Home › Power Source / Network › CAN COMMUNICATION › CAN COMMUNICATION SYSTEM › from 2021.01
RM2850E _57 Power Source / Network _073263 CAN COMMUNICATION _0356688 CAN COMMUNICATION SYSTEM U

CAN COMMUNICATION  CAN COMMUNICATION SYSTEM  TERMINALS OF ECU  


NOTICE:
·

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work (Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).

·

Turn the ignition switch off before measuring the resistances between CAN main wires and between CAN branch wires.

·

Turn the ignition switch off before inspecting CAN wires for a ground short.

·

Before measuring the resistance of the CAN bus, turn the ignition switch off and leave the vehicle for 1 minute or more without operating the key, switches or opening or closing the doors. After that, disconnect the cable from the negative (-) battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.

·

This section describes the standard values for all CAN related components.



HINT:
·

Operating the ignition switch, any other switches or a door triggers related ECU and sensor communication on the CAN. This communication will cause the resistance value to change.

·

Even after DTCs are cleared, if a DTC is stored again after driving the vehicle for a while, the malfunction may be occurring due to vibration of the vehicle. In such a case, wiggling the ECUs or wire harness while performing the inspection below may help determine the cause of the malfunction.



JUNCTION CONNECTOR


a.
C379587N03
1.469,0.146 1.885,0.396 0.417,0.25 0.885,0.563 1.052,0.563 1.052,0.563 1.615,1 true 2.458,0.552 2.292,0.552 2.292,0.552 1.875,0.969 true 1.094,1.875 1.26,1.875 1.26,1.875 1.635,1.302 true 2.354,1.823 2.188,1.823 2.188,1.823 1.823,1.302 true 0.813,0.813 0.979,0.813 0.979,0.813 1.427,1.052 true 2.615,0.75 2.448,0.75 2.448,0.75 2.052,1.021 true 0.833,1.458 1,1.458 1,1.458 1.438,1.229 true 2.573,1.594 2.406,1.594 2.406,1.594 2.073,1.24 true 0.125,0.083 0.438,0.281 0.313,0.198 10 false *a 1.531,0.198 2.083,0.406 0.552,0.208 10 false A121 0.333,0.49 0.896,0.719 0.563,0.229 10 false CANH*c 2.667,0.688 3.25,0.917 0.583,0.229 10 false CANL*b 0.51,1.792 1.073,2.021 0.563,0.229 10 false CANH*e 2.417,1.74 3,1.969 0.583,0.229 10 false CANL*e 0.271,0.729 0.833,0.958 0.563,0.229 10 false CANH*b 2.531,0.479 3.115,0.708 0.583,0.229 10 false CANL*c 0.292,1.375 0.854,1.604 0.563,0.229 10 false CANH*d 2.635,1.521 3.219,1.75 0.583,0.229 10 false CANL*d

NO. 2 CAN JUNCTION CONNECTOR (for N04C-WA)

Text in Illustration
*a Front view of wire harness connector
(to No. 2 CAN Junction Connector)
*b for No. 6 CAN Junction Connector
*c for No. 10 CAN Junction Connector
*d for Particulate Matter Sensor
*e for No. 1 Nitrogen Oxides Sensor

Terminal No. (Symbol) Wiring Color Connect to
A121-1 (CANH) B No. 6 CAN junction connector
A121-4 (CANL) W
A121-2 (CANH) B No. 10 CAN junction connector
A121-3 (CANL) W
A121-5 (CANH) B Particulate matter sensor
A121-8 (CANL) W
A121-6 (CANH) P No. 1 nitrogen oxides sensor
A121-7 (CANL) L


b.
C358902E01
1.479,0.073 1.885,0.344 0.406,0.271 1.573,0.958 1.354,0.49 1.354,0.49 1.208,0.49 true 1.344,0.948 1.042,0.708 1.042,0.708 0.917,0.708 true 1.365,1.26 1.073,1.625 1.073,1.625 0.938,1.625 true 1.656,1.281 1.396,1.927 1.396,1.927 1.24,1.927 true 1.771,1.271 1.99,1.917 1.99,1.917 2.188,1.917 true 2.042,1.281 2.354,1.573 2.354,1.573 2.521,1.573 true 2.042,0.938 2.229,0.688 2.229,0.688 2.385,0.688 true 1.844,0.938 2,0.469 2,0.469 2.146,0.469 true 0.146,0.094 0.458,0.292 0.313,0.198 10 false *a 1.552,0.115 1.865,0.313 0.313,0.198 10 false A91 0.646,0.417 1.323,0.615 0.677,0.198 10 false CANH*c 0.313,0.625 0.99,0.823 0.677,0.198 10 false CANH*b 0.354,1.552 1.031,1.75 0.677,0.198 10 false CANH*d 0.656,1.844 1.333,2.042 0.677,0.198 10 false CANH*e 2.271,1.844 3.188,2.042 0.917,0.198 10 false CANL*d 2.594,1.49 3.25,1.677 0.656,0.188 10 false CANL*e 2.479,0.625 3.135,0.813 0.656,0.188 10 false CANL*c 2.198,0.385 2.844,0.542 0.646,0.156 10 false CANL*b

NO. 3 CAN JUNCTION CONNECTOR (except 1HZ)

Text in Illustration
*a Front view of wire harness connector
(to No. 3 CAN Junction Connector)
*b
·

for No. 63 Junction Connector (for LHD)

·

for No. 67 Junction Connector (for RHD)


*c for Brake Actuator Assembly (Skid Control ECU)
*d for Airbag ECU Assembly (w/ Airbag System)
*e for No. 73 Junction Connector (w/o Airbag System)

Terminal No. (Symbol) Wiring Color Connect to

*1: for LHD

*2: for RHD

*3: w/ Airbag System

*4: w/o Airbag System

A91-1 (CANH) B
·

No. 63 junction connector*1

·

No. 67 junction connector*2


A91-3 (CANL) W
A91-2 (CANH) P Brake actuator assembly (skid control ECU)
A91-4 (CANL) V
A91-5 (CANH) B Airbag ECU assembly*3
A91-7 (CANL) W
A91-6 (CANH) B No. 73 junction connector*4
A91-8 (CANL) W


c.
C379587N08
1.469,0.146 1.885,0.396 0.417,0.25 0.885,0.563 1.052,0.563 1.052,0.563 1.615,1 true 2.458,0.552 2.292,0.552 2.292,0.552 1.875,0.969 true 1.052,1.667 1.219,1.667 1.219,1.667 1.427,1.292 true 2.198,1.927 2.031,1.927 2.031,1.927 1.823,1.323 true 0.813,0.813 0.979,0.813 0.979,0.813 1.427,1.052 true 2.615,0.75 2.448,0.75 2.448,0.75 2.052,1.021 true 1.188,1.938 1.354,1.938 1.354,1.938 1.615,1.292 true 2.438,1.729 2.271,1.729 2.271,1.729 2.042,1.323 true 0.125,0.083 0.438,0.281 0.313,0.198 10 false *a 1.531,0.188 2.083,0.396 0.552,0.208 10 false B118 0.333,0.49 0.896,0.719 0.563,0.229 10 false CANH*c 2.667,0.688 3.25,0.917 0.583,0.229 10 false CANL*c 0.49,1.583 1.052,1.813 0.563,0.229 10 false CANH*d 2.281,1.885 2.865,2.115 0.583,0.229 10 false CANL*d 0.271,0.729 0.833,0.958 0.563,0.229 10 false CANH*b 2.531,0.479 3.115,0.708 0.583,0.229 10 false CANL*b 0.667,1.865 1.229,2.094 0.563,0.229 10 false CANH*e 2.5,1.656 3.063,1.885 0.563,0.229 10 false CANL*e

NO. 5 CAN JUNCTION CONNECTOR (for N04C-WA)

Text in Illustration
*a Front view of wire harness connector
(to No. 5 CAN Junction Connector)
*b for EGR Valve Assembly
*c for Turbocharger Sub-assembly
*d for No. 8 CAN Junction Connector
*e for No. 6 CAN Junction Connector

Terminal No. (Symbol) Wiring Color Connect to
B118-1 (CANH) Y EGR valve assembly
B118-3 (CANL) V
B118-2 (CANH) P Turbocharger sub-assembly
B118-4 (CANL) L
B118-5 (CANH) B No. 8 CAN junction connector
B118-7 (CANL) W
B118-6 (CANH) B No. 6 CAN junction connector
B118-8 (CANL) W


d.
C379587N05
1.469,0.146 1.885,0.396 0.417,0.25 0.885,0.563 1.052,0.563 1.052,0.563 1.615,1 true 2.458,0.552 2.292,0.552 2.292,0.552 1.875,0.969 true 1.052,1.667 1.219,1.667 1.219,1.667 1.448,1.292 true 2.354,1.635 2.188,1.635 2.188,1.635 1.854,1.281 true 0.813,0.813 0.979,0.813 0.979,0.813 1.427,1.052 true 2.615,0.75 2.448,0.75 2.448,0.75 2.052,1.021 true 0.125,0.083 0.438,0.281 0.313,0.198 10 false *a 1.542,0.208 1.906,0.417 0.365,0.208 10 false A122 0.333,0.49 0.896,0.719 0.563,0.229 10 false CANH*c 2.667,0.688 3.25,0.917 0.583,0.229 10 false CANL*c 0.49,1.583 1.052,1.813 0.563,0.229 10 false CANH*d 2.406,1.563 2.99,1.792 0.583,0.229 10 false CANL*d 0.271,0.729 0.833,0.958 0.563,0.229 10 false CANH*b 2.531,0.479 3.115,0.708 0.583,0.229 10 false CANL*b

NO. 6 CAN JUNCTION CONNECTOR (for N04C-WA)

Text in Illustration
*a Front view of wire harness connector
(to No. 6 CAN Junction Connector)
*b for No. 2 CAN Junction Connector
*c for No. 5 CAN Junction Connector
*d for No. 2 Nitrogen Oxides Sensor

Terminal No. (Symbol) Wiring Color Connect to
A122-1 (CANH) B No. 2 CAN junction connector
A122-3 (CANL) W
A122-2 (CANH) B No. 5 CAN junction connector
A122-4 (CANL) W
A122-5 (CANH) Y No. 2 nitrogen oxides sensor
A122-7 (CANL) V


e.

