DCU (EMISSION CONTROL ECU ASSEMBLY))

NG

11.REPAIR OR REPLACE HARNESS OR CONNECTOR
5.CHECK HARNESS AND CONNECTOR (UREA PUMP - DCU (EMISSION CONTROL ECU ASSEMBLY))
a.
A405886C01
1.51,0.125 1.885,0.406 0.375,0.281 0.083,0.115 0.396,0.313 0.313,0.198 10 false *a 1.667,0.208 1.979,0.406 0.313,0.198 10 false E
*a Signal Check Harness No. 2 Lead Connector


Connect the signal check harness No. 2 to the DCU (emission control ECU assembly) vehicle side harness. (Do not connect the harness to the DCU (emission control ECU assembly).)


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
E-1 (UPMU) - Body ground Ignition switch off 10 kΩ or higher
E-20 (UPMV) - Body ground Ignition switch off 10 kΩ or higher
E-31 (UPMW) - Body ground Ignition switch off 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

6.REPLACE UREA PUMP

NG

10.REPAIR OR REPLACE HARNESS OR CONNECTOR
6.REPLACE UREA PUMP

Result:
Proceed to
NEXT



NEXT

7.CLEAR DTC
7.CLEAR DTC
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Clear the DTCs.

NOTICE:

Clear the DTCs with the engine stopped, as DTCs cannot be cleared while the engine is running.



e.

Turn the ignition switch off and wait for at least 30 seconds.


Result:
Proceed to
NEXT



NEXT

8.CHECK WHETHER DTC OUTPUT RECURS (DTC P208D15)
8.CHECK WHETHER DTC OUTPUT RECURS (DTC P208D15)
a.

Drive the vehicle in accordance with the driving pattern described in the Confirmation Driving Pattern.


b.

Connect the GTS to the DLC3.


c.

Turn the ignition switch to ON.


d.

Turn the GTS on.


e.

Enter the following menus: Powertrain / Urea Selective Catalytic Reduction / Trouble Codes.


f.

Read the DTCs.

Result:
Result Proceed to
DTC P208D15 is output A
DTCs are not output B




A

9.REPLACE DCU (EMISSION CONTROL ECU ASSEMBLY)

B

END

9.REPLACE DCU (EMISSION CONTROL ECU ASSEMBLY)
a.

Replace the DCU (emission control ECU assembly).

Click hereEngine / Hybrid System>N04C-WA (EMISSION CONTROL)>UREA PUMP CONTROL ECU>REMOVAL


Result:
Proceed to
NEXT



NEXT

15.CLEAR DTC
10.REPAIR OR REPLACE HARNESS OR CONNECTOR
a.

Repair or replace the harness or connector.


Result:
Proceed to
NEXT



NEXT

15.CLEAR DTC
11.REPAIR OR REPLACE HARNESS OR CONNECTOR
a.

Repair or replace the harness or connector.


Result:
Proceed to
NEXT



NEXT

15.CLEAR DTC
12.REPAIR OR REPLACE HARNESS OR CONNECTOR
a.

Repair or replace the harness or connector.


Result:
Proceed to
NEXT



NEXT

15.CLEAR DTC
13.CONNECT SECURELY
a.

Securely connect the DCU (emission control ECU assembly) connector.

HINT:

Repair parts as necessary.



Result:
Proceed to
NEXT



NEXT

15.CLEAR DTC
14.CONNECT SECURELY
a.

Securely connect the urea pump connector.

HINT:

Repair parts as necessary.



Result:
Proceed to
NEXT



NEXT

15.CLEAR DTC
15.CLEAR DTC
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Clear the DTCs.

NOTICE:

Clear the DTCs with the engine stopped, as DTCs cannot be cleared while the engine is running.



e.

Turn the ignition switch off and wait for at least 30 seconds.


Result:
Proceed to
NEXT



NEXT

16.CHECK WHETHER DTC OUTPUT RECURS (DTC P208D15)
16.CHECK WHETHER DTC OUTPUT RECURS (DTC P208D15)
a.

Drive the vehicle in accordance with the driving pattern described in the Confirmation Driving Pattern.


b.

Connect the GTS to the DLC3.


c.

Turn the ignition switch to ON.


d.

Turn the GTS on.


e.

Enter the following menus: Powertrain / Urea Selective Catalytic Reduction / Trouble Codes.


f.

Read the DTCs.

OK:

DTCs are not output



Result:
Proceed to
NEXT



NEXT

END