Home › Engine / Hybrid System › N04C-VJ (ENGINE CONTROL) › ECD SYSTEM › from 2021.01
RM2850E _51 Engine / Hybrid System _096807 N04C-VJ ENGINE CONTROL _0454116 ECD SYSTEM J

N04C-VJ ENGINE CONTROL  ECD SYSTEM  Engine Knocking or Rattling  


DESCRIPTION

Malfunction Condition Main Trouble Areas Related Trouble Areas
·

Knocking and abnormal sound due to extremely rich combustion

·

Abnormal sound due to friction between parts


1.

Injector assembly malfunctions

-

Injector assembly sliding malfunction

-

Injector assembly stuck closed

-

Injector assembly stuck open

-

Deposits in injector assembly

-

Injector assembly circuit malfunction


2.

Abnormal common rail pressure

-

Injection or supply pump assembly

-

Fuel pulsation sound

-

Air in fuel


3.

Friction between parts

4.

Compression pressure


·

Injector compensation codes

·

Fuel leak

·

Intake air system leak

·

Intake air system blockage

·

EGR system

·

Throttle valve system

·

Fuel pressure sensor (built into common rail assembly)

·

Manifold absolute pressure sensor

·

Atmosphere pressure sensor (built into ECM)

·

Vehicle modifications

·

Low quality fuel

·

Lack of fuel

·

ECM



HINT:
·

Specified values in the following troubleshooting flowchart are for reference only. Variations in the Data List values may occur depending on the measuring conditions or the vehicle's age. Do not judge the vehicle to be normal even when the Data List values indicate a standard level. There are possibly some concealed factors of the malfunction.

·

Check that the vehicle has not been modified in any way prior to the vehicle inspection.



CAUTION / NOTICE / HINT

NOTICE:
·

After replacing the ECM, the new ECM needs registration (Click hereEngine / Hybrid System>N04C-VJ (ENGINE CONTROL)>ECD SYSTEM>REGISTRATION) and initialization (Click here Engine / Hybrid System>N04C-VJ (ENGINE CONTROL)>ECD SYSTEM>INITIALIZATION).

·

After replacing the injection or supply pump assembly, the ECM needs initialization (Click here Engine / Hybrid System>N04C-VJ (ENGINE CONTROL)>ECD SYSTEM>INITIALIZATION).

·

After replacing the injector assembly, the ECM needs registration (Click here Engine / Hybrid System>N04C-VJ (ENGINE CONTROL)>ECD SYSTEM>REGISTRATION).



HINT:
·

This troubleshooting procedure checks for knocking and rattling.

·

Knocking is most likely to occur while the engine is idling.



PROCEDURE

1.CHECK SOUND AREA
a.

Find source of the abnormal sound using a mechanic's stethoscope.


Result:
Result Proceed to
Sound from injection or supply pump assembly A
Sound from parts other than injection or supply pump assembly B



A

2.CHECK HARNESS AND CONNECTOR IN ENGINE COMPARTMENT

B

REPAIR OR REPLACE MALFUNCTION PARTS

2.CHECK HARNESS AND CONNECTOR IN ENGINE COMPARTMENT
a.

Check the harness and connector connections.

OK:

Wire harnesses and connectors are connected securely.



Result:
Proceed to
OK
NG



OK

3.PERFORM CONFIRMATION DRIVING PATTERN

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.PERFORM CONFIRMATION DRIVING PATTERN
HINT:

Drive the vehicle according to the driving pattern below to allow the ECM to set DTCs relating to malfunctions of the fuel system, EGR system and throttle valve. If DTCs are set, problem areas can be identified.



b.

Fully warm up the engine.


c.

Allow the engine to idle for 5 minutes or more.


d.

Drive the vehicle at more than 40 km/h (25 mph) for 1 minute or more (Procedure "A").


e.

Decelerate and stop the vehicle (Procedure "B").


f.

Repeat steps "A" (See procedure "A") and "B" (See procedure "B") 4 times or more.


g.

Stop the engine and wait for at least 10 seconds (Procedure "C").


h.

Repeat steps "A" (See procedure "A") and "C" (See procedure "C") described above (to set DTCs relating to the EGR system and throttle valve).


i.

Drive the vehicle at more than 70 km/h (43 mph) for at least 1 minute (to set DTCs relating to the supply pump).