NO. 7 CAN JUNCTION CONNECTOR (for N04C-WA)

C405889N01
3.25,0.167 3.667,0.417 0.417,0.25 2.823,0.417 2.99,0.417 2.99,0.417 3.438,1.417 true 2.667,0.583 2.833,0.583 2.833,0.583 3.26,1.406 true 2.5,0.75 2.667,0.75 2.667,0.75 3.01,1.385 true 2.333,0.917 2.5,0.917 2.5,0.917 2.865,1.385 true 2.167,1.083 2.333,1.083 2.333,1.083 2.708,1.406 true 2.833,2.5 3,2.5 3,2.5 3.448,1.698 true 2.667,2.333 2.833,2.333 2.833,2.333 3.313,1.667 true 2.5,2.167 2.667,2.167 2.667,2.167 3,1.667 true 2.333,2 2.5,2 2.5,2 2.833,1.698 true 2.167,1.833 2.333,1.833 2.333,1.833 2.677,1.677 true 4.063,1.417 4.531,1.042 4.531,1.042 4.698,1.042 true 4.063,1.688 4.531,2.115 4.531,2.115 4.698,2.115 true 3.729,1.688 4.083,2.406 4.083,2.406 4.25,2.406 true 3.604,1.688 3.917,2.563 3.917,2.563 4.083,2.563 true 3.75,1.406 4.188,0.552 4.188,0.552 4.354,0.552 true 3.604,1.427 4.094,0.385 4.094,0.385 4.26,0.385 true 3.885,1.448 4.396,0.781 4.396,0.781 4.563,0.781 true 3.875,1.677 4.24,2.25 4.24,2.25 4.406,2.25 true 4.167,1.458 4.75,1.219 4.75,1.219 4.917,1.219 true 4.177,1.635 4.646,1.927 4.646,1.927 4.813,1.927 true 3.323,0.229 4.24,0.427 0.917,0.198 10 false A123 0.115,0.115 1.031,0.313 0.917,0.198 10 false *a 1.583,1.031 2.5,1.229 0.917,0.198 10 false CANH*b 1.771,0.844 2.688,1.042 0.917,0.198 10 false CANH*c 1.938,0.667 2.854,0.865 0.917,0.198 10 false CANH*d 2.094,0.49 3.01,0.688 0.917,0.198 10 false CANH*e 2.26,0.323 3.177,0.521 0.917,0.198 10 false CANH*f 1.583,1.75 2.5,1.948 0.917,0.198 10 false CANL*b 1.792,1.927 2.708,2.125 0.917,0.198 10 false CANL*c 1.969,2.094 2.885,2.292 0.917,0.198 10 false CANL*d 2.156,2.271 3.073,2.469 0.917,0.198 10 false CANL*e 2.323,2.448 3.24,2.646 0.917,0.198 10 false CANL*f 4.313,0.344 5.229,0.542 0.917,0.198 10 false CANH*g 4.406,0.521 5.323,0.719 0.917,0.198 10 false CANH*h 4.635,0.719 5.552,0.917 0.917,0.198 10 false CANH*i 4.167,2.5 5.083,2.698 0.917,0.198 10 false CANL*g 4.302,2.344 5.219,2.542 0.917,0.198 10 false CANL*h 4.458,2.198 5.375,2.396 0.917,0.198 10 false CANL*i 4.75,0.979 5.667,1.177 0.917,0.198 10 false CANH*j 4.76,2.063 5.677,2.26 0.917,0.198 10 false CANL*j 4.958,1.177 5.875,1.375 0.917,0.198 10 false CANH*k 4.875,1.854 5.792,2.052 0.917,0.198 10 false CANL*k

Text in Illustration
*a Front view of wire harness connector
(to No. 7 CAN Junction Connector)
*b for Transmission Control ECU Assembly (for Automatic Transmission)
*c for Translate ECU Assembly *d for No. 6 CAN Junction Terminal
*e for Central Gateway ECU (Network Gateway ECU) *f for Translate ECU Assembly (for Automatic Transmission)
*g for Transmission Control ECU Assembly (for Automatic Transmission) *h for No. 9 CAN Junction Connector
*i for ECM *j for Translate ECU Assembly
*k for No. 5 CAN Junction Terminal - -

Terminal No. (Symbol) Wiring Color Connect to

*: for Automatic Transmission

A123-1 (CANH) R Transmission control ECU assembly*
A123-12 (CANL) G
A123-2 (CANH) R Translate ECU assembly
A123-13 (CANL) G
A123-3 (CANH) R No. 6 CAN junction terminal
A123-14 (CANL) G
A123-5 (CANH) B Central gateway ECU (network gateway ECU)
A123-16 (CANL) W
A123-6 (CANH) B Translate ECU assembly*
A123-17 (CANL) W
A123-7 (CANH) Y Transmission control ECU assembly*
A123-18 (CANL) V
A123-8 (CANH) B No. 9 CAN junction connector
A123-19 (CANL) W
A123-9 (CANH) B ECM
A123-20 (CANL) W
A123-10 (CANH) B Translate ECU assembly
A123-21 (CANL) W
A123-11 (CANH) R No. 5 CAN junction terminal
A123-22 (CANL) G


f.
C379589N03
0.115,1.563 0.594,1.823 0.479,0.26 2.25,1.708 2.292,0.854 2.292,0.854 2.125,0.854 true 2.229,2.021 2.302,2.604 2.302,2.604 2.135,2.604 true 2.427,1.698 2.583,0.688 2.583,0.688 2.417,0.688 true 2.594,1.719 2.896,0.49 2.896,0.49 2.729,0.49 true 2.427,2.042 2.573,2.802 2.573,2.802 2.406,2.802 true 2.604,2.042 2.792,2.99 2.792,2.99 2.625,2.99 true 0.219,1.625 0.833,1.823 0.615,0.198 10 false B149 1.885,2.74 2.521,3 0.635,0.26 10 false CANL*c 1.594,0.802 2.51,1 0.917,0.198 10 false CANH*b 1.615,2.542 2.531,2.74 0.917,0.198 10 false CANL*b 0.052,0.083 0.969,0.281 0.917,0.198 10 false *a 1.875,0.625 2.792,0.823 0.917,0.198 10 false CANH*c 2.177,0.417 3.094,0.615 0.917,0.198 10 false CANH*d 2.125,2.938 2.76,3.198 0.635,0.26 10 false CANL*d

NO. 8 CAN JUNCTION CONNECTOR (for N04C-WA)

Text in Illustration
*a Front view of wire harness connector
(to No. 8 CAN Junction Connector)
*b for ECM
*c for No. 5 CAN Junction Connector
*d for No. 7 CAN Junction Terminal

Terminal No. (Symbol) Wiring Color Connect to
B149-9 (CANH) Y ECM
B149-20 (CANL) V
B149-10 (CANH) B No. 5 CAN junction connector
B149-21 (CANL) W
B149-11 (CANH) P No. 7 CAN junction terminal
B149-22 (CANL) L


g.
C379587N06
1.521,0.156 1.927,0.385 0.406,0.229 0.885,0.563 1.052,0.563 1.052,0.563 1.427,1 true 2.458,0.552 2.292,0.552 2.292,0.552 1.875,0.969 true 1.052,1.667 1.219,1.667 1.219,1.667 1.427,1.323 true 2.354,1.635 2.188,1.635 2.188,1.635 1.875,1.281 true 1.031,0.354 1.198,0.354 1.198,0.354 1.635,1 true 2.677,0.76 2.51,0.76 2.51,0.76 2.042,1.042 true 0.125,0.083 0.438,0.281 0.313,0.198 10 false *a 1.594,0.198 2.156,0.406 0.563,0.208 10 false P16 0.333,0.49 0.896,0.719 0.563,0.229 10 false CANH*b 2.51,0.479 3.094,0.708 0.583,0.229 10 false CANL*b 0.49,1.583 1.052,1.813 0.563,0.229 10 false CANH*d 2.406,1.563 2.99,1.792 0.583,0.229 10 false CANL*d 0.51,0.281 1.073,0.51 0.563,0.229 10 false CANH*c 2.729,0.708 3.313,0.938 0.583,0.229 10 false CANL*c

NO. 9 CAN JUNCTION CONNECTOR (for N04C-WA)

Text in Illustration
*a Front view of wire harness connector
(to No. 9 CAN Junction Connector)
*b for Emission Control ECU Assembly
*c for No. 3 CAN Junction Terminal
*d for No. 7 CAN Junction Connector

Terminal No. (Symbol) Wiring Color Connect to
P16-1 (CANH) Y Emission control ECU assembly
P16-3 (CANL) V
P16-2 (CANH) B No. 3 CAN junction terminal
P16-4 (CANL) W
P16-5 (CANH) B No. 7 CAN junction connector
P16-7 (CANL) W


h.
C379587N07
1.469,0.146 1.885,0.396 0.417,0.25 0.885,0.563 1.052,0.563 1.052,0.563 1.615,1 true 2.458,0.552 2.292,0.552 2.292,0.552 1.875,0.969 true 1.052,1.667 1.219,1.667 1.219,1.667 1.427,1.292 true 2.188,1.958 2.021,1.958 2.021,1.958 1.802,1.323 true 0.813,0.813 0.979,0.813 0.979,0.813 1.427,1.052 true 2.615,0.75 2.448,0.75 2.448,0.75 2.052,1.021 true 1.146,1.927 1.313,1.927 1.313,1.927 1.615,1.281 true 2.49,1.76 2.323,1.76 2.323,1.76 2.042,1.26 true 0.125,0.083 0.438,0.281 0.313,0.198 10 false *a 1.583,0.208 2.135,0.417 0.552,0.208 10 false P17 0.333,0.49 0.896,0.719 0.563,0.229 10 false CANH*c 2.667,0.688 3.25,0.917 0.583,0.229 10 false CANL*c 0.49,1.583 1.052,1.813 0.563,0.229 10 false CANH*d 2.271,1.896 2.854,2.125 0.583,0.229 10 false CANL*d 0.271,0.729 0.833,0.958 0.563,0.229 10 false CANH*b 2.531,0.479 3.115,0.708 0.583,0.229 10 false CANL*b 0.573,1.854 1.135,2.083 0.563,0.229 10 false CANH*e 2.563,1.698 3.146,1.927 0.583,0.229 10 false CANL*e

NO. 10 CAN JUNCTION CONNECTOR (for N04C-WA)

Text in Illustration
*a Front view of wire harness connector
(to No. 10 CAN Junction Connector)
*b for Emission Control ECU Assembly
*c for No. 4 CAN Junction Terminal
*d for No. 2 CAN Junction Connector
*e for Urea Sensor Assembly

Terminal No. (Symbol) Wiring Color Connect to
P17-1 (CANH) L Emission control ECU assembly
P17-3 (CANL) P
P17-2 (CANH) Y No. 4 CAN junction terminal
P17-4 (CANL) V
P17-5 (CANH) B No. 2 CAN junction connector
P17-7 (CANL) W
P17-6 (CANH) P Urea sensor assembly
P17-8 (CANL) L


i.
C358902E04
1.479,0.073 1.938,0.323 0.458,0.25 1.573,0.958 1.354,0.49 1.354,0.49 1.208,0.49 true 1.344,0.948 1.042,0.708 1.042,0.708 0.917,0.708 true 1.365,1.26 1.073,1.625 1.073,1.625 0.938,1.625 true 1.656,1.281 1.396,1.927 1.396,1.927 1.24,1.927 true 1.771,1.271 1.99,1.917 1.99,1.917 2.188,1.917 true 2.042,1.281 2.354,1.573 2.354,1.573 2.521,1.573 true 2.042,0.938 2.229,0.688 2.229,0.688 2.385,0.688 true 1.844,0.938 2,0.469 2,0.469 2.146,0.469 true 0.146,0.094 0.458,0.292 0.313,0.198 10 false *a 1.552,0.104 1.906,0.323 0.354,0.219 10 false A120 0.646,0.417 1.323,0.615 0.677,0.198 10 false CANH*c 0.313,0.625 0.99,0.823 0.677,0.198 10 false CANH*b 0.354,1.552 1.031,1.75 0.677,0.198 10 false CANH*d 0.656,1.844 1.333,2.042 0.677,0.198 10 false CANH*e 2.271,1.844 3.188,2.042 0.917,0.198 10 false CANL*d 2.594,1.49 3.25,1.677 0.656,0.188 10 false CANL*e 2.479,0.625 3.135,0.813 0.656,0.188 10 false CANL*c 2.198,0.385 2.844,0.542 0.646,0.156 10 false CANL*b

NO. 11 CAN JUNCTION CONNECTOR (for 1HZ)

Text in Illustration
*a Front view of wire harness connector
(to No. 11 CAN Junction Connector)
*b
·

for No. 63 Junction Connector (for LHD)

·

for No. 67 Junction Connector (for RHD)


*c for Brake Actuator Assembly (Skid Control ECU)
*d for Airbag ECU Assembly (w/ Airbag System)
*e for No. 73 Junction Connector (w/o Airbag System)

Terminal No. (Symbol) Wiring Color Connect to

*1: for LHD

*2: for RHD

*3: w/ Airbag System

*4: w/o Airbag System

A127-1 (CANH) B
·

No. 63 junction connector*1

·

No. 67 junction connector*2


A127-3 (CANL) W
A127-2 (CANH) P Brake actuator assembly (skid control ECU)
A127-4 (CANL) V
A127-5 (CANH) B Airbag ECU assembly*3
A127-7 (CANL) W
A127-6 (CANH) B No. 73 junction connector*4
A127-8 (CANL) W


j.

