13613
1.INSTALL INJECTION PUMP DRIVE GEAR
Clamp the injection pump assembly in a vise.
Install the crankshaft angle sensor plate and the injection pump drive gear with the nut.
64 N*m (650 kgf*cm, 47 ft.*lbf)
Install a new O-ring onto the timer cover.
Install the timer cover onto the supply pump with the 2 bolts.
29 N*m (291 kgf*cm, 21 ft.*lbf)
22100
2.INSTALL SUPPLY PUMP ASSEMBLY
Install a new O-ring onto the timer cover.
Turn the drive gear and align the hole with the matchmark as shown in the illustration.
| *a | Matchmark |
| *b | Hole |
Check that the No. 1 cylinder is at TDC/compression.
| *a | Timing Mark |
Align the matchmarks of the timer cover and the front end plate, and then install the supply pump assembly with the 4 bolts.
29 N*m (291 kgf*cm, 21 ft.*lbf)
| *a | Matchmark |
When the crankshaft position sensor installation hole can be accessed directly:
Check that the knock pin of the injection pump drive gear is at the center of the hole.
When the crankshaft position sensor installation hole cannot be accessed directly:
Tape the screwdriver as shown in the illustration.
| *a | Vinyl Tape |
| *b | 36 mm (1.42 in.) |
| *c | 6 mm (0.236 in.) |
Remove the service plug and gasket from the timing chain cover sub-assembly.
| *1 | Service Plug |
Insert the taped screwdriver it into the timing gear case. Check that the tape and end of the timing gear case are aligned.
| *1 | Timing Chain Cover |
| *2 | Injection Pump Drive Gear |
| *a | Screwdriver |
| *b | 0 to 2 mm of the tape is visible |
| *c | 10 mm or more of the tape is visible |
Install the service plug and a new gasket to the timing chain cover sub-assembly.
8.0 N*m (82 kgf*cm, 71 ft.*lbf)
Install the injection pump stay with a nut and 2 bolts.
29 N*m (291 kgf*cm, 21 ft.*lbf)
Connect the 2 connectors.
23811
3.INSTALL FUEL FILTER TO INJECTION PUMP FUEL PIPE
Temporarily install the fuel filter to injection pump fuel pipe.
Using a 17 mm union nut wrench, install the fuel filter to injection pump fuel pipe with the 2 union nuts.
35 N*m (357 kgf*cm, 26 ft.*lbf)
Calculate the torque wrench reading when changing the fulcrum length of the torque wrench.
When using a union nut wrench (fulcrum length of 30 mm (1.18 in.)) + torque wrench (fulcrum length of 180 mm (7.09 in.)): 30 N*m (306 kgf*cm, 22 ft.*lbf)
| *a | Torque Wrench Fulcrum Length |
Install the fuel pipe clamp with the nut.
Tighten the nut until the clamp edge makes contact with the engine side clamp edge.
23802E
4.INSTALL FUEL PIPE SUB-ASSEMBLY
Install 8 gaskets and fuel pipe with the 5 union bolts.
25 N*m (255 kgf*cm, 18 ft.*lbf)
20 N*m (200 kgf*cm, 15 ft.*lbf)
42 N*m (428 kgf*cm, 31 ft.*lbf)
Connect the 2 fuel tubes.
Install the 4 fuel pipe clamps with the 4 nuts.
Tighten the nut until the clamp edge makes contact with the engine side clamp edge.
58396E
5.INSTALL WIRE HARNESS CLAMP BRACKET
Install the wire harness clamp bracket with 2 bolts.
29 N*m (291 kgf*cm, 21 ft.*lbf)
Connect the engine wire with nut.
8.4 N*m (86 kgf*cm, 74 ft.*lbf)
Install the 2 wire harness clamp brackets with 2 bolts.
32 N*m (327 kgf*cm, 24 ft.*lbf)
29 N*m (291 kgf*cm, 21 ft.*lbf)
Connect the ground wire with bolt.
8.4 N*m (86 kgf*cm, 74 ft.*lbf)
Connect the connector and 3 clamps.
11301K
6.INSTALL CRANKSHAFT POSITION SENSOR
17113D
7.INSTALL NO. 1 INTAKE PIPE
11202D
8.INSTALL NO. 2 CYLINDER HEAD COVER SUB-ASSEMBLY
25608
9.INSTALL EGR COOLER SUB-ASSEMBLY
10.CONNECT CABLE TO NEGATIVE BATTERY TERMINAL
11.BLEED AIR FROM FUEL SYSTEM
12.INSPECT FOR FUEL LEAK
13.INSPECT FOR COOLANT LEAK
14.INSPECT FOR OIL LEAK
15.SUPPLY PUMP INITIALIZATION