Result:
Proceed to
NEXT



NEXT

4.CHECK DTC OUTPUT (RELATING TO ENGINE)
4.CHECK DTC OUTPUT (RELATING TO ENGINE)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine and ECT / DTC.


e.

Read the DTCs.


Result:
Result Proceed to
No output A
Engine related DTCs B



A

5.PERFORM ACTIVE TEST USING GTS (TEST THE FUEL LEAK)

B

5.PERFORM ACTIVE TEST USING GTS (TEST THE FUEL LEAK)
HINT:

By performing this Active Test, the engine speed is maintained at 2000 rpm and the common rail internal fuel pressure is raised to the maximum operating pressure. As a result, a fuel leak check can be conducted while retaining the high common rail pressure.


a.

Connect the GTS to the DLC3.


b.

Start the engine.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine and ECT / Active Test / Test the Fuel Leak.


e.

Visually check the injection or supply pump assembly, injector assembly, and fuel line located between the injection or supply pump assembly and common rail assembly for fuel leaks and fuel pressure leaks. Also, perform the same check on the fuel line between the common rail assembly and the injector assembly.

HINT:

There may be fuel leaks inside the components, such as the injection or supply pump assembly.


OK:

No fuel leak.



Result:
Proceed to
OK
NG



OK

6.READ VALUE USING GTS (MAF AND FUEL PRESS)

NG

REPAIR OR REPLACE FUEL LEAK POINT

6.READ VALUE USING GTS (MAF AND FUEL PRESS)
a.

Connect the GTS to the DLC3.


b.

Start the engine, and warm it up.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine and ECT / Data List.


e.

Enter the following menus in order and read the values.

·

MAF

·

Fuel Press


Standard:
Item Engine Speed * Standard Range Description
MAF Idling 4 to 15 gm/s Intake air volume detected by mass air flow meter sub-assembly
3000 rpm (no engine load)Idling 80 to 90 gm/s
Fuel Pressure Idling 20000 to 30000 kPa Common rail assembly internal fuel pressure


Result:
Item Result Proceed to
MAF, and Fuel press Standard range A
Only MAF Outside standard range B
Only Fuel Press Outside standard range C


HINT:

*: The A/C switch and all accessory switches should be off, and the engine should be fully warmed up.




A

7.READ VALUE USING GTS (INJECTION FEED BACK VAL AND INJECTION VOLUME)

B

10.CHECK INTAKE SYSTEM

C

27.INSPECT COMMON RAIL ASSEMBLY (FUEL PRESSURE SENSOR)
7.READ VALUE USING GTS (INJECTION FEED BACK VAL AND INJECTION VOLUME)
a.

Enter the following menus in order and read the values.

·

Injection Feedback Val #1, #2, #3, and #4

·

Injection Volume


Standard:
Item Engine Speed* Standard Range Description
Injection Feedback Val #1 Idling -7.0 to 7.0 mm3/st Value of injector fuel injection volume compensates for differences in combustion condition of cylinders
·

Positive values indicate control which corrects combustion degradation

·

Negative values indicate control which corrects excessive combustion pressure

·

If problems exist, Injection Feedback Val may deviate from -7.0 and 7.0 mm3/st range


Injection Feedback Val #2 Idling -7.0 to 7.0 mm3/st
Injection Feedback Val #3 Idling -7.0 to 7.0 mm3/st
Injection Feedback Val #4 Idling -7.0 to 7.0 mm3/st
Injection Volume Idling 5.0 to 12.0 mm3/st Fuel injection volume value controlled by ECU
·

Controls NE signal, fuel temperature, engine coolant temperature, intake air temperature, atmospheric pressure, and EGR volume.

·

If problems exist, Injection Volume may be outside standard range




Result:
Result Proceed to
Standard range A
Injection Feedback Val #1 to #4 and/or Injection Volume outside standard range B


HINT:

*: The A/C switch and all accessory switches should be off, and the engine should be fully warmed up.




A

8.CHECK INJECTOR COMPENSATION CODE

B

20.IDENTIFY MALFUNCTIONING CYLINDER INJECTOR ASSEMBLY
8.CHECK INJECTOR COMPENSATION CODE
a.

Read the injector compensation code (Click here Engine / Hybrid System>N04C-VJ (ENGINE CONTROL)>ECD SYSTEM>PRECAUTION).