NO. 63 JUNCTION CONNECTOR (for LHD)

i.
C358905E04
0.135,1 0.5,1.271 0.365,0.271 1,1.083 0.813,0.854 0.813,0.854 0.677,0.854 true 1.125,1.042 0.875,0.563 0.875,0.563 0.729,0.563 true 1.281,1.052 0.979,0.302 0.979,0.302 0.854,0.302 true 1.448,1.052 1.698,0.135 1.698,0.135 1.833,0.135 true 1.563,1.063 1.813,0.313 1.813,0.313 1.938,0.313 true 1.708,1.063 1.979,0.51 1.979,0.51 2.104,0.51 true 0.208,1.052 0.667,1.25 0.458,0.198 10 false J90 0.104,0.781 1.021,0.979 0.917,0.198 10 false CANH*b 0.167,0.49 1.083,0.688 0.917,0.198 10 false CANH*c 0.271,0.208 1.188,0.406 0.917,0.198 10 false CANH*d 1.896,0.052 2.813,0.25 0.917,0.198 10 false CANL*b 2.01,0.25 2.927,0.448 0.917,0.198 10 false CANL*c 2.177,0.427 3.094,0.625 0.917,0.198 10 false CANL*d 0.063,0.063 0.375,0.26 0.313,0.198 10 false *a

for BUS 4

Text in Illustration
*a Front view of wire harness connector
(to No. 63 Junction Connector)
*b for Central Gateway ECU (Network Gateway ECU)
*c for Spiral with Sensor Cable Sub-assembly (Steering Angle Sensor)
*d
·

for No. 3 CAN Junction Connector (except 1HZ)

·

for No. 11 CAN Junction Connector (for 1HZ)



Terminal No. (Symbol) Wiring Color Connect to

*1: except 1HZ

*2: for 1HZ

J90-1 (CANH) GR Central gateway ECU (network gateway ECU)
J90-4 (CANL) BE
J90-2 (CANH) R Spiral with sensor cable sub-assembly (steering angle sensor)
J90-5 (CANL) G
J90-3 (CANH) B
·

No. 3 CAN junction connector*1

·

No. 11 CAN junction connector*2


J90-6 (CANL) W


ii.
C358905N09
0.198,0.938 0.573,1.198 0.375,0.26 1.021,1.052 1.01,0.458 1.01,0.458 0.875,0.458 true 1.188,1.063 1.188,0.219 1.188,0.219 1.042,0.219 true 1.021,1.302 1.01,1.729 1.01,1.729 0.875,1.729 true 1.177,1.333 1.177,1.938 1.177,1.938 1.042,1.938 true 0.281,0.979 0.74,1.177 0.458,0.198 10 false J91 0.073,0.052 0.385,0.25 0.313,0.198 10 false *a 0.51,1.854 1.427,2.052 0.917,0.198 10 false CANL*c 0.323,1.667 1.24,1.865 0.917,0.198 10 false CANL*b 0.281,0.385 1.198,0.583 0.917,0.198 10 false CANH*b 0.5,0.146 1.417,0.344 0.917,0.198 10 false CANH*c

for BUS 5

Text in Illustration
*a Front view of wire harness connector
(to No. 63 Junction Connector)
*b for Central Gateway ECU (Network Gateway ECU)
*c for Combination Meter Assembly

Terminal No. (Symbol) Wiring Color Connect to
J91-1 (CANH) Y Central gateway ECU (network gateway ECU)
J91-12 (CANL) L
J91-2 (CANH) B Combination meter assembly
J91-13 (CANL) W



k.
C358905E24
1.5,0.146 1.865,0.396 0.365,0.25 1,1.073 0.813,0.5 0.813,0.5 0.656,0.5 true 1.281,1.063 1.281,0.188 1.281,0.188 1.125,0.188 true 1,1.323 0.875,1.604 0.875,1.604 0.719,1.604 true 1.302,1.333 1.167,1.99 1.167,1.99 1.01,1.99 true 1.156,1.042 1.031,0.375 1.031,0.375 0.875,0.375 true 1.156,1.333 0.938,1.771 0.938,1.771 0.771,1.771 true 0.104,0.094 0.417,0.292 0.313,0.198 10 false *a 1.563,0.188 2.021,0.385 0.458,0.198 10 false A85 0.552,0.094 1.469,0.292 0.917,0.198 10 false CANH*c 0.083,0.438 1,0.635 0.917,0.198 10 false CANH*b 0.167,1.5 1.083,1.698 0.917,0.198 10 false CANL*b 0.438,1.896 1.354,2.094 0.917,0.198 10 false CANL*c 0.323,0.271 0.958,0.458 0.635,0.188 10 false CANH*d 0.198,1.688 0.854,1.865 0.656,0.177 10 false CANL*d

NO. 66 JUNCTION CONNECTOR (except N04C-WA and 1HZ)

Text in Illustration
*a Front view of wire harness connector
(to No. 66 Junction Connector)
*b for ECM
*c for Central Gateway ECU (Network Gateway ECU)
*d for Transmission Control ECU Assembly (for N04C-VJ)

Terminal No. (Symbol) Wiring Color Connect to

*: for N04C-VJ

A85-1 (CANH) V ECM
A85-12 (CANL) W
A85-2 (CANH) G Transmission control ECU assembly*
A85-13 (CANL) R
A85-3 (CANH) B Central gateway ECU (network gateway ECU)
A85-14 (CANL) W


l.
C358905E06
0.208,0.917 0.563,1.229 0.354,0.313 1.854,1.063 2.125,0.49 2.125,0.49 2.313,0.49 true 1.698,1.073 2.052,0.219 2.052,0.219 2.25,0.219 false 1.573,1.073 1.302,0.333 1.302,0.333 1.125,0.333 true 1.573,1.323 1.448,1.875 1.448,1.875 1.292,1.875 true 1.729,1.323 1.875,1.896 1.875,1.896 2.042,1.896 true 1.854,1.323 1.969,1.667 1.969,1.667 2.125,1.667 true 0.135,0.094 0.448,0.292 0.313,0.198 10 false *a 0.271,0.979 0.729,1.177 0.458,0.198 10 false J81 0.531,0.271 1.448,0.469 0.917,0.198 10 false CANH*b 2.313,0.146 3.229,0.344 0.917,0.198 10 false CANH*c 2.396,0.417 3.313,0.615 0.917,0.198 10 false CANH*d 0.698,1.792 1.615,1.99 0.917,0.198 10 false CANL*b 2.198,1.594 3.115,1.792 0.917,0.198 10 false CANL*d 2.104,1.813 3.021,2.01 0.917,0.198 10 false CANL*c

NO. 67 JUNCTION CONNECTOR (for RHD)

Text in Illustration
*a Front view of wire harness connector
(to No. 67 Junction Connector)
*b for Central Gateway ECU (Network Gateway ECU)
*c for Spiral with Sensor Cable Sub-assembly (Steering Angle Sensor)
*d
·

for No. 3 CAN Junction Connector (except 1HZ)

·

for No. 11 CAN Junction Connector (for 1HZ)



Terminal No. (Symbol) Wiring Color Connect to

*1: except 1HZ

*2: for 1HZ

J81-5 (CANH) GR Central gateway ECU (network gateway ECU)
J81-16 (CANL) BE
J81-6 (CANH) R Spiral with sensor cable sub-assembly (steering angle sensor)
J81-17 (CANL) G
J81-7 (CANH) B
·

No. 3 CAN junction connector*1

·

No. 11 CAN junction connector*2


J81-18 (CANL) W


m.
C358905N10
0.229,1.052 0.573,1.354 0.344,0.302 1.031,1.063 0.854,0.417 0.854,0.417 0.688,0.417 true 1.167,1.073 1.281,0.427 1.281,0.427 1.427,0.427 true 1.177,1.302 1.458,1.823 1.458,1.823 1.604,1.823 true 1.021,1.302 0.854,1.823 0.854,1.823 0.667,1.823 true 0.292,1.115 0.75,1.313 0.458,0.198 10 false J76 0.073,0.073 0.385,0.271 0.313,0.198 10 false *a 0.156,0.333 0.792,0.552 0.635,0.219 10 false CANH*b 1.469,0.354 2.104,0.573 0.635,0.219 10 false CANH*c 1.646,1.76 2.281,1.979 0.635,0.219 10 false CANL*c 0.135,1.74 0.771,1.958 0.635,0.219 10 false CANL*b

NO. 68 JUNCTION CONNECTOR (for RHD)

Text in Illustration
*a Front view of wire harness connector
(to No. 68 Junction Connector)
*b for Central Gateway ECU (Network Gateway ECU)
*c for Combination Meter Assembly

Terminal No. (Symbol) Wiring Color Connect to
J76-1 (CANH) Y Central gateway ECU (network gateway ECU)
J76-12 (CANL) L
J76-2 (CANH) B Combination meter assembly
J76-13 (CANL) W


n.
C358905E23
0.208,0.969 0.573,1.229 0.365,0.26 1.021,1.052 0.969,0.49 0.969,0.49 0.833,0.49 true 1.313,1.073 1.333,0.146 1.333,0.146 1.198,0.146 true 1.042,1.281 0.969,1.76 0.969,1.76 0.833,1.76 true 1.302,1.281 1.271,2.031 1.271,2.031 1.135,2.031 true 0.135,0.115 0.448,0.313 0.313,0.198 10 false *a 0.26,1.01 0.573,1.208 0.313,0.198 10 false A96 0.24,1.667 0.823,1.854 0.583,0.188 10 false CANL*b 0.656,0.042 1.24,0.229 0.583,0.188 10 false CANL*c 0.25,0.406 0.833,0.594 0.583,0.188 10 false CANH*b 0.552,1.948 1.135,2.135 0.583,0.188 10 false CANH*c

NO. 73 JUNCTION CONNECTOR (w/o Airbag System)

Text in Illustration
*a Front view of wire harness connector
(to No. 73 Junction Connector)
*b
·

for No. 3 CAN Junction Connector (except 1HZ)

·

for No. 11 CAN Junction Connector (for 1HZ)


*c for No. 1 CAN Junction Terminal

Terminal No. (Symbol) Wiring Color Connect to
A96-1 (CANH) B
·

No. 3 CAN junction connector (except 1HZ)

·

No. 11 CAN junction connector (for 1HZ)


A96-12 (CANL) W
A96-3 (CANH) B No. 1 CAN junction terminal
A96-14 (CANL) W


o.
C300866E19
0.271,0.74 0.667,1.031 0.396,0.292 1.333,0.708 1.135,0.406 1.135,0.406 0.979,0.406 true 1.667,0.688 1.448,0.167 1.448,0.167 1.26,0.167 true 0.104,0.073 0.417,0.271 0.313,0.198 10 false *a 0.385,0.354 1.302,0.552 0.917,0.198 10 false CANH*b 0.688,0.094 1.604,0.292 0.917,0.198 10 false CANL*b 0.333,0.792 0.792,0.99 0.458,0.198 10 false A76

NO. 1 CAN JUNCTION TERMINAL (w/o Airbag System)

Text in Illustration
*a Rear view of wire harness connector
(to No. 1 CAN Junction Terminal)
*b for No. 73 Junction Connector

Terminal No. (Symbol) Wiring Color Connect to
A76-3 (CANH) B No. 73 junction connector
A76-2 (CANL) W


p.
C300866N05
0.271,0.74 0.74,1.01 0.469,0.271 1.333,0.708 1.135,0.406 1.135,0.406 0.979,0.406 true 1.667,0.688 1.448,0.167 1.448,0.167 1.26,0.167 true 0.104,0.073 0.417,0.271 0.313,0.198 10 false *a 0.385,0.354 1.302,0.552 0.917,0.198 10 false VOUT*b 0.719,0.094 1.635,0.292 0.917,0.198 10 false VGND*b 0.333,0.792 0.792,0.99 0.458,0.198 10 false A117

