Use the same procedure for RHD and LHD vehicles.
The procedure listed below is for RHD vehicles.
Use the same procedure for RH and LH sides.
The procedure listed below is for LH side.
1.REMOVE REAR SEAT ASSEMBLY (for Rear End)
for Tumble Type 4-Passenger Seat:
Click hereVehicle Interior>SEAT>REAR SEAT ASSEMBLY (for Tumble Type 4-Passenger Seat)>REMOVAL
for Fixed Type 4-Passenger Seat:
Click hereVehicle Interior>SEAT>REAR SEAT ASSEMBLY (for Fixed Type 4-Passenger Seat)>REMOVAL
45619K
2.REMOVE KNUCKLE STOPPER COVER (w/ Room Rack)
3.REMOVE ROOM RACK ASSEMBLY (w/ Room Rack)
63372A
4.REMOVE NO. 2 ROOF BOARD SET MOULDING (for Super Long Body)
63372F
5.REMOVE NO. 3 ROOF BOARD SET MOULDING
63324
6.REMOVE NO. 4 ROOF BOARD (for Long Body)
63324
7.REMOVE NO. 4 ROOF BOARD (for Super Long Body)
58614A
8.REMOVE NO. 4 MAT SET PLATE
66301D
9.REMOVE ROPE HOOK SUB-ASSEMBLY (w/ Rope Hook)
63349A
10.REMOVE REAR ROOF HEADLINING GARNISH
62487A
11.REMOVE INNER ROOF SIDE GARNISH COVER RH
62488A
12.REMOVE INNER ROOF SIDE GARNISH COVER LH
62471D
13.REMOVE REAR UPPER PILLAR GARNISH RH
62472D
14.REMOVE REAR UPPER PILLAR GARNISH LH
62228
15.REMOVE LOWER QUARTER PILLAR COVER LH
62512R
16.REMOVE REAR BODY REAR INSIDE TRIM LH
63316A
17.REMOVE NO. 6 ROOF HEADLINING
65937
18.REMOVE NO. 2 CURTAIN RAIL (for Long Body, w/ Curtain)
65937
19.REMOVE NO. 2 CURTAIN RAIL (for Super Long Body, w/ Curtain)
63940
20.REMOVE NO. 4 INNER COOLER DUCT LH (for Long Body)
63940
21.REMOVE NO. 4 INNER COOLER DUCT LH (for Super Long Body)
64814A
22.REMOVE BACK WINDOW CORNER GLASS LH
The back window corner glass LH may fall while performing this procedure. Therefore, use suction cups to hold the back window corner glass LH from the outside of the vehicle.
|
Protective Tape |
Apply protective tape to the outer surface of the vehicle body and glass to prevent scratches.
Install the suction cups to the back window corner glass LH.
From the interior, insert a piano wire between the vehicle body and glass.
| *1 | Piano Wire |
| *2 | Back Window Glass Clip LH |
Tie objects that can serve as handles (for example, wooden blocks) to both wire ends.
When separating the glass from the vehicle, Do not damage the vehicle paint or interior/exterior ornaments.
Cut through the adhesive by pulling the piano wire around the glass.
Using suction cups, disconnect the 2 clips and remove the back window corner glass LH.
Be careful not to drop the back window corner glass LH.
64813D
23.REMOVE BACK WINDOW GLASS ADHESIVE DAM
When reusing the back window corner glass LH:
| *a | Backside |
Using a scraper, remove the back window glass adhesive dam.
Do not damage the back window corner glass LH.
Be sure to replace the back window glass adhesive dam with a new one.
64828
24.REMOVE BACK WINDOW GLASS CLIP LH
When reusing the back window corner glass LH:
| *a | Backside |
Using a scraper, remove the 2 back window glass clips LH.
Do not damage the back window corner glass LH.
Be sure to replace the back window glass clip LH with a new one.
68294A
25.REMOVE BACK DOOR GLASS ADHESIVE DAM
When reusing the back window corner glass LH:
| *a | Backside |
Using a scraper, remove the 3 back door glass adhesive dams.
Do not damage the back window corner glass LH.
Be sure to replace the back door glass adhesive dam with a new one.