Home › Engine / Hybrid System › N04C-WA (EMISSION CONTROL) › UREA SELECTIVE CATALYTIC REDUCTION SYSTEM › from 2019.08
RM2850E _51 Engine / Hybrid System _082614 N04C-WA EMISSION CONTROL _0400651 UREA SELECTIVE CATALYTIC REDUCTION SYSTEM C

N04C-WA EMISSION CONTROL  UREA SELECTIVE CATALYTIC REDUCTION SYSTEM  P20BD14  Reductant Heater "B" Control Circuit/Open Circuit Short to Ground or Open  


DESCRIPTION

The tank heater prevents urea solution in the tank freezing.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Warning Indicate Memory
P20BD14 Reductant Heater "B" Control Circuit/Open Circuit Short to Ground or Open Diagnosis Condition:
·

Ignition switch ON.


Malfunction Status:
·

The tank heater (urea pump) voltage is less than specified value.


Malfunction Duration:
·

3 seconds or more.


·

Open or short in tank heater (urea pump) circuit

·

Tank heater (urea pump)

·

DCU (emission control ECU assembly)


Class A AdBlue consumption warning light:
Comes on
DTC stored

MONITOR DESCRIPTION

Description of malfunction

Low voltage is detected in the tank heater (urea pump).


Reset condition

After having restored to the normal conditions.


CONFIRMATION DRIVING PATTERN

DTC No. DTC Detection Drive Pattern
P20BD14 Ignition switch ON for 3 seconds or more.

WIRING DIAGRAM

·

Tank heater (urea pump) circuit.

A444332E03
0.583,2.188 2.604,2.406 2.021,0.219 10 false Tank Heater (Urea Pump) 4.635,2.229 7.146,2.469 2.51,0.24 10 false DCU (Emission Control ECU Assembly) 0.573,2.031 0.885,2.208 0.313,0.177 10 false P11 1.51,1.323 1.885,1.5 0.375,0.177 10 false EHTT 1.583,0.813 1.896,0.99 0.313,0.177 10 false HTT 1.99,0.802 2.302,0.979 0.313,0.177 10 false 9 1.958,1.385 2.271,1.563 0.313,0.177 10 false 11 4.958,0.719 5.271,0.896 0.313,0.177 10 false 2 4.906,1.292 5.219,1.469 0.313,0.177 10 false 21 5.271,0.906 5.583,1.083 0.313,0.177 10 false HTT 5.281,1.51 5.656,1.688 0.375,0.177 10 false EHTT 4.51,0.927 4.823,1.104 0.313,0.177 10 false E-2 4.469,1.51 4.781,1.688 0.313,0.177 10 false E-21 4.865,0.917 5.177,1.094 0.313,0.177 10 false P12 4.865,1.5 5.177,1.677 0.313,0.177 10 false P12

·

For the circuit diagram of the SGN4 terminal refer to the DTC P007162.

Click hereEngine / Hybrid System>N04C-WA (EMISSION CONTROL)>UREA SELECTIVE CATALYTIC REDUCTION SYSTEM>P007162

·

For the circuit diagram of the EPU terminal refer to the DTC P0642A2.

Click hereEngine / Hybrid System>N04C-WA (EMISSION CONTROL)>UREA SELECTIVE CATALYTIC REDUCTION SYSTEM>P0642A2

·

For the circuit diagram of the ELU terminal refer to the DTC P0652A2.

Click hereEngine / Hybrid System>N04C-WA (EMISSION CONTROL)>UREA SELECTIVE CATALYTIC REDUCTION SYSTEM>P0652A2

·

For the circuit diagram of the ISG terminal refer to the DTC P202E71.

Click hereEngine / Hybrid System>N04C-WA (EMISSION CONTROL)>UREA SELECTIVE CATALYTIC REDUCTION SYSTEM>P202E71

·

For the circuit diagram of the ETHU terminal refer to the DTC P205B62.

Click hereEngine / Hybrid System>N04C-WA (EMISSION CONTROL)>UREA SELECTIVE CATALYTIC REDUCTION SYSTEM>P205B62

·

For the circuit diagram of the MSG terminal refer to the DTC P208C11.

Click hereEngine / Hybrid System>N04C-WA (EMISSION CONTROL)>UREA SELECTIVE CATALYTIC REDUCTION SYSTEM>P208C11


CAUTION / NOTICE / HINT

HINT:

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.


PROCEDURE

1.CHECK HARNESS AND CONNECTOR (TANK HEATER (UREA PUMP) - DCU (EMISSION CONTROL ECU ASSEMBLY))
a.
A405886C01
1.51,0.125 1.885,0.406 0.375,0.281 0.083,0.115 0.396,0.313 0.313,0.198 10 false *a 1.667,0.208 1.979,0.406 0.313,0.198 10 false E
*a Signal Check Harness No. 2 Lead Connector


A405887C01
1.521,0.125 1.885,0.396 0.365,0.271 0.073,0.104 0.385,0.302 0.313,0.198 10 false *a 1.677,0.198 1.833,0.396 0.156,0.198 10 false E
*a Signal Check Harness No. 2 Lead Connector


Disconnect the tank heater (urea pump) connector.


b.

Connect the signal check harness No. 2 to the DCU (emission control ECU assembly) vehicle side harness. (Do not connect the harness to the DCU (emission control ECU assembly).)