NO. 3 CAN JUNCTION TERMINAL (for N04C-WA)

Text in Illustration
*a Rear view of wire harness connector
(to No. 3 CAN Junction Terminal)
*b for No. 9 CAN Junction Connector

Terminal No. (Symbol) Wiring Color Connect to
A117-3 (VOUT) B No. 9 CAN junction connector
A117-2 (VGND) W


q.
C300866N01
0.271,0.74 0.74,1.01 0.469,0.271 1.333,0.708 1.135,0.406 1.135,0.406 0.979,0.406 true 1.667,0.688 1.448,0.167 1.448,0.167 1.26,0.167 true 0.104,0.073 0.417,0.271 0.313,0.198 10 false *a 0.385,0.354 1.302,0.552 0.917,0.198 10 false VOUT*b 0.688,0.094 1.604,0.292 0.917,0.198 10 false VGND*b 0.333,0.792 0.792,0.99 0.458,0.198 10 false A118

NO. 4 CAN JUNCTION TERMINAL (for N04C-WA)

Text in Illustration
*a Rear view of wire harness connector
(to No. 4 CAN Junction Terminal)
*b for No. 10 CAN Junction Connector

Terminal No. (Symbol) Wiring Color Connect to
A118-3 (VOUT) B No. 10 CAN junction connector
A118-2 (VGND) W


r.
C300866N02
0.271,0.74 0.74,1.01 0.469,0.271 1.333,0.708 1.135,0.406 1.135,0.406 0.979,0.406 true 1.667,0.688 1.448,0.167 1.448,0.167 1.26,0.167 true 0.104,0.073 0.417,0.271 0.313,0.198 10 false *a 0.385,0.354 1.302,0.552 0.917,0.198 10 false CANH*b 0.719,0.094 1.635,0.292 0.917,0.198 10 false CANL*b 0.333,0.792 0.792,0.99 0.458,0.198 10 false A119

NO. 5 CAN JUNCTION TERMINAL (for N04C-WA)

Text in Illustration
*a Rear view of wire harness connector
(to No. 5 CAN Junction Terminal)
*b for No. 7 CAN Junction Connector

Terminal No. (Symbol) Wiring Color Connect to
A119-3 (CANH) R No. 7 CAN junction connector
A119-2 (CANL) G


s.
C300866N03
0.271,0.74 0.74,1.01 0.469,0.271 1.333,0.708 1.135,0.406 1.135,0.406 0.979,0.406 true 1.667,0.688 1.448,0.167 1.448,0.167 1.26,0.167 true 0.104,0.073 0.417,0.271 0.313,0.198 10 false *a 0.385,0.354 1.302,0.552 0.917,0.198 10 false CANH*b 0.719,0.094 1.635,0.292 0.917,0.198 10 false CANL*b 0.333,0.792 0.792,0.99 0.458,0.198 10 false A126

NO. 6 CAN JUNCTION TERMINAL (for N04C-WA)

Text in Illustration
*a Rear view of wire harness connector
(to No. 6 CAN Junction Terminal)
*b for No. 7 CAN Junction Connector

Terminal No. (Symbol) Wiring Color Connect to
A126-3 (CANH) R No. 7 CAN junction connector
A126-2 (CANL) G


t.
C300866N04
0.271,0.74 0.74,1.01 0.469,0.271 1.333,0.708 1.135,0.406 1.135,0.406 0.979,0.406 true 1.667,0.688 1.448,0.167 1.448,0.167 1.26,0.167 true 0.104,0.073 0.417,0.271 0.313,0.198 10 false *a 0.385,0.354 1.302,0.552 0.917,0.198 10 false VOUT*b 0.719,0.094 1.635,0.292 0.917,0.198 10 false VGND*b 0.333,0.792 0.792,0.99 0.458,0.198 10 false B145

NO. 7 CAN JUNCTION TERMINAL (for N04C-WA)

Text in Illustration
*a Rear view of wire harness connector
(to No. 7 CAN Junction Terminal)
*b for No. 8 CAN Junction Connector

Terminal No. (Symbol) Wiring Color Connect to
B145-3 (VOUT) P No. 8 CAN junction connector
B145-2 (VGND) L



CHECK DLC3


a.
C253362E42
1.479,0.115 1.854,0.406 0.375,0.292 1.583,0.917 1.365,0.417 1.365,0.417 1.198,0.417 false 1.948,0.896 2.073,0.438 2.073,0.438 2.25,0.438 false 1.948,1.479 1.875,1.875 1.875,1.875 1.719,1.875 false 2.313,1.469 2.438,1.885 2.438,1.885 2.635,1.885 false 0.115,0.094 0.427,0.292 0.313,0.198 10 false *a 1.552,0.156 2.01,0.354 0.458,0.198 10 false J45 0.917,0.333 1.229,0.531 0.313,0.198 10 false CG 2.333,0.365 2.823,0.583 0.49,0.219 10 false CANH 1.313,1.802 1.813,2.01 0.5,0.208 10 false CANL 2.74,1.802 3.146,2 0.406,0.198 10 false BAT

Disconnect the cable from the negative (-) battery terminal before measuring the resistances of the CAN main wire and CAN branch wire.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the airbag system.


NOTICE:

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION.)


Text in Illustration
*a Front view of DLC3


b.

Measure the resistance according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
J45-6 (CANH) - J45-14 (CANL) P - V HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) battery terminal 54 to 69 Ω
J45-6 (CANH) - J45-4 (CG) P - W-B HIGH-level CAN bus line - Ground Cable disconnected from negative (-) battery terminal 200 Ω or higher
J45-14 (CANL) - J45-4 (CG) V - W-B LOW-level CAN bus line - Ground Cable disconnected from negative (-) battery terminal 200 Ω or higher
J45-6 (CANH) - J45-16 (BAT) P - R HIGH-level CAN bus line - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
J45-14 (CANL) - J45-16 (BAT) V - R LOW-level CAN bus line - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher



CHECK CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU)


C331365N04
1.292,1.365 1.667,1.635 0.375,0.271 2.938,1.333 2.51,0.896 2.51,0.896 2.365,0.896 true 3.177,1.333 2.927,0.635 2.927,0.635 2.76,0.635 true 3.24,1.406 3.365,0.427 3.365,0.427 3.219,0.427 true 3.833,1.448 3.688,0.365 3.688,0.365 3.844,0.365 true 3.875,1.333 4.156,0.656 4.156,0.656 4.302,0.656 true 4.198,1.354 4.542,0.938 4.542,0.938 4.698,0.938 true 4.229,1.979 4.083,1.979 4.083,1.979 3.771,1.438 true 4.188,2.292 4.021,2.292 4.021,2.292 3.698,1.458 true 3.104,2.302 3.292,2.302 3.292,2.302 3.615,1.448 true 3.073,1.969 3.219,1.969 3.219,1.969 3.521,1.448 true 0.125,0.104 0.438,0.302 0.313,0.198 10 false *a 2.677,0.344 3.594,0.542 0.917,0.198 10 false CA2H*C 2.198,0.563 3.115,0.76 0.917,0.198 10 false CA2L*C 2.01,0.813 2.927,1.01 0.917,0.198 10 false GND 3.906,0.292 4.823,0.49 0.917,0.198 10 false CA6H*A 4.375,0.583 5.292,0.781 0.917,0.198 10 false CA6L*A 4.781,0.865 5.698,1.063 0.917,0.198 10 false BATT 4.302,1.906 5.219,2.104 0.917,0.198 10 false CA5H*D 4.281,2.219 5.198,2.417 0.917,0.198 10 false CA5L*D 2.542,2.219 3.458,2.417 0.917,0.198 10 false CA4L*B 2.51,1.896 3.427,2.094 0.917,0.198 10 false CA4H*B 1.375,1.406 1.833,1.604 0.458,0.198 10 false J51

Text in Illustration
*A V Bus *B Bus 2
*C Bus 4 *D Bus 5
*a Component without harness connected
(Central Gateway ECU [Network Gateway ECU])
- -

a.
C326490E89
1.458,0.146 1.802,0.385 0.344,0.24 0.396,1.76 0.219,1.76 0.219,1.76 0.448,0.979 true 1,1.99 1.146,1.99 1.146,1.99 1.375,1.208 true 1.417,2.063 1.281,2.063 1.281,2.063 1.51,1.208 true 1.958,1.896 1.792,1.896 1.792,1.896 1.656,1.219 true 2.448,1.771 2.302,1.771 2.302,1.771 1.802,1.208 true 0.729,0.406 0.854,0.406 0.854,0.406 1.115,0.938 true 0.938,0.177 1.083,0.177 1.083,0.177 1.26,1.135 true 2.167,0.115 1.99,0.115 1.99,0.115 2.292,1.125 true 2.427,0.281 2.271,0.281 2.271,0.281 2.438,0.938 true 2.896,0.448 2.771,0.448 2.771,0.448 2.927,0.917 true 0.063,0.042 0.375,0.24 0.313,0.198 10 false *a 0.396,0.104 1.313,0.302 0.917,0.198 10 false CA6H*A 0.177,0.323 1.094,0.521 0.917,0.198 10 false CA6L*A 0.458,1.677 1.375,1.875 0.917,0.198 10 false BATT 0.427,1.906 1.344,2.104 0.917,0.198 10 false CA5H*D 1.458,1.979 2.375,2.177 0.917,0.198 10 false CA5L*D 2.021,1.813 2.938,2.01 0.917,0.198 10 false CA4L*B 2.51,1.688 3.427,1.885 0.917,0.198 10 false CA4H*B 2.208,0.042 3.125,0.24 0.917,0.198 10 false CA2H*C 2.479,0.208 3.146,0.396 0.667,0.188 10 false CA2L*C 2.938,0.375 3.365,0.573 0.427,0.198 10 false GND 1.531,0.177 1.99,0.375 0.458,0.198 10 false J51

Disconnect the central gateway ECU (network gateway ECU) connector.

Text in Illustration
*A V Bus
*B Bus 2
*C Bus 4
*D Bus 5
*a Front view of wire harness connector
(to Central Gateway ECU [Network Gateway ECU])


b.

Measure the resistance according to the value(s) in the table below.

