The DCU (emission control ECU assembly) determines failure of the urea pump based on the pump motor voltage.
The urea pump is actuated by the energization to the 3-phase alternate current motor.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | MIL | Warning Indicate | Memory |
|---|---|---|---|---|---|---|
| P208C11 | Reductant Pump "A" Control Circuit Low Circuit Short to Ground | Diagnosis Condition:
·
Ignition switch ON. ·
Pump driver is off. Malfunction Status: ·
The pump motor voltage is less than 0.562 V. Malfunction Duration: ·
3 times. |
·
Open or short in urea pump circuit ·
Urea pump ·
DCU (emission control ECU assembly) |
Class A | AdBlue consumption warning light:
Comes on |
DTC stored |
Motor malfunction of urea pump is detected.
After having restored to the normal conditions.
| DTC No. | DTC Detection Drive Pattern |
|---|---|
| P208C11 | Perform the "Reductant Pump Speed Check" Utility. |
Pump motor (urea pump) circuit.
For the circuit diagram of the SGN4 terminal refer to the DTC P007162.
Click hereEngine / Hybrid System>N04C-WA (EMISSION CONTROL)>UREA SELECTIVE CATALYTIC REDUCTION SYSTEM>P007162
For the circuit diagram of the EPU terminal refer to the DTC P0642A2.
Click hereEngine / Hybrid System>N04C-WA (EMISSION CONTROL)>UREA SELECTIVE CATALYTIC REDUCTION SYSTEM>P0642A2
For the circuit diagram of the ELU terminal refer to the DTC P0652A2.
Click hereEngine / Hybrid System>N04C-WA (EMISSION CONTROL)>UREA SELECTIVE CATALYTIC REDUCTION SYSTEM>P0652A2
For the circuit diagram of the ISG terminal refer to the DTC P202E71.
Click hereEngine / Hybrid System>N04C-WA (EMISSION CONTROL)>UREA SELECTIVE CATALYTIC REDUCTION SYSTEM>P202E71
For the circuit diagram of the ETHU terminal refer to the DTC P205B62.
Click hereEngine / Hybrid System>N04C-WA (EMISSION CONTROL)>UREA SELECTIVE CATALYTIC REDUCTION SYSTEM>P205B62
For the circuit diagram of the MSG terminal refer to the DTC P208C11.
Click hereEngine / Hybrid System>N04C-WA (EMISSION CONTROL)>UREA SELECTIVE CATALYTIC REDUCTION SYSTEM>P208C11
Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.
Check the connector connection and contact pressure of the urea pump connector.
The connector is connected securely and there are no contact pressure problems.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Check the connector connection and contact pressure of the DCU (emission control ECU assembly) connector.
The connector is connected securely and there are no contact pressure problems.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *a | Signal Check Harness No. 2 Lead Connector |
| *a | Signal Check Harness No. 2 Lead Connector |
Disconnect the urea pump connector.
Connect the signal check harness No. 2 to the DCU (emission control ECU assembly) vehicle side harness. (Do not connect the harness to the DCU (emission control ECU assembly).)
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| E-1 (UPMU) - Body ground | Ignition switch off | 10 kΩ or higher |
| E-20 (UPMV) - Body ground | Ignition switch off | 10 kΩ or higher |
| E-31 (UPMW) - Body ground | Ignition switch off | 10 kΩ or higher |
| E-1 (UPMU) - E-36 (ELU) | Ignition switch off | 10 kΩ or higher |
| E-1 (UPMU) - E-37 (ISG) | Ignition switch off | 10 kΩ or higher |
| E-1 (UPMU) - E-43 (ETHU) | Ignition switch off | 10 kΩ or higher |
| E-1 (UPMU) - E-44 (EPU) | Ignition switch off | 10 kΩ or higher |
| E-1 (UPMU) - E-45 (MSG) | Ignition switch off | 10 kΩ or higher |
| E-1 (UPMU) - E-60 (SGN4) | Ignition switch off | 10 kΩ or higher |
| E-20 (UPMV) - E-36 (ELU) | Ignition switch off | 10 kΩ or higher |
| E-20 (UPMV) - E-37 (ISG) | Ignition switch off | 10 kΩ or higher |
| E-20 (UPMV) - E-43 (ETHU) | Ignition switch off | 10 kΩ or higher |
| E-20 (UPMV) - E-44 (EPU) | Ignition switch off | 10 kΩ or higher |
| E-20 (UPMV) - E-45 (MSG) | Ignition switch off | 10 kΩ or higher |
| E-20 (UPMV) - E-60 (SGN4) | Ignition switch off | 10 kΩ or higher |
| E-31 (UPMW) - E-36 (ELU) | Ignition switch off | 10 kΩ or higher |
| E-31 (UPMW) - E-37 (ISG) | Ignition switch off | 10 kΩ or higher |
| E-31 (UPMW) - E-43 (ETHU) | Ignition switch off | 10 kΩ or higher |
| E-31 (UPMW) - E-44 (EPU) | Ignition switch off | 10 kΩ or higher |
| E-31 (UPMW) - E-45 (MSG) | Ignition switch off | 10 kΩ or higher |
| E-31 (UPMW) - E-60 (SGN4) | Ignition switch off | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *a | Signal Check Harness No. 2 Lead Connector |
| *a | Front view of wire harness connector
(to Urea Pump) |
Disconnect the urea pump connector.