HINT:

If the injector compensation code is not correctly registered, it may cause malfunctions (Click here Engine / Hybrid System>N04C-VJ (ENGINE CONTROL)>ECD SYSTEM>REGISTRATION).



b.

Check the injector compensation code.

OK:

Compensation code of the installed injector assembly is same as the code registered in the ECM.



Result:
Proceed to
OK
NG



OK

9.RESET ECM

NG

PERFORM REGISTER INJECTOR COMPENSATION CODE

9.RESET ECM
a.

Disconnect the cable from the negative (-) battery terminal for at least 2 minutes.


b.

Reconnect the cable to the negative (-) battery terminal.


c.

Check whether the malfunction has been successfully repaired by performing a driving test.

OK:

Malfunction has been repaired successfully.



Result:
Proceed to
OK
NG



OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

10.CHECK INTAKE SYSTEM
10.CHECK INTAKE SYSTEM
a.

Check for air leaks and blockage between the air cleaner and turbocharger sub-assembly.


b.

Check for air leaks and blockage between the turbocharger sub-assembly and intake manifold.

OK:

No air leaks or blockage.



Result:
Proceed to
OK
NG



OK

11.INSPECT EXHAUST RETARDER ASSEMBLY

NG

REPAIR OR REPLACE MALFUNCTIONING PARTS

11.INSPECT EXHAUST RETARDER ASSEMBLY
a.

Inspect the exhaust retarder assembly.


Result:
Proceed to
OK
NG



OK

12.INSPECT EGR VALVE ASSEMBLY

NG

REPLACE EXHAUST RETARDER ASSEMBLY

12.INSPECT EGR VALVE ASSEMBLY

Result:
Proceed to
OK
NG



OK

13.INSPECT DIESEL THROTTLE BODY ASSEMBLY

NG

13.INSPECT DIESEL THROTTLE BODY ASSEMBLY
a.

Result:
Proceed to
OK
NG



OK

14.CHECK COMBUSTION SOUND

NG

14.CHECK COMBUSTION SOUND
a.

Confirm type of sound emitted.


Result:
Result Proceed to
Knocking A
Mechanical sound other than knocking B



A

15.PERFORM ACTIVE TEST USING GTS (CONTROL THE CYLINDER #1 TO #4 FUEL CUT)

B

25.BLEED AIR FROM FUEL SYSTEM
15.PERFORM ACTIVE TEST USING GTS (CONTROL THE CYLINDER #1 TO #4 FUEL CUT)
HINT:

Use this Active Test to determine the malfunctioning cylinder.


a.

Connect the GTS to the DLC3.


b.

Start the engine.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the Cylinder #1 to #4 Fuel Cut.

HINT:
·

If the engine idle speed does not change when a fuel injector is disabled, the cylinder being tested is malfunctioning.

·

If the cylinder being tested is normal, there will be a significant change in idle speed when the fuel injection is stopped for that cylinder.




Result:
Proceed to
NEXT



NEXT

16.CHECK CYLINDER COMPRESSION PRESSURE
16.CHECK CYLINDER COMPRESSION PRESSURE
a.

Check the cylinder compression pressure (Click here Engine / Hybrid System>N04C-VJ (ENGINE MECHANICAL)>ENGINE>ON-VEHICLE INSPECTION).


Result:
Proceed to
OK
NG



OK

17.CHECK MALFUNCTIONING CYLINDER INJECTION FOR DEPOSITS

NG

CHECK ENGINE TO DETERMINE CAUSE OF LOW COMPRESSION

17.CHECK MALFUNCTIONING CYLINDER INJECTION FOR DEPOSITS
HINT:

If an injector assembly is contaminated with deposits, the fuel injection volume deviates from the standard range. This may cause malfunctions.


a.

Check the injector assembly for any deposits.


Result:
Result Proceed to
Deposits A
No deposits B



A

18.CLEAN INJECTOR ASSEMBLY

B

REPLACE INJECTOR ASSEMBLY OF MALFUNCTIONING CYLINDER

18.CLEAN INJECTOR ASSEMBLY
a.

Wipe away deposits from the tips of the injector assemblies.

HINT:
·

Solvent or carbon removal agents help remove deposits easily.

·

Exercise extreme care not to damage the injector assemblies while wiping off the deposits.




Result:
Proceed to
NEXT



NEXT

19.READ VALUE USING GTS (INJECTION FEEDBACK VAL AND INJECTION VOLUME)
19.READ VALUE USING GTS (INJECTION FEEDBACK VAL AND INJECTION VOLUME)
a.