V Bus Branch Lines (DLC3 - Central gateway ECU [network gateway ECU])
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
J51-14 (CA6H) - J51-5 (CA6L) P - V HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) battery terminal 1 MΩ or higher
J51-14 (CA6H) - J51-10 (GND) P - W-B HIGH-level CAN bus line - Ground Cable disconnected from negative (-) battery terminal 200 Ω or higher
J51-5 (CA6L) - J51-10 (GND) V - W-B LOW-level CAN bus line - Ground Cable disconnected from negative (-) battery terminal 200 Ω or higher
J51-14 (CA6H) - J51-1 (BATT) P - L HIGH-level CAN bus line - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
J51-5 (CA6L) - J51-1 (BATT) V - L LOW-level CAN bus line - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher

Bus 2 Main Lines
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
J51-18 (CA4H) - J51-17 (CA4L) B - W HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) battery terminal 108 to 132 Ω
J51-18 (CA4H) - J51-10 (GND) B - W-B HIGH-level CAN bus line - Ground Cable disconnected from negative (-) battery terminal 200 Ω or higher
J51-17 (CA4L) - J51-10 (GND) W - W-B LOW-level CAN bus line - Ground Cable disconnected from negative (-) battery terminal 200 Ω or higher
J51-18 (CA4H) - J51-1 (BATT) B - L HIGH-level CAN bus line - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
J51-17 (CA4L) - J51-1 (BATT) W - L LOW-level CAN bus line - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher

Bus 4 Main Lines
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
J51-22 (CA2H) - J51-7 (CA2L) GR - BE HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) battery terminal 108 to 132 Ω
J51-22 (CA2H) - J51-10 (GND) GR - W-B HIGH-level CAN bus line - Ground Cable disconnected from negative (-) battery terminal 200 Ω or higher
J51-7 (CA2L) - J51-10 (GND) BE - W-B LOW-level CAN bus line - Ground Cable disconnected from negative (-) battery terminal 200 Ω or higher
J51-22 (CA2H) - J51-1 (BATT) GR - L HIGH-level CAN bus line - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
J51-7 (CA2L) - J51-1 (BATT) BE - L LOW-level CAN bus line - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher

Bus 5 Main Lines
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
J51-15 (CA5H) - J51-16 (CA5L) Y - L HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) battery terminal 108 to 132 Ω
J51-15 (CA5H) - J51-10 (GND) Y - W-B HIGH-level CAN bus line - Ground Cable disconnected from negative (-) battery terminal 200 Ω or higher
J51-16 (CA5L) - J51-10 (GND) L - W-B LOW-level CAN bus line - Ground Cable disconnected from negative (-) battery terminal 200 Ω or higher
J51-15 (CA5H) - J51-1 (BATT) Y - L HIGH-level CAN bus line - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
J51-16 (CA5L) - J51-1 (BATT) L - L LOW-level CAN bus line - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher



CHECK TRANSLATE ECU ASSEMBLY (for N04C-WA)


C407763N01
3.979,0.344 4.458,0.604 0.479,0.26 4.542,1.458 4.76,0.521 4.76,0.521 4.938,0.521 true 4.365,1.552 4.594,2.469 4.594,2.469 4.771,2.469 true 3.958,1.563 3.792,2.281 3.792,2.281 3.625,2.281 true 4.521,1.552 4.698,2.281 4.698,2.281 4.875,2.281 true 4.385,1.448 4.667,0.313 4.667,0.313 4.844,0.313 true 4.052,1.521 3.885,2.448 3.885,2.448 3.719,2.448 true 4.146,0.396 4.479,0.583 0.333,0.188 10 false V9 4.99,0.458 5.719,0.698 0.729,0.24 10 false CANP*B 3.177,2.375 3.792,2.583 0.615,0.208 10 false CAN+*A 3.104,2.219 3.719,2.427 0.615,0.208 10 false CAN-*A 4.927,2.219 5.656,2.458 0.729,0.24 10 false CANN*B 4.896,0.25 5.625,0.49 0.729,0.24 10 false CANP*C 4.823,2.406 5.552,2.646 0.729,0.24 10 false CANN*C 0.094,0.073 0.427,0.26 0.333,0.188 10 false *a

Text in Illustration
*A Bus 2 *B Transmission Local Bus
*C Engine Local Bus - -
*a Component without harness connected
(Translate ECU Assembly)
- -

a.

Disconnect the translate ECU assembly connector.

C422457N01
0.906,0.125 1.302,0.354 0.396,0.229 3.333,0.375 3.729,0.604 0.396,0.229 5.854,0.396 6.25,0.625 0.396,0.229 0.75,2.573 0.583,2.573 0.583,2.573 0.51,1.781 true 0.74,0.448 0.573,0.448 0.573,0.448 0.49,1.573 true 1.042,0.625 0.875,0.625 0.875,0.625 0.75,1.552 true 1,2.417 0.833,2.417 0.833,2.417 0.76,1.74 true 1.49,2.25 1.323,2.25 1.323,2.25 1.25,1.75 true 1.833,2.083 1.667,2.083 1.667,2.083 1.365,1.729 true 4.156,0.385 3.99,0.385 3.99,0.385 3.667,1.156 true 6.583,0.51 6.417,0.51 6.417,0.51 6.333,1.156 true 0.083,0.073 0.396,0.271 0.313,0.198 10 false *a 1.01,0.156 1.323,0.354 0.313,0.198 10 false V9 3.417,0.406 3.729,0.604 0.313,0.198 10 false V10 5.938,0.427 6.25,0.625 0.313,0.198 10 false V11 0.813,2.5 1.438,2.698 0.625,0.198 10 false CANN*B 0.802,0.375 1.427,0.573 0.625,0.198 10 false CANP*B 1.083,0.542 1.708,0.74 0.625,0.198 10 false CANP*C 1.042,2.344 1.667,2.542 0.625,0.198 10 false CANN*C 1.531,2.167 2.156,2.365 0.625,0.198 10 false CAN+*A 1.875,2.021 2.5,2.219 0.625,0.198 10 false CAN-*A 4.208,0.302 4.833,0.5 0.625,0.198 10 false GND 6.635,0.438 7.042,0.656 0.406,0.219 10 false AM1

Text in Illustration
*A Bus 2 *B Transmission Local Bus
*C Engine Local Bus - -
*a Front view of wire harness connector
(to Translate ECU Assembly)
- -


b.

Measure the resistance according to the value(s) in the table below.

Bus 2 Main Lines
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
V9-31 (CAN+) - V9-32 (CAN-) B - W HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) battery terminal 108 to 132 Ω
V9-31 (CAN+) - V10-4 (GND) B - W-B HIGH-level CAN bus line - Ground Cable disconnected from negative (-) battery terminal 200 Ω or higher
V9-32 (CAN-) - V10-4 (GND) W - W-B LOW-level CAN bus line - Ground Cable disconnected from negative (-) battery terminal 200 Ω or higher
V9-31 (CAN+) - V11-6 (AM1) B - GR HIGH-level CAN bus line - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
V9-32 (CAN-) - V11-6 (AM1) W - GR LOW-level CAN bus line - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher

Transmission Local Bus Branch Lines
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
V9-17 (CANP) - V9-28 (CANN) R - G HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) battery terminal 54 to 69 Ω
V9-17 (CANP) - V10-4 (GND) R - W-B HIGH-level CAN bus line - Ground Cable disconnected from negative (-) battery terminal 200 Ω or higher
V9-28 (CANN) - V10-4 (GND) G - W-B LOW-level CAN bus line - Ground Cable disconnected from negative (-) battery terminal 200 Ω or higher
V9-17 (CANP) - V11-6 (AM1) R - GR HIGH-level CAN bus line - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
V9-28 (CANN) - V11-6 (AM1) G - GR LOW-level CAN bus line - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher

Engine Local Bus Branch Lines
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
V9-19 (CANP) - V9-30 (CANN) B - W HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) battery terminal 54 to 69 Ω
V9-19 (CANP) - V10-4 (GND) B - W-B HIGH-level CAN bus line - Ground Cable disconnected from negative (-) battery terminal 200 Ω or higher
V9-30 (CANN) - V10-4 (GND) W - W-B LOW-level CAN bus line - Ground Cable disconnected from negative (-) battery terminal 200 Ω or higher
V9-19 (CANP) - V11-6 (AM1) B - GR HIGH-level CAN bus line - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
V9-30 (CANN) - V11-6 (AM1) W - GR LOW-level CAN bus line - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher



CHECK ECM (for 2TR-FE)


Refer to Terminals of ECU (Click hereEngine / Hybrid System>2TR-FE (ENGINE CONTROL)>SFI SYSTEM>TERMINALS OF ECM).

a.
C371312E01
1.458,0.167 1.885,0.458 0.427,0.292 1.406,2.344 1.833,2.635 0.427,0.292 1.479,0.938 0.885,0.323 0.885,0.323 0.698,0.323 true 1.635,1.427 1.448,2.031 1.448,2.031 1.271,2.031 true 2.125,3.792 2.125,4.406 2.125,4.406 1.979,4.406 true 2.271,3.792 2.271,4.406 2.271,4.406 2.469,4.406 true 1.01,1.958 1.625,2.156 0.615,0.198 10 false EC 0.323,0.26 0.938,0.458 0.615,0.198 10 false BATT 0.094,0.063 0.708,0.26 0.615,0.198 10 false *a 1.552,4.333 2.167,4.531 0.615,0.198 10 false CANH 2.552,4.323 3.167,4.521 0.615,0.198 10 false CANL 1.49,2.406 2.104,2.604 0.615,0.198 10 false A53 1.552,0.219 2.167,0.417 0.615,0.198 10 false A55

Disconnect the ECM connectors.

Text in Illustration
*a Front view of wire harness connector
(to ECM)


b.

Measure the resistance according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
A53-33 (CANH) - A53-34 (CANL) V - W HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) battery terminal 108 to 132 Ω
A53-33 (CANH) - A55-22 (EC) V - W-B HIGH-level CAN bus line - Ground Cable disconnected from negative (-) battery terminal 200 Ω or higher
A53-34 (CANL) - A55-22 (EC) W - W-B LOW-level CAN bus line - Ground Cable disconnected from negative (-) battery terminal 200 Ω or higher
A53-33 (CANH) - A55-3 (BATT) V - GR HIGH-level CAN bus line - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
A53-34 (CANL) - A55-3 (BATT) W - GR LOW-level CAN bus line - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher



CHECK ECM (for N04C-VQ, N04C-VL, N04C-VJ)


Refer to Terminals of ECU.

for N04C-VQ: Click hereEngine / Hybrid System>N04C-VQ (ENGINE CONTROL)>ECD SYSTEM>TERMINALS OF ECM

for N04C-VL: Click hereEngine / Hybrid System>N04C-VL (ENGINE CONTROL)>ECD SYSTEM>TERMINALS OF ECM

for N04C-VJ: Click hereEngine / Hybrid System>N04C-VJ (ENGINE CONTROL)>ECD SYSTEM>TERMINALS OF ECM

a.

Disconnect the ECM connectors.

C371313E01
1.167,0.333 1.542,0.604 0.375,0.271 3.438,0.333 3.813,0.604 0.375,0.271 5.396,0.354 5.823,0.635 0.427,0.281 0.542,1.188 0.688,1.188 0.688,1.188 1.021,1.313 true 0.542,1.521 0.698,1.521 0.698,1.521 1.021,1.427 true 3.427,2.354 3.594,2.354 3.594,2.354 3.813,1.885 true 4.688,1.177 4.833,1.177 4.833,1.177 5.083,1.26 true 0.125,1.115 0.74,1.313 0.615,0.198 10 false CANL 0.104,1.438 0.719,1.635 0.615,0.198 10 false CANH 3.031,2.281 3.646,2.479 0.615,0.198 10 false BATT 4.448,1.104 5.063,1.302 0.615,0.198 10 false E1 1.229,0.396 1.688,0.594 0.458,0.198 10 false A56 3.51,0.385 3.969,0.583 0.458,0.198 10 false A57 5.458,0.417 5.917,0.615 0.458,0.198 10 false B102 0.125,0.104 0.438,0.302 0.313,0.198 10 false *a

Text in Illustration
*a Front view of wire harness connector
(to ECM)
- -


b.

Measure the resistance according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
A56-7 (CANH) - A56-1 (CANL) V - W HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) battery terminal 108 to 132 Ω
A56-7 (CANH) - B102-1 (E1) V - BR HIGH-level CAN bus line - Ground Cable disconnected from negative (-) battery terminal 200 Ω or higher
A56-1 (CANL) - B102-1 (E1) W - BR LOW-level CAN bus line - Ground Cable disconnected from negative (-) battery terminal 200 Ω or higher
A56-7 (CANH) - A57-23 (BATT) V - GR HIGH-level CAN bus line - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
A56-1 (CANL) - A57-23 (BATT) W - GR LOW-level CAN bus line - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher



CHECK ECM (for N04C-WA)


SST
09843-E7010  

Refer to Terminals of ECU (Click hereEngine / Hybrid System>N04C-WA (ENGINE CONTROL)>ECD SYSTEM>TERMINALS OF ECM)

a.

Connect the signal check harness to the ECM vehicle side harness.