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
E-2 (HTT) - Body ground Ignition switch off 10 kΩ or higher
E-21 (EHTT) - Body ground Ignition switch off 10 kΩ or higher
E-2 (HTT) - E-36 (ELU) Ignition switch off 10 kΩ or higher
E-2 (HTT) - E-37 (ISG) Ignition switch off 10 kΩ or higher
E-2 (HTT) - E-43 (ETHU) Ignition switch off 10 kΩ or higher
E-2 (HTT) - E-44 (EPU) Ignition switch off 10 kΩ or higher
E-2 (HTT) - E-45 (MSG) Ignition switch off 10 kΩ or higher
E-2 (HTT) - E-60 (SGN4) Ignition switch off 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

2.INSPECT TANK HEATER (UREA PUMP)

NG

9.REPAIR OR REPLACE HARNESS OR CONNECTOR
2.INSPECT TANK HEATER (UREA PUMP)
a.
A355506C09
0.479,1.615 0.896,1.198 false 1.906,1.625 1.458,1.188 false 0.135,0.135 0.448,0.333 0.313,0.198 10 false *a 0.24,1.635 0.615,1.802 0.375,0.167 10 false HTT 1.927,1.625 2.302,1.792 0.375,0.167 10 false EHTT
*a Component without harness connected
(Tank Heater (Urea Pump))


Disconnect the tank heater (urea pump) connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
9 (HTT) - 11 (EHTT) 25°C 1.36 to 1.52 Ω



Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (TANK HEATER (UREA PUMP) - DCU (EMISSION CONTROL ECU ASSEMBLY))

NG

8.REPLACE TANK HEATER (UREA PUMP)
3.CHECK HARNESS AND CONNECTOR (TANK HEATER (UREA PUMP) - DCU (EMISSION CONTROL ECU ASSEMBLY))
a.
A405886C01
1.51,0.125 1.885,0.406 0.375,0.281 0.083,0.115 0.396,0.313 0.313,0.198 10 false *a 1.667,0.208 1.979,0.406 0.313,0.198 10 false E
*a Signal Check Harness No. 2 Lead Connector


Connect the tank heater (urea pump) connector.


b.

Connect the signal check harness No. 2 to the DCU (emission control ECU assembly) vehicle side harness. (Do not connect the harness to the DCU (emission control ECU assembly).)


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
E-2 (HTT) - E-21 (EHTT) 25°C 1.36 to 1.52 Ω



Result:
Proceed to
OK
NG



OK

4.CLEAR DTC

NG

7.REPAIR OR REPLACE HARNESS OR CONNECTOR
4.CLEAR DTC
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Clear the DTCs.

NOTICE:

Clear the DTCs with the engine stopped, as DTCs cannot be cleared while the engine is running.



e.

Turn the ignition switch off and wait for at least 30 seconds.


Result:
Proceed to
NEXT



NEXT

5.CHECK WHETHER DTC OUTPUT RECURS (DTC P20BD14)
5.CHECK WHETHER DTC OUTPUT RECURS (DTC P20BD14)
a.

Drive the vehicle in accordance with the driving pattern described in the Confirmation Driving Pattern.


b.

Connect the GTS to the DLC3.


c.

Turn the ignition switch to ON.


d.

Turn the GTS on.


e.

Enter the following menus: Powertrain / Urea Selective Catalytic Reduction / Trouble Codes.


f.

Read the DTCs.

Result:
Result Proceed to
DTC P20BD14 is output A
DTCs are not output B




A

6.REPLACE DCU (EMISSION CONTROL ECU ASSEMBLY)

B

END

6.REPLACE DCU (EMISSION CONTROL ECU ASSEMBLY)
a.

Replace the DCU (emission control ECU assembly).

Click hereEngine / Hybrid System>N04C-WA (EMISSION CONTROL)>UREA PUMP CONTROL ECU>REMOVAL


Result:
Proceed to
NEXT



NEXT

10.CLEAR DTC
7.REPAIR OR REPLACE HARNESS OR CONNECTOR
a.

Repair or replace the harness or connector.


Result:
Proceed to
NEXT



NEXT

10.CLEAR DTC
8.REPLACE TANK HEATER (UREA PUMP)
a.

Replace the tank heater (urea pump).

Click hereEngine / Hybrid System>N04C-WA (EMISSION CONTROL)>UREA PUMP>REMOVAL


Result:
Proceed to
NEXT



NEXT

10.CLEAR DTC
9.REPAIR OR REPLACE HARNESS OR CONNECTOR
a.

Repair or replace the harness or connector.


Result:
Proceed to
NEXT



NEXT

10.CLEAR DTC
10.CLEAR DTC
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Clear the DTCs.

NOTICE:

Clear the DTCs with the engine stopped, as DTCs cannot be cleared while the engine is running.



e.

Turn the ignition switch off and wait for at least 30 seconds.


Result:
Proceed to
NEXT



NEXT

11.CHECK WHETHER DTC OUTPUT RECURS (DTC P20BD14)
11.CHECK WHETHER DTC OUTPUT RECURS (DTC P20BD14)
a.

Drive the vehicle in accordance with the driving pattern described in the Confirmation Driving Pattern.


b.

Connect the GTS to the DLC3.


c.

Turn the ignition switch to ON.


d.

Turn the GTS on.


e.

Enter the following menus: Powertrain / Urea Selective Catalytic Reduction / Trouble Codes.


f.

Read the DTCs.

OK:

DTCs are not output



Result:
Proceed to
NEXT



NEXT

END