Reinstall the injector assembly to the cylinder head.


b.

Connect the GTS to the DLC3.


c.

Turn the ignition switch to ON.


d.

Turn the GTS on.


e.

Start the engine and warm it up.


f.

Enter the following menus: Powertrain / Engine and ECT / Data List.


g.

Enter the following menus in order and read the values.

·

Injection Feedback Val #1, #2, #3, and #4

·

Injection Volume


Standard:
Item Engine Speed* Reference Value
Injection Feedback Val #1 to #4 Idling -7.0 to 7.0 mm3/st
Injection Volume Idling 5.0 to 12.0 mm3/st


HINT:
·

*: The A/C switch and all accessory switches should be off, and the engine should be fully warmed up.

·

When the values are outside the standard range, deposits inside the injector assembly may be causing the problem.



OK:

Values are within the standard range.



Result:
Proceed to
OK
NG



OK

END

NG

REPLACE INJECTOR ASSEMBLY OF MALFUNCTIONING CYLINDER

20.IDENTIFY MALFUNCTIONING CYLINDER INJECTOR ASSEMBLY
a.

Follow the instructions in the table below according to the check result of the GTS.

HINT:

This operation is based on the premise that the common rail pressure is normal.


Standard:
Item Engine Speed*1 Reference Value
Injection Feedback Val #1 to #4 Idling -7.0 to 7.0 mm3/st
Injection Volume Idling 5.0 to 12.0 mm3/st


HINT:

*1: The A/C switch and all accessory switches should be off, and the engine should be fully warmed up.


Injection Volume Injection volume
Injection Feedback Val #1 to #4 Less than 5.0 mm3/st Between 5.0 and 19.0 mm3/st (Normal) More than 19.0 mm3/st
7.0 mm3/st or more, -7.0 mm3/st or less A B B
Between -7.0 and 7.0 mm3/st - Normal C*2


Result:
Proceed to Inspection Areas Descriptions
A Inspect and repair cylinder injector with revised injection volume of less than -7.0 mm3/st:
·

Perform power balance inspection and identify malfunctioning cylinder

·

Replace malfunctioning cylinder injector


Abnormal value cylinder injector injects excessively large quantity of fuel
B Identify malfunctioning cylinders by conducting power balance inspection:
·

Perform power balance inspection to identify malfunctioning cylinders

·

Clean malfunctioning cylinder injector, then check and repair it


Abnormal value cylinder injector injects excessively large quantity of fuel:
·

Fuel injection volume too low due to injector nozzle being blocked by deposits

·

Abnormal value cylinder injector compression decreases

·

Abnormal value cylinder injector injects excessively large quantity of fuel


C Inspect and repair all cylinder injectors:
Clean all cylinder injectors, and then inspect and repair them
All cylinder injectors inject excessively small quantity of fuel:
Fuel injection volume too low due to all cylinder injector nozzles being blocked by deposits


HINT:

*2: When the Injection Volume displayed on the GTS is large despite the Fuel Press and Injection Feedback Val #1 to #4 in the Data List being normal, the injector assembly may be clogged. In this case, there may be deposits inside or outside the injector assembly.

·

Despite the injector assembly functioning normally, the indicated Injection Feedback Val #1 to #4 value may be outside the normal operating range due to compensation for other problems (such as low compression).

·

Injection Feedback Val #1 to #4 is the value used to correct the fuel injection volumes of each cylinder, in order to optimize (compensate for the unevenness between) all the cylinder combustion conditions. If any of the cylinders malfunction, the fuel injection volumes for the normal cylinders are corrected simultaneously. As a result, the Injection Feedback Val #1 to #4 may deviate from the standard range.




A

21.PERFORM ACTIVE TEST USING GTS (CONTROL THE CYLINDER #1 TO #4 FUEL CUT)

B

15.PERFORM ACTIVE TEST USING GTS (CONTROL THE CYLINDER #1 TO #4 FUEL CUT)

C

22.CHECK ALL CYLINDER INJECTION ASSEMBLY FOR DEPOSITS
21.PERFORM ACTIVE TEST USING GTS (CONTROL THE CYLINDER #1 TO #4 FUEL CUT)
HINT:

Use this Active Test to determine the malfunctioning cylinder.


a.

Connect the GTS to the DLC3.


b.