C379569N01
2.115,0.063 2.469,0.281 0.354,0.219 4.583,0.063 4.938,0.281 0.354,0.219 4.896,1.115 5.667,1.417 5.667,1.417 5.833,1.417 true 4.854,0.719 5.406,0.167 5.406,0.167 5.656,0.167 true 3.021,0.719 2.74,0.167 2.74,0.167 2.99,0.167 true 3.052,1.073 3.229,1.396 3.229,1.396 3.479,1.396 true 3.813,0.583 3.708,0.146 3.708,0.146 3.958,0.146 true 5.635,1.073 5.865,0.917 5.865,0.917 6.031,0.917 true 0.104,0.073 0.417,0.271 0.313,0.198 10 false *a 5.896,1.344 6.5,1.573 0.604,0.229 10 false CANH*A 5.729,0.063 6.281,0.292 0.552,0.229 10 false CANL*A 3.052,0.094 3.656,0.323 0.604,0.229 10 false CAN+*B 3.531,1.354 4.135,1.583 0.604,0.229 10 false CAN-*B 2.281,0.104 2.885,0.333 0.604,0.229 10 false E 4.708,0.104 5.313,0.333 0.604,0.229 10 false V 4.021,0.063 4.625,0.292 0.604,0.229 10 false +B 6.094,0.854 6.698,1.083 0.604,0.229 10 false E01

Text in Illustration
*A Emission Control Local Bus *B Engine Local Bus
*a Signal Check Harness Connector - -

NOTICE:

Connect the signal check harness to prevent damage to the connector and improve work efficiency when performing the check.


HINT:

Refer to the following table for the ECU connector terminals and their corresponding signal check connector terminals.

ECU Connector Terminal Signal Check Harness Connector Terminal
A115-48 (CANH) V36 (CANH)
A115-59 (CANL) V16 (CANL)
A115-49 (+B) V1 (+B)
A115-12 (E01) V40 (E01)
B142-80 (CAN+) E59 (CAN+)
B142-102 (CAN-) E79 (CAN-)



b.

Measure the resistance according to the value(s) in the table below.

Emission Control Local Bus Branch Lines
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
V36 (CANH) - V16 (CANL) # - # HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) battery terminal 54 to 69 Ω
V36 (CANH) - V40 (E01) # - # HIGH-level CAN bus line - Ground Cable disconnected from negative (-) battery terminal 200 Ω or higher
V16 (CANL) - V40 (E01) # - # LOW-level CAN bus line - Ground Cable disconnected from negative (-) battery terminal 200 Ω or higher
V36 (CANH) - V1 (+B) # - # HIGH-level CAN bus line - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
V16 (CANL) - V1 (+B) # - # LOW-level CAN bus line - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher

Engine Local Bus Branch Lines
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
E59 (CAN+) - E79 (CAN-) # - # HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) battery terminal 54 to 69 Ω
E59 (CAN+) - V40 (E01) # - # HIGH-level CAN bus line - Ground Cable disconnected from negative (-) battery terminal 200 Ω or higher
E79 (CAN-) - V40 (E01) # - # LOW-level CAN bus line - Ground Cable disconnected from negative (-) battery terminal 200 Ω or higher
E59 (CAN+) - V1 (+B) # - # HIGH-level CAN bus line - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
E79 (CAN-) - V1 (+B) # - # LOW-level CAN bus line - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher



CHECK EMISSION CONTROL ECU ASSEMBLY (for N04C-WA)


SST
09843-E7020  

Refer to Terminals of ECU (Click hereEngine / Hybrid System>N04C-WA (EMISSION CONTROL)>UREA SELECTIVE CATALYTIC REDUCTION SYSTEM>TERMINALS OF ECM).

a.
C421149N01
1.542,0.375 1.927,0.594 0.385,0.219 0.667,0.542 0.833,0.542 0.833,0.542 0.625,1.302 true 2.635,0.167 2.469,0.167 2.469,0.167 2.813,1.146 true 2.073,0.177 2.24,0.177 2.24,0.177 2.604,1.104 true 1.51,0.688 1.677,0.688 1.677,0.688 2.313,1.135 true 1.365,2.281 1.531,2.281 1.531,2.281 2.333,1.792 true 2.458,2.354 2.625,2.354 2.625,2.354 2.896,1.615 true 1.688,0.417 1.844,0.615 0.156,0.198 10 false E 0.104,0.104 0.354,0.313 0.25,0.208 10 false *a 0.115,0.479 0.729,0.708 0.615,0.229 10 false CA2H*A 2.698,0.104 3.313,0.333 0.615,0.229 10 false CA2L*A 1.552,0.115 2.167,0.344 0.615,0.229 10 false CAN+*B 0.979,0.625 1.594,0.854 0.615,0.229 10 false CAN-*B 1.104,2.208 1.719,2.438 0.615,0.229 10 false E01 2.094,2.271 2.708,2.5 0.615,0.229 10 false BATT

Connect the signal check harness to the emission control ECU assembly vehicle side harness.

Text in Illustration
*A Emission Control Local Bus
*B Engine Local Bus
*a Signal Check Harness Connector

NOTICE:

Connect the signal check harness to prevent damage to the connector and improve work efficiency when performing the check.


HINT:

Refer to the following table for the ECU connector terminals and their corresponding signal check connector terminals.

ECU Connector Terminal Signal Check Harness Connector Terminal
P12-9 (CAN+) E9 (CAN+)
P12-8 (CAN-) E8 (CAN-)
P12-11 (CA2H) E11 (CA2H)
P12-10 (CA2L) E10 (CA2L)
P12-30 (BATT) E30 (BATT)
P12-38 (E01) E38 (E01)



b.

Measure the resistance according to the value(s) in the table below.

Emission Control Local Bus Branch Lines
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
E11 (CA2H) - E10 (CA2L) # - # HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) battery terminal 54 to 69 Ω
E11 (CA2H) - E38 (E01) # - # HIGH-level CAN bus line - Ground Cable disconnected from negative (-) battery terminal 200 Ω or higher
E10 (CA2L) - E38 (E01) # - # LOW-level CAN bus line - Ground Cable disconnected from negative (-) battery terminal 200 Ω or higher
E11 (CA2H) - E30 (BATT) # - # HIGH-level CAN bus line - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
E10 (CA2L) - E30 (BATT) # - # LOW-level CAN bus line - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher

Engine Local Bus Branch Lines
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
E9 (CAN+) - E8 (CAN-) # - # HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) battery terminal 54 to 69 Ω
E9 (CAN+) - E38 (E01) # - # HIGH-level CAN bus line - Ground Cable disconnected from negative (-) battery terminal 200 Ω or higher
E8 (CAN-) - E38 (E01) # - # LOW-level CAN bus line - Ground Cable disconnected from negative (-) battery terminal 200 Ω or higher
E9 (CAN+) - E30 (BATT) # - # HIGH-level CAN bus line - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
E8 (CAN-) - E30 (BATT) # - # LOW-level CAN bus line - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher



CHECK TRANSMISSION CONTROL ECU ASSEMBLY (for N04C-WA with Automatic Transmission, N04C-VJ)


Click hereDrivetrain>A861E (AUTOMATIC TRANSMISSION / TRANSAXLE)>AUTOMATIC TRANSMISSION SYSTEM>TERMINALS OF ECU

a.
C358903N04
1.438,0.365 1.854,0.646 0.417,0.281 1.385,2.792 1.542,2.792 1.542,2.792 1.542,2.115 true 2.417,2.667 2.26,2.667 2.26,2.667 1.75,1.865 true 0.865,2.531 1.021,2.531 1.021,2.531 1.542,1.823 true 2.365,2.917 2.208,2.917 2.208,2.917 1.698,2.115 true 2.594,0.99 2.438,0.99 2.438,0.99 2.344,1.479 true 0.677,1.833 0.833,1.833 0.833,1.833 1.073,2.01 true 0.063,0.083 0.375,0.281 0.313,0.198 10 false *a 1.5,0.427 1.958,0.625 0.458,0.198 10 false B133 0.854,2.729 1.469,2.927 0.615,0.198 10 false CANH*B 2.479,2.583 3.094,2.781 0.615,0.198 10 false CANL*A 0.313,2.49 0.927,2.688 0.615,0.198 10 false CANH*A 2.438,2.865 3.052,3.063 0.615,0.198 10 false CANL*B 2.635,0.906 3.25,1.104 0.615,0.198 10 false +B 0.333,1.75 0.948,1.948 0.615,0.198 10 false GND

Disconnect the transmission control ECU assembly connector.

Text in Illustration
*A Bus 2 (for N04C-VJ)
*B Transmission Local Bus (for N04C-WA)
*a Front view of wire harness connector
(to Transmission Control ECU Assembly)


b.

Measure the resistance according to the value(s) in the table below.

Bus 2 Branch Lines
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
B133-11 (CANH) - B133-12 (CANL) Y - V HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) battery terminal 54 to 69 Ω
B133-11 (CANH) - B133-17 (GND) Y - W-B HIGH-level CAN bus line - Ground Cable disconnected from negative (-) battery terminal 200 Ω or higher
B133-12 (CANL) - B133-17 (GND) V - W-B LOW-level CAN bus line - Ground Cable disconnected from negative (-) battery terminal 200 Ω or higher
B133-11 (CANH) - B133-7 (+B) Y - V HIGH-level CAN bus line - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
B133-12 (CANL) - B133-7 (+B) V - V LOW-level CAN bus line - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher

Transmission Local Bus Branch Lines
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
B133-20 (CAN+) - B133-21 (CAN-) R - G HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) battery terminal 54 to 69 Ω
B133-20 (CAN+) - B133-17 (GND) R - W-B HIGH-level CAN bus line - Ground Cable disconnected from negative (-) battery terminal 200 Ω or higher
B133-21 (CAN-) - B133-17 (GND) G - W-B LOW-level CAN bus line - Ground Cable disconnected from negative (-) battery terminal 200 Ω or higher
B133-20 (CAN+) - B133-7 (+B) R - V HIGH-level CAN bus line - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
B133-21 (CAN-) - B133-7 (+B) G - V LOW-level CAN bus line - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher



CHECK BRAKE ACTUATOR ASSEMBLY (SKID CONTROL ECU)


Refer to Terminals of ECU (Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ANTI-LOCK BRAKE SYSTEM(w/ Brake pedal Load Sensing Switch)>TERMINALS OF ECU).

a.
C358900E01
1.458,0.073 1.844,0.323 0.385,0.25 0.719,0.875 0.719,0.177 0.719,0.177 0.854,0.177 true 2.083,0.813 2.146,0.146 2.146,0.146 2.302,0.146 true 2.104,1.01 2.417,0.333 2.417,0.333 2.563,0.333 true 2.656,1 2.458,1.99 2.458,1.99 2.333,1.99 true 0.906,0.115 1.521,0.313 0.615,0.198 10 false GND2 1.521,0.104 2.135,0.302 0.615,0.198 10 false A71 2.375,0.063 2.99,0.26 0.615,0.198 10 false CANL 2.615,0.25 3.229,0.448 0.615,0.198 10 false CANH 2.052,1.906 2.667,2.104 0.615,0.198 10 false BM 0.063,0.083 0.677,0.281 0.615,0.198 10 false *a

Disconnect the brake actuator assembly (skid control ECU) connector.

Text in Illustration
*a Front view of wire harness connector
(to Brake Actuator Assembly [Skid Control ECU])


b.