Connect the signal check harness No. 2 to the DCU (emission control ECU assembly) vehicle side harness. (Do not connect the harness to the DCU (emission control ECU assembly).)
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| E-1 (UPMU) - P11-7 (UPMU) | Ignition switch off | Below 1 Ω |
| E-20 (UPMV) - P11-8 (UPMV) | Ignition switch off | Below 1 Ω |
| E-31 (UPMW) - P11-16 (UPMW) | Ignition switch off | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *a | Signal Check Harness No. 2 Lead Connector |
Connect the signal check harness No. 2 to the DCU (emission control ECU assembly) vehicle side harness. (Do not connect the harness to the DCU (emission control ECU assembly).)
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| E-1 (UPMU) - Body ground | Ignition switch off | 10 kΩ or higher |
| E-20 (UPMV) - Body ground | Ignition switch off | 10 kΩ or higher |
| E-31 (UPMW) - Body ground | Ignition switch off | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Replace the urea pump.
Click hereEngine / Hybrid System>N04C-WA (EMISSION CONTROL)>UREA PUMP>REMOVAL
| Proceed to |
|---|
| NEXT |
NEXT
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Clear the DTCs.
Clear the DTCs with the engine stopped, as DTCs cannot be cleared while the engine is running.
Turn the ignition switch off and wait for at least 30 seconds.
| Proceed to |
|---|
| NEXT |
NEXT
Drive the vehicle in accordance with the driving pattern described in the Confirmation Driving Pattern.
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Enter the following menus: Powertrain / Urea Selective Catalytic Reduction / Trouble Codes.
Read the DTCs.
| Result | Proceed to |
|---|---|
| DTC P208C11 is output | A |
| DTCs are not output | B |
A
B
Replace the DCU (emission control ECU assembly).
Click hereEngine / Hybrid System>N04C-WA (EMISSION CONTROL)>UREA PUMP CONTROL ECU>REMOVAL
| Proceed to |
|---|
| NEXT |
NEXT
Repair or replace the harness or connector.
| Proceed to |
|---|
| NEXT |
NEXT
Repair or replace the harness or connector.
| Proceed to |
|---|
| NEXT |
NEXT
Repair or replace the harness or connector.
| Proceed to |
|---|
| NEXT |
NEXT
Securely connect the DCU (emission control ECU assembly) connector.
Repair parts as necessary.
| Proceed to |
|---|
| NEXT |
NEXT
Securely connect the urea pump connector.
Repair parts as necessary.
| Proceed to |
|---|
| NEXT |
NEXT
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Clear the DTCs.
Clear the DTCs with the engine stopped, as DTCs cannot be cleared while the engine is running.
Turn the ignition switch off and wait for at least 30 seconds.
| Proceed to |
|---|
| NEXT |
NEXT
Drive the vehicle in accordance with the driving pattern described in the Confirmation Driving Pattern.
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Enter the following menus: Powertrain / Urea Selective Catalytic Reduction / Trouble Codes.
Read the DTCs.
DTCs are not output
| Proceed to |
|---|
| NEXT |
NEXT