Start the engine.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the Cylinder #1 to #4 Fuel Cut.

HINT:
·

If the engine idle speed does not change when a fuel injector assembly is disabled, the cylinder being tested is malfunctioning.

·

If the cylinder being tested is normal, there will be a significant change in idle speed when the fuel injection is stopped for that cylinder.




Result:
Proceed to
NEXT



NEXT

REPLACE INJECTOR ASSEMBLY OF MALFUNCTIONING CYLINDER

22.CHECK ALL CYLINDER INJECTION ASSEMBLY FOR DEPOSITS
HINT:

If an injector assembly is contaminated with deposits, the fuel injection volume deviates from the standard range. This may cause malfunctions.


a.

Check the injector assembly for any deposits.


Result:
Result Proceed to
Deposits A
No deposits B



A

23.CLEAN INJECTOR ASSEMBLY

B

REPLACE ALL CYLINDER INJECTOR ASSEMBLY

23.CLEAN INJECTOR ASSEMBLY
a.

Wipe away deposits from the tips of the injector assemblies.

HINT:
·

Solvent or carbon removal agents help remove deposits easily.

·

Exercise extreme care not to damage the injector assemblies while wiping off the deposits.




Result:
Proceed to
NEXT



NEXT

24.READ VALUE USING GTS (INJECTION FEEDBACK VAL AND INJECTION VOLUME)
24.READ VALUE USING GTS (INJECTION FEEDBACK VAL AND INJECTION VOLUME)
a.

Reinstall the injector assembly to the cylinder head.


b.

Connect the GTS to the DLC3.


c.

Turn the ignition switch to ON.


d.

Turn the GTS on.


e.

Start the engine and warm it up.


f.

Enter the following menus: Powertrain / Engine and ECT / Data List.


g.

Enter the following menus in order and read the values displayed on the GTS respectively.

·

Injection Feedback Val #1, #2, #3, and #4

·

Injection Volume


Standard:
Item Engine Speed* Reference Value
Injection Feedback Val #1 to #4 Idling -7.0 to 7.0 mm3/st
Injection Volume Idling 5.0 to 12.0 mm3/st


HINT:

*: The A/C switch and all accessory switches should be off, and the engine should be fully warmed up. When the values are outside the standard range, deposits inside the injector assembly may be causing the problem.


OK:

Values are within the standard range.



Result:
Proceed to
OK
NG



OK

END

NG

REPLACE ALL CYLINDER INJECTOR ASSEMBLY

25.BLEED AIR FROM FUEL SYSTEM
a.

To bleed air from the priming pump, pump the priming pump until it becomes hard and cannot be pumped any more.


Result:
Proceed to
NEXT



NEXT

26.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
26.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
a.

Check whether the malfunction been successfully repaired by performing a driving test.

OK:

Malfunction has been repaired successfully.



Result:
Proceed to
NEXT



NEXT

END

27.INSPECT COMMON RAIL ASSEMBLY (FUEL PRESSURE SENSOR)
a.

Inspect the common rail assembly (fuel pressure sensor).

Click hereEngine / Hybrid System>N04C-VJ (FUEL)>COMMON RAIL>INSPECTION


Result:
Proceed to
OK
NG



OK

28.INSPECT INJECTION OR SUPPLY PUMP ASSEMBLY

NG

REPLACE COMMON RAIL ASSEMBLY

28.INSPECT INJECTION OR SUPPLY PUMP ASSEMBLY
a.

Inspect the injection or supply pump assembly (suction control valve).

Click hereEngine / Hybrid System>N04C-VJ (FUEL)>FUEL SUPPLY PUMP>INSPECTION


Result:
Proceed to
OK
NG



OK

29.READ VALUE USING GTS (TARGET PUMP SCV CURRENT)

NG

REPLACE INJECTION OR SUPPLY PUMP ASSEMBLY

29.READ VALUE USING GTS (TARGET PUMP SCV CURRENT)
a.

Connect the GTS to the DLC3.


b.

Start the engine.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine and ECT / Data List / Target Pump SCV Current.


e.

Read the value.

Standard:
Engine Speed Result
Idling 1350 to 2200 mA



Result:
Proceed to
OK
NG



OK

REPAIR OR REPLACE COMMON RAIL ASSEMBLY (PRESSURE LIMITER)

NG

REPLACE INJECTION OR SUPPLY PUMP ASSEMBLY