Measure the resistance according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
A71-22 (CANH) - A71-10 (CANL) P - V HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) battery terminal 54 to 69 Ω
A71-22 (CANH) - A71-1 (GND2) P - W-B HIGH-level CAN bus line - Ground Cable disconnected from negative (-) battery terminal 200 Ω or higher
A71-10 (CANL) - A71-1 (GND2) V - W-B LOW-level CAN bus line - Ground Cable disconnected from negative (-) battery terminal 200 Ω or higher
A71-22 (CANH) - A71-13 (BM) P - G HIGH-level CAN bus line - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
A71-10 (CANL) - A71-13 (BM) V - G LOW-level CAN bus line - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher



CHECK COMBINATION METER ASSEMBLY


Refer to Terminals of ECU (Click hereVehicle Interior>METER / GAUGE / DISPLAY>METER / GAUGE SYSTEM>TERMINALS OF ECU).

a.
C358908E01
1.49,0.25 1.865,0.51 0.375,0.26 0.656,1.063 0.656,0.5 0.656,0.5 0.49,0.5 true 0.667,1.271 0.667,1.969 0.667,1.969 0.802,1.969 true 0.792,1.271 0.792,1.771 0.792,1.771 0.938,1.771 true 0.906,1.292 0.906,1.583 0.906,1.583 1.042,1.583 true 0.115,0.052 0.427,0.25 0.313,0.198 10 false *a 1.604,0.302 1.917,0.5 0.313,0.198 10 false J1 0.323,0.427 0.938,0.625 0.615,0.198 10 false B 1.104,1.5 1.719,1.698 0.615,0.198 10 false CANH 0.99,1.688 1.604,1.885 0.615,0.198 10 false CANL 0.833,1.885 1.448,2.083 0.615,0.198 10 false ES

Disconnect the combination meter assembly connector.

Text in Illustration
*a Front view of wire harness connector
(to Combination Meter Assembly)


b.

Measure the resistance according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Terminal Description Specified Condition
J1-23 (CANH) - J1-22 (CANL) B - W HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) battery terminal 108 to 132 Ω
J1-23 (CANH) - J1-21 (ES) B - BR HIGH-level CAN bus line - Ground Cable disconnected from negative (-) battery terminal 200 Ω or higher
J1-22 (CANL) - J1-21 (ES) W - BR LOW-level CAN bus line - Ground Cable disconnected from negative (-) battery terminal 200 Ω or higher
J1-23 (CANH) - J1-1 (B) B - R HIGH-level CAN bus line - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
J1-22 (CANL) - J1-1 (B) W - R LOW-level CAN bus line - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher



CHECK AIRBAG ECU ASSEMBLY (w/ Airbag System)


Refer to Terminals of ECU (Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM (for 3 Connectors Type)>TERMINALS OF ECU).

a.
C227529E24
0.323,0.896 0.708,1.156 0.385,0.26 0.365,2.573 0.75,2.833 0.385,0.26 1.302,1.802 1.448,1.802 1.448,1.802 1.771,1.333 true 2.417,1.646 2.26,1.646 2.26,1.646 2.104,1.333 true 2.51,3.188 2.354,3.188 2.354,3.188 2.198,2.875 true 2.583,0.542 2.417,0.542 2.417,0.542 2,0.99 true 0.135,0.104 0.448,0.302 0.313,0.198 10 false *a 0.385,0.938 0.771,1.146 0.385,0.208 10 false A58 0.448,2.625 0.833,2.833 0.385,0.208 10 false J45 0.167,1.854 0.479,2.052 0.313,0.198 10 false *b 2.646,0.469 3.26,0.667 0.615,0.198 10 false CANH 2.5,1.573 3.115,1.771 0.615,0.198 10 false CANL 1.052,1.729 1.667,1.927 0.615,0.198 10 false E1 2.573,3.115 3.188,3.313 0.615,0.198 10 false BAT

Disconnect the airbag ECU assembly connector (Click HereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM (for 3 Connectors Type)>PRECAUTION).

Text in Illustration
*a Rear view of wire harness connector
(to Airbag ECU Assembly)
*b Front view of DLC3


b.

Measure the resistance according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
A58-13 (CANH) - A58-22 (CANL) B - W HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) battery terminal 108 to 132 Ω
A58-13 (CANH) - A58-25 (E1) B - W-B HIGH-level CAN bus line - Ground Cable disconnected from negative (-) battery terminal 200 Ω or higher
A58-22 (CANL) - A58-25 (E1) W - W-B LOW-level CAN bus line - Ground Cable disconnected from negative (-) battery terminal 200 Ω or higher
A58-13 (CANH) - J45-16 (BAT) B - R HIGH-level CAN bus line - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
A58-22 (CANL) - J45-16 (BAT) W - R LOW-level CAN bus line - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher



CHECK SPIRAL WITH SENSOR CABLE SUB-ASSEMBLY (STEERING ANGLE SENSOR)


C371297N02
0.448,0.552 0.813,0.854 0.365,0.302 1.219,1.188 1.375,1.188 1.375,1.188 1.375,0.885 true 1.469,1.427 1.604,1.427 1.604,1.427 1.604,0.896 true 1.854,1.427 1.729,1.427 1.729,1.427 1.729,0.906 true 1.99,1.198 1.854,1.198 1.854,1.198 1.854,0.896 true 0.25,0.167 0.563,0.365 0.313,0.198 10 false *a 0.51,0.615 0.969,0.813 0.458,0.198 10 false J71 0.917,1.094 1.375,1.292 0.458,0.198 10 false BAT 1.063,1.344 1.521,1.542 0.458,0.198 10 false CANH 2.063,1.115 2.521,1.313 0.458,0.198 10 false ESS 1.917,1.344 2.375,1.542 0.458,0.198 10 false CANL

Text in Illustration
*a Component without harness connected
(Spiral with Sensor Cable Sub-assembly [Steering Angle Sensor])

a.
C358904E01
1.479,0.271 1.813,0.51 0.333,0.24 1.135,1.646 1.281,1.646 1.281,1.646 1.469,1.323 true 2.604,1.615 2.438,1.615 2.438,1.615 2.177,1.292 true 1.458,1.854 1.625,1.854 1.625,1.854 1.625,1.302 false 2,1.865 1.802,1.865 1.802,1.865 1.802,1.292 true 1.542,0.302 2,0.5 0.458,0.198 10 false J71 0.104,0.094 0.417,0.292 0.313,0.198 10 false *a 0.792,1.573 1.25,1.771 0.458,0.198 10 false ESS 1.083,1.781 1.542,1.979 0.458,0.198 10 false CANL 2.063,1.781 2.521,1.979 0.458,0.198 10 false CANH 2.667,1.531 3.125,1.729 0.458,0.198 10 false BAT

Disconnect the spiral with sensor cable sub-assembly (steering angle sensor) connector.

Text in Illustration
*a Front view of wire harness connector
(to Spiral with Sensor Cable Sub-assembly [Steering Angle Sensor])


b.

Measure the resistance according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
J71-4 (CANH) - J71-3 (CANL) R -G HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) battery terminal 54 to 69 Ω
J71-4 (CANH) - J71-2 (ESS) R - W-B HIGH-level CAN bus line - Ground Cable disconnected from negative (-) battery terminal 200 Ω or higher
J71-3 (CANL) - J71-2 (ESS) G - W-B LOW-level CAN bus line - Ground Cable disconnected from negative (-) battery terminal 200 Ω or higher
J71-4 (CANH) - J71-6 (BAT) R - V HIGH-level CAN bus line - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
J71-3 (CANL) - J71-6 (BAT) G - V LOW-level CAN bus line - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher



CHECK UREA SENSOR ASSEMBLY (for N04C-WA)


C407773N02
0.427,1.396 0.875,1.635 0.448,0.24 1.656,2.031 1.823,2.031 1.823,2.031 3.375,1.51 true 1.74,2.292 1.906,2.292 1.906,2.292 3.646,1.521 true 1.698,1.771 1.865,1.771 1.865,1.771 3.094,1.49 true 0.542,1.448 0.906,1.625 0.365,0.177 10 false P13 1.375,2.24 1.875,2.448 0.5,0.208 10 false CANH 1.208,1.948 1.708,2.156 0.5,0.208 10 false CANL 0.052,0.063 0.417,0.24 0.365,0.177 10 false *a 1.333,1.708 1.833,1.917 0.5,0.208 10 false GND

Text in Illustration
*a Component without harness connected
(Urea Sensor Assembly)
- -

a.
C422459N01
1.427,0.25 1.802,0.552 0.375,0.302 1.438,2.573 1.813,2.875 0.375,0.302 2.771,4.385 2.521,4.385 2.521,4.385 2.25,3.677 true 2.677,2.208 2.427,2.208 2.427,2.208 2.313,1.604 true 1.854,2.323 2.021,2.323 2.021,2.323 2.115,1.594 true 1.208,2.198 1.375,2.198 1.375,2.198 1.948,1.583 true 0.333,0.354 0.646,0.552 0.313,0.198 10 false *a 0.313,2.719 0.625,2.917 0.313,0.198 10 false *b 1.479,0.333 1.792,0.531 0.313,0.198 10 false P13 1.51,2.625 1.823,2.823 0.313,0.198 10 false J45 2.813,4.313 3.125,4.51 0.313,0.198 10 false BAT 2.74,2.135 3.24,2.344 0.5,0.208 10 false CANH 1.469,2.26 1.969,2.469 0.5,0.208 10 false CANL 0.875,2.115 1.375,2.323 0.5,0.208 10 false GND

Disconnect the urea sensor assembly connector.

Text in Illustration
*a Front view of wire harness connector
(to Urea Sensor Assembly)
*b Front view of DLC3


b.

Measure the resistance according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
P13-4 (CANH) - P13-5 (CANL) P - L HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) battery terminal 54 to 69 Ω
P13-4 (CANH) - P13-6 (GND) P - W-B HIGH-level CAN bus line - Ground Cable disconnected from negative (-) battery terminal 200 Ω or higher
P13-5 (CANL) - P13-6 (GND) L - W-B LOW-level CAN bus line - Ground Cable disconnected from negative (-) battery terminal 200 Ω or higher
P13-4 (CANH) - J45-16 (BAT) P - R HIGH-level CAN bus line - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
P13-5 (CANL) - J45-16 (BAT) L - R LOW-level CAN bus line - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher



CHECK NO. 1 NITROGEN OXIDES SENSOR (for N04C-WA)


C407772N03
3.333,0.417 3.781,0.656 0.448,0.24 4.396,0.188 4.229,0.188 4.229,0.188 3.635,1.281 true 4.635,0.5 4.469,0.5 4.469,0.5 3.906,1.26 true 2.417,0.417 2.583,0.417 2.583,0.417 3.229,1.25 true 3.417,0.479 3.781,0.656 0.365,0.177 10 false A116 4.438,0.146 4.938,0.354 0.5,0.208 10 false CANL 4.698,0.458 5.198,0.667 0.5,0.208 10 false CANH 0.073,0.094 0.438,0.271 0.365,0.177 10 false *a 2.063,0.333 2.563,0.542 0.5,0.208 10 false GND

Text in Illustration
*a Component without harness connected
(No. 1 Nitrogen Oxides Sensor)
- -

a.
C422460N01
0.365,0.927 0.792,1.188 0.427,0.26 0.354,2.469 0.781,2.729 0.427,0.26 2.667,3.083 2.5,3.083 2.5,3.083 2.323,2.792 true 2.354,1.635 2.188,1.635 2.188,1.635 2.031,1.115 true 2.229,1.844 2.063,1.844 2.063,1.844 1.813,1.156 true 1.333,1.833 1.5,1.833 1.5,1.833 1.604,1.167 true 0.49,0.281 0.802,0.479 0.313,0.198 10 false *a 0.521,1.917 0.833,2.115 0.313,0.198 10 false *b 0.406,0.948 0.781,1.146 0.375,0.198 10 false A116 0.438,2.521 0.813,2.719 0.375,0.198 10 false J45 2.708,3.01 3.083,3.208 0.375,0.198 10 false BAT 2.406,1.563 2.781,1.76 0.375,0.198 10 false GND 2.281,1.771 2.719,1.969 0.438,0.198 10 false CANL 0.927,1.771 1.448,1.979 0.521,0.208 10 false CANH

Disconnect the No. 1 nitrogen oxides sensor connector.

