The tank heater prevents urea solution in the tank freezing.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | MIL | Warning Indicate | Memory |
|---|---|---|---|---|---|---|
| P20C012 | Reductant Heater "B" Control Circuit High Circuit Short to Battery | Diagnosis Condition:
·
Ignition switch ON. Malfunction Status: ·
The tank heater (urea pump) voltage is higher than specified value. Malfunction Duration: ·
3 seconds or more. |
·
Open or short in tank heater (urea pump) circuit ·
Tank heater (urea pump) ·
DCU (emission control ECU assembly) |
Class A | AdBlue consumption warning light:
Comes on |
DTC stored |
High voltage is detected in the tank heater (urea pump).
After having restored to the normal conditions.
| DTC No. | DTC Detection Drive Pattern |
|---|---|
| P20C012 | Ignition switch ON for 3 seconds or more. |
For the circuit diagram of the tank heater (urea pump) refer to the DTC P20BD14.
Click hereEngine / Hybrid System>N04C-WA (EMISSION CONTROL)>UREA SELECTIVE CATALYTIC REDUCTION SYSTEM>P20BD14
For the circuit diagram of the DCU (emission control ECU assembly) power source refer to the DTC P0562A2.
Click hereEngine / Hybrid System>N04C-WA (EMISSION CONTROL)>UREA SELECTIVE CATALYTIC REDUCTION SYSTEM>P0562A2
For the circuit diagram of the VCPU terminal refer to the DTC P0642A2.
Click hereEngine / Hybrid System>N04C-WA (EMISSION CONTROL)>UREA SELECTIVE CATALYTIC REDUCTION SYSTEM>P0642A2
For the circuit diagram of the VCLU terminal refer to the DTC P0652A2.
Click hereEngine / Hybrid System>N04C-WA (EMISSION CONTROL)>UREA SELECTIVE CATALYTIC REDUCTION SYSTEM>P0652A2
Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.
| *a | Signal Check Harness No. 2 Lead Connector |
| *a | Signal Check Harness No. 2 Lead Connector |
Disconnect the tank heater (urea pump) connector.
Connect the signal check harness No. 2 to the DCU (emission control ECU assembly) vehicle side harness. (Do not connect the harness to the DCU (emission control ECU assembly).)
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| E-2 (HTT) - Body ground | Ignition switch off | 10 kΩ or higher |
| E-21 (EHTT) - Body ground | Ignition switch off | 10 kΩ or higher |
| E-2 (HTT) - E-17 (+BU1) | Ignition switch off | 10 kΩ or higher |
| E-2 (HTT) - E-18 (+BU2) | Ignition switch off | 10 kΩ or higher |
| E-2 (HTT) - E-19 (+BU3) | Ignition switch off | 10 kΩ or higher |
| E-2 (HTT) - E-33 (+BU4) | Ignition switch off | 10 kΩ or higher |
| E-2 (HTT) - E-51 (+BU5) | Ignition switch off | 10 kΩ or higher |
| E-2 (HTT) - E-52 (PB3) | Ignition switch off | 10 kΩ or higher |
| E-2 (HTT) - E-24 (VCLU) | Ignition switch off | 10 kΩ or higher |
| E-2 (HTT) - E-25 (VCPU) | Ignition switch off | 10 kΩ or higher |
| E-2 (HTT) - E-30 (BATT) | Ignition switch off | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *a | Component without harness connected
(Tank Heater (Urea Pump)) |
Disconnect the tank heater (urea pump) connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 9 (HTT) - 11 (EHTT) | 25°C | 1.36 to 1.52 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *a | Signal Check Harness No. 2 Lead Connector |
Connect the tank heater (urea pump) connector.
Connect the signal check harness No. 2 to the DCU (emission control ECU assembly) vehicle side harness. (Do not connect the harness to the DCU (emission control ECU assembly).)
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| E-2 (HTT) - E-21 (EHTT) | 25°C | 1.36 to 1.52 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Clear the DTCs.
Clear the DTCs with the engine stopped, as DTCs cannot be cleared while the engine is running.
Turn the ignition switch off and wait for at least 30 seconds.
| Proceed to |
|---|
| NEXT |
NEXT
Drive the vehicle in accordance with the driving pattern described in the Confirmation Driving Pattern.
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Enter the following menus: Powertrain / Urea Selective Catalytic Reduction / Trouble Codes.
Read the DTCs.
| Result | Proceed to |
|---|---|
| DTC P20C012 is output | A |
| DTCs are not output | B |
A
B
Replace the DCU (emission control ECU assembly).
Click hereEngine / Hybrid System>N04C-WA (EMISSION CONTROL)>UREA PUMP CONTROL ECU>REMOVAL
| Proceed to |
|---|
| NEXT |
NEXT
Repair or replace the harness or connector.
| Proceed to |
|---|
| NEXT |
NEXT
Replace the tank heater (urea pump).
Click hereEngine / Hybrid System>N04C-WA (EMISSION CONTROL)>UREA PUMP>REMOVAL
| Proceed to |
|---|
| NEXT |
NEXT
Repair or replace the harness or connector.
| Proceed to |
|---|
| NEXT |
NEXT
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Clear the DTCs.
Clear the DTCs with the engine stopped, as DTCs cannot be cleared while the engine is running.
Turn the ignition switch off and wait for at least 30 seconds.
| Proceed to |
|---|
| NEXT |
NEXT
Drive the vehicle in accordance with the driving pattern described in the Confirmation Driving Pattern.
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Enter the following menus: Powertrain / Urea Selective Catalytic Reduction / Trouble Codes.
Read the DTCs.
DTCs are not output
| Proceed to |
|---|
| NEXT |
NEXT