w/ Multi-information Display:
The combination meter assembly receives engine coolant temperature signals from the ECM via the CAN communication line. The combination meter assembly displays an engine coolant temperature that is calculated based on the data received from the ECM.
w/o Multi-information Display:
The combination meter assembly controls the engine coolant temperature receiver gauge in accordance with engine coolant temperature signals from the engine coolant temperature sensor or water temperature sender gauge.
w/ Multi-information Display:
w/o Multi-information Display:
The meter/gauge system uses the CAN communication system. First, confirm that there is no malfunction in the CAN communication system. Refer to the How to Proceed with Troubleshooting procedure (w/ Multi-information Display) (Click hereVehicle Interior>METER / GAUGE / DISPLAY>METER / GAUGE SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING).
When replacing the combination meter assembly, always replace it with a new one. If a combination meter assembly which was installed to another vehicle used, the information stored in it will not