Text in Illustration
*a Front view of wire harness connector
(to No. 1 Nitrogen Oxides Sensor)
*b Front view of DLC3


b.

Measure the resistance according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
A116-2 (CANH) - A116-3 (CANL) P - L HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) battery terminal 54 to 69 Ω
A116-2 (CANH) - A116-4 (GND) P - W-B HIGH-level CAN bus line - Ground Cable disconnected from negative (-) battery terminal 200 Ω or higher
A116-3 (CANL) - A116-4 (GND) L - W-B LOW-level CAN bus line - Ground Cable disconnected from negative (-) battery terminal 200 Ω or higher
A116-2 (CANH) - J45-16 (BAT) P - R HIGH-level CAN bus line - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
A116-3 (CANL) - J45-16 (BAT) L - R LOW-level CAN bus line - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher



CHECK NO. 2 NITROGEN OXIDES SENSOR (for N04C-WA)


C407772N04
3.333,0.417 3.781,0.656 0.448,0.24 4.396,0.188 4.229,0.188 4.229,0.188 3.635,1.281 true 4.635,0.5 4.469,0.5 4.469,0.5 3.906,1.26 true 2.469,0.635 2.635,0.635 2.635,0.635 3.25,1.271 true 3.438,0.469 3.802,0.646 0.365,0.177 10 false P14 4.438,0.146 4.938,0.354 0.5,0.208 10 false CANL 4.698,0.458 5.198,0.667 0.5,0.208 10 false CANH 0.073,0.094 0.438,0.271 0.365,0.177 10 false *a 2.125,0.563 2.625,0.771 0.5,0.208 10 false GND

Text in Illustration
*a Component without harness connected
(No. 2 Nitrogen Oxides Sensor)
- -

a.
C422460N02
0.365,0.927 0.792,1.188 0.427,0.26 0.354,2.469 0.781,2.729 0.427,0.26 2.667,3.083 2.5,3.083 2.5,3.083 2.323,2.792 true 2.354,1.635 2.188,1.635 2.188,1.635 2.031,1.115 true 2.229,1.844 2.063,1.844 2.063,1.844 1.813,1.156 true 1.333,1.833 1.5,1.833 1.5,1.833 1.604,1.167 true 0.49,0.281 0.802,0.479 0.313,0.198 10 false *a 0.521,1.917 0.833,2.115 0.313,0.198 10 false *b 0.427,0.969 0.802,1.167 0.375,0.198 10 false P14 0.438,2.521 0.813,2.719 0.375,0.198 10 false J45 2.708,3.01 3.083,3.208 0.375,0.198 10 false BAT 2.406,1.563 2.781,1.76 0.375,0.198 10 false GND 2.281,1.771 2.656,1.969 0.375,0.198 10 false CANL 0.927,1.771 1.302,1.969 0.375,0.198 10 false CANH

Disconnect the No. 2 nitrogen oxides sensor connector.

Text in Illustration
*a Front view of wire harness connector
(to No. 2 Nitrogen Oxides Sensor)
*b Front view of DLC3


b.

Measure the resistance according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
P14-2 (CANH) - P14-3 (CANL) Y - V HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) battery terminal 54 to 69 Ω
P14-2 (CANH) - P14-4 (GND) Y - BR HIGH-level CAN bus line - Ground Cable disconnected from negative (-) battery terminal 200 Ω or higher
P14-3 (CANL) - P14-4 (GND) V - BR LOW-level CAN bus line - Ground Cable disconnected from negative (-) battery terminal 200 Ω or higher
P14-2 (CANH) - J45-16 (BAT) Y - R HIGH-level CAN bus line - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
P14-3 (CANL) - J45-16 (BAT) V - R LOW-level CAN bus line - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher



CHECK TURBOCHARGER SUB-ASSEMBLY (for N04C-WA)


C407771N02
3.396,0.177 3.854,0.427 0.458,0.25 4.073,2.146 3.906,2.146 3.906,2.146 3.51,1.229 true 2.635,2.229 2.802,2.229 2.802,2.229 3.177,1.198 true 4.417,0.49 4.25,0.49 4.25,0.49 3.885,1.115 true 3.552,0.25 4.01,0.448 0.458,0.198 10 false j5 2.25,2.167 2.708,2.365 0.458,0.198 10 false CANH 4.135,2.094 4.594,2.292 0.458,0.198 10 false CANL 0.094,0.073 0.552,0.271 0.458,0.198 10 false *a 4.5,0.417 4.958,0.615 0.458,0.198 10 false HLG

Text in Illustration
*a Component without harness connected
(Turbocharger Sub-assembly)
- -

a.
C422461N01
0.354,0.865 0.615,1.115 0.26,0.25 0.313,2.271 0.656,2.521 0.344,0.25 2.25,2.583 2.417,3 2.417,3 2.667,3 true 1.833,1.125 2.073,1.75 2.073,1.75 2.323,1.75 true 2.042,1.094 2.469,1.531 2.469,1.531 2.719,1.531 true 1.646,1.01 2.042,0.5 2.042,0.5 2.292,0.5 true 0.083,0.083 0.396,0.281 0.313,0.198 10 false *a 0.396,0.917 0.708,1.115 0.313,0.198 10 false j5 0.385,2.333 0.698,2.531 0.313,0.198 10 false J45 0.073,1.677 0.385,1.875 0.313,0.198 10 false *b 2.719,2.927 3.031,3.125 0.313,0.198 10 false BAT 2.365,1.667 2.885,1.896 0.521,0.229 10 false CANL 2.771,1.448 3.292,1.677 0.521,0.229 10 false CANH 2.354,0.427 2.875,0.656 0.521,0.229 10 false HLG

Disconnect the turbocharger sub-assembly connector.

Text in Illustration
*a Front view of wire harness connector
(to Turbocharger Sub-assembly)
*b Front view of DLC3


b.

Measure the resistance according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
j5-4 (CANH) - j5-3 (CANL) W - B HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) battery terminal 54 to 69 Ω
j5-4 (CANH) - j5-2 (HLG) W - W-B HIGH-level CAN bus line - Ground Cable disconnected from negative (-) battery terminal 200 Ω or higher
j5-3 (CANL) - j5-2 (HLG) B - W-B LOW-level CAN bus line - Ground Cable disconnected from negative (-) battery terminal 200 Ω or higher
j5-4 (CANH) - J45-16 (BAT) W - R HIGH-level CAN bus line - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
j5-3 (CANL) - J45-16 (BAT) B - R LOW-level CAN bus line - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher



CHECK EGR VALVE ASSEMBLY (for N04C-WA)


C407770N02
3.396,0.177 3.854,0.427 0.458,0.25 3.167,2.5 3.333,2.5 3.333,2.5 3.646,1.667 true 2.76,2.323 2.927,2.323 2.927,2.323 3.563,1.313 true 4.75,0.333 4.583,0.333 4.583,0.333 4.135,1.146 true 3.49,0.229 3.948,0.427 0.458,0.198 10 false B48 2.771,2.438 3.229,2.635 0.458,0.198 10 false CANH 2.396,2.271 2.854,2.469 0.458,0.198 10 false CANL 0.073,0.094 0.531,0.292 0.458,0.198 10 false *a 4.823,0.271 5.281,0.469 0.458,0.198 10 false E

Text in Illustration
*a Component without harness connected
(EGR Valve Assembly)
- -

a.
C422475N01
0.354,0.865 0.792,1.115 0.438,0.25 0.313,2.271 0.656,2.521 0.344,0.25 2.25,2.583 2.417,3 2.417,3 2.667,3 true 1.76,1.156 2,1.781 2,1.781 2.25,1.781 true 1.74,0.979 2,0.365 2,0.365 2.25,0.365 true 1.594,0.938 1.25,0.333 1.25,0.333 1.083,0.333 true 0.083,0.083 0.396,0.281 0.313,0.198 10 false *a 0.438,0.917 0.844,1.135 0.406,0.219 10 false B48 0.385,2.333 0.698,2.531 0.313,0.198 10 false J45 0.073,1.677 0.385,1.875 0.313,0.198 10 false *b 2.719,2.927 3.031,3.125 0.313,0.198 10 false BAT 2.333,0.292 2.854,0.521 0.521,0.229 10 false CANL 2.313,1.708 2.833,1.938 0.521,0.229 10 false CANH 0.948,0.26 1.469,0.49 0.521,0.229 10 false E

Disconnect the EGR valve assembly connector.

Text in Illustration
*a Front view of wire harness connector
(to EGR Valve Assembly)
*b Front view of DLC3


b.

Measure the resistance according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
B48-5 (CANH) - B48-2 (CANL) Y - V HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) battery terminal 54 to 69 Ω
B48-5 (CANH) - B48-1 (E) Y - W-B HIGH-level CAN bus line - Ground Cable disconnected from negative (-) battery terminal 200 Ω or higher
B48-2 (CANL) - B48-1 (E) V - W-B LOW-level CAN bus line - Ground Cable disconnected from negative (-) battery terminal 200 Ω or higher
B48-5 (CANH) - J45-16 (BAT) Y - R HIGH-level CAN bus line - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
B48-2 (CANL) - J45-16 (BAT) V - R LOW-level CAN bus line - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher



CHECK PARTICULATE MATTER SENSOR (for N04C-WA)


C407772N05
3.333,0.417 3.781,0.656 0.448,0.24 4.396,0.188 4.229,0.188 4.229,0.188 3.635,1.281 true 2.469,0.635 2.635,0.635 2.635,0.635 3.052,1.26 true 2.677,0.271 2.844,0.271 2.844,0.271 3.313,1.271 true 3.438,0.469 3.802,0.646 0.365,0.177 10 false P15 4.438,0.146 4.938,0.354 0.5,0.208 10 false CANH 2.292,0.198 2.792,0.406 0.5,0.208 10 false CANL 0.073,0.094 0.438,0.271 0.365,0.177 10 false *a 2.125,0.563 2.625,0.771 0.5,0.208 10 false GND

Text in Illustration
*a Component without harness connected
(Particulate Matter Sensor)
- -

a.
C422460N03
0.365,0.927 0.792,1.188 0.427,0.26 0.354,2.469 0.781,2.729 0.427,0.26 2.667,3.083 2.5,3.083 2.5,3.083 2.323,2.792 true 2.573,1.625 2.406,1.625 2.406,1.625 2.25,1.104 true 2.417,1.844 2.25,1.844 2.25,1.844 2,1.156 true 1.333,1.833 1.5,1.833 1.5,1.833 1.729,1.156 true 0.49,0.281 0.802,0.479 0.313,0.198 10 false *a 0.521,1.917 0.833,2.115 0.313,0.198 10 false *b 0.406,0.948 0.781,1.146 0.375,0.198 10 false P15 0.438,2.521 0.813,2.719 0.375,0.198 10 false J45 2.708,3.01 3.083,3.208 0.375,0.198 10 false BAT 2.625,1.552 3,1.75 0.375,0.198 10 false GND 2.458,1.771 2.833,1.969 0.375,0.198 10 false CANL 0.927,1.771 1.417,1.969 0.49,0.198 10 false CANH

Disconnect the particulate matter sensor connector.

Text in Illustration
*a Front view of wire harness connector
(to Particulate Matter Sensor)
*b Front view of DLC3


b.

Measure the resistance according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
P15-3 (CANH) - P15-4 (CANL) B - W HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) battery terminal 54 to 69 Ω
P15-3 (CANH) - P15-5 (GND) B - BR HIGH-level CAN bus line - Ground Cable disconnected from negative (-) battery terminal 200 Ω or higher
P15-4 (CANL) - P15-5 (GND) W - BR LOW-level CAN bus line - Ground Cable disconnected from negative (-) battery terminal 200 Ω or higher
P15-3 (CANH) - J45-16 (BAT) B - R HIGH-level CAN bus line - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
P15-4 (CANL) - J45-16 (BAT) W - R LOW-level CAN bus line - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher