The No. 5 exhaust gas temperature sensor monitors the temperature at the SCR upstream.
The No. 5 exhaust gas temperature sensor detects disconnection and short-circuit based on the circuit voltage and signals in DCU (emission control ECU assembly).
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | MIL | Warning Indicate | Memory |
|---|---|---|---|---|---|---|
| P248215 | Exhaust Gas Temperature Sensor Circuit High Bank 1 Sensor 5 Circuit Short to Battery or Open | Diagnosis Condition:
·
Ignition switch ON. Malfunction Status: ·
The No. 5 exhaust gas temperature sensor voltage is higher than 4.9 V. Malfunction Duration: ·
3 seconds or more. |
·
Open or short in No. 5 exhaust gas temperature sensor circuit ·
No. 5 exhaust gas temperature sensor ·
DCU (emission control ECU assembly) |
Class A | AdBlue consumption warning light:
Comes on |
DTC stored |
Failure of No. 5 exhaust gas temperature sensor is detected.
After having restored to the normal conditions.
| DTC No. | DTC Detection Drive Pattern |
|---|---|
| P248215 | Idle the engine for 3 seconds after warming up the engine (the engine coolant temperature is 80°C (176°F) or higher). |
For the circuit diagram of the No. 5 exhaust gas temperature sensor refer to the DTC P007162.
Click hereEngine / Hybrid System>N04C-WA (EMISSION CONTROL)>UREA SELECTIVE CATALYTIC REDUCTION SYSTEM>P007162
For the circuit diagram of the DCU (emission control ECU assembly) power source refer to the DTC P0562A2.
Click hereEngine / Hybrid System>N04C-WA (EMISSION CONTROL)>UREA SELECTIVE CATALYTIC REDUCTION SYSTEM>P0562A2
For the circuit diagram of the VCPU terminal refer to the DTC P0642A2.
Click hereEngine / Hybrid System>N04C-WA (EMISSION CONTROL)>UREA SELECTIVE CATALYTIC REDUCTION SYSTEM>P0642A2
For the circuit diagram of the VCLU terminal refer to the DTC P0652A2.
Click hereEngine / Hybrid System>N04C-WA (EMISSION CONTROL)>UREA SELECTIVE CATALYTIC REDUCTION SYSTEM>P0652A2
Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.
Check the connector connection and contact pressure of the No. 5 exhaust gas temperature sensor connector.
The connector is connected securely and there are no contact pressure problems.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Check the installation condition (rattling and looseness) of the No. 5 exhaust gas temperature sensor.
Check that the sensing part of the No. 5 exhaust gas temperature sensor is free of dirt, blockage and damage.
The sensing part of the No. 5 exhaust gas temperature sensor is normal and the No. 5 exhaust gas temperature sensor is correctly installed.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Inspect the No. 5 exhaust gas temperature sensor.
Click hereEngine / Hybrid System>N04C-WA (EMISSION CONTROL)>EXHAUST GAS TEMPERATURE SENSOR>INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *a | Signal Check Harness No. 2 Lead Connector |
| *a | Signal Check Harness No. 2 Lead Connector |
Connect the signal check harness No. 2 to the DCU (emission control ECU assembly) vehicle side harness. (Do not connect the harness to the DCU (emission control ECU assembly).)
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| E-57 (EGT1) - Body ground | Ignition switch off | 10 kΩ or higher |
| E-60 (SGN4) - Body ground | Ignition switch off | 10 kΩ or higher |
| E-57 (EGT1) - E-17 (+BU1) | Ignition switch off | 10 kΩ or higher |
| E-57 (EGT1) -E-18 (+BU2) | Ignition switch off | 10 kΩ or higher |
| E-57 (EGT1) - E-19 (+BU3) | Ignition switch off | 10 kΩ or higher |
| E-57 (EGT1) - E-33 (+BU4) | Ignition switch off | 10 kΩ or higher |
| E-57 (EGT1) - E-51 (+BU5) | Ignition switch off | 10 kΩ or higher |
| E-57 (EGT1) - E-52 (PB3) | Ignition switch off | 10 kΩ or higher |
| E-57 (EGT1) - E-24 (VCLU) | Ignition switch off | 10 kΩ or higher |
| E-57 (EGT1) - E-25 (VCPU) | Ignition switch off | 10 kΩ or higher |
| E-57 (EGT1) - E-30 (BATT) | Ignition switch off | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *a | Signal Check Harness No. 2 Lead Connector |
Connect the No. 5 exhaust gas temperature sensor connector.
Connect the signal check harness No. 2 to the DCU (emission control ECU assembly) vehicle side harness. (Do not connect the harness to the DCU (emission control ECU assembly).)
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| E-57 (EGT1) - E-60 (SGN4) | 20°C | 13.7 to 29.8 kΩ |
| 50°C | 7.13 to 13.7 kΩ | |
| 80°C | 4.1 to 7.13 kΩ |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Clear the DTCs.
Clear the DTCs with the engine stopped, as DTCs cannot be cleared while the engine is running.
Turn the ignition switch off and wait for at least 30 seconds.
| Proceed to |
|---|
| NEXT |
NEXT
Drive the vehicle in accordance with the driving pattern described in the Confirmation Driving Pattern.
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Enter the following menus: Powertrain / Urea Selective Catalytic Reduction / Trouble Codes.
Read the DTCs.
| Result | Proceed to |
|---|---|
| DTC P248215 is output | A |
| DTCs are not output | B |
A
B
Replace the DCU (emission control ECU assembly).
Click hereEngine / Hybrid System>N04C-WA (EMISSION CONTROL)>UREA PUMP CONTROL ECU>REMOVAL
| Proceed to |
|---|
| NEXT |
NEXT
Repair or replace the harness or connector.
| Proceed to |
|---|
| NEXT |
NEXT
Repair or replace the harness or connector.
| Proceed to |
|---|
| NEXT |
NEXT
Replace the No. 5 exhaust gas temperature sensor.
Click hereEngine / Hybrid System>N04C-WA (EMISSION CONTROL)>EXHAUST GAS TEMPERATURE SENSOR>REMOVAL
| Proceed to |
|---|
| NEXT |
NEXT
Clean the sensing part of the No. 5 exhaust gas temperature sensor and correctly install it.
If the No. 5 exhaust gas temperature sensor is damaged, replace it.
| Proceed to |
|---|
| NEXT |
NEXT
Securely connect the No. 5 exhaust gas temperature sensor connector.
Repair parts as necessary.
| Proceed to |
|---|
| NEXT |
NEXT
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Clear the DTCs.
Clear the DTCs with the engine stopped, as DTCs cannot be cleared while the engine is running.
Turn the ignition switch off and wait for at least 30 seconds.
| Proceed to |
|---|
| NEXT |
NEXT
Drive the vehicle in accordance with the driving pattern described in the Confirmation Driving Pattern.
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Enter the following menus: Powertrain / Urea Selective Catalytic Reduction / Trouble Codes.
Read the DTCs.
DTCs are not output
| Proceed to |
|---|
| NEXT |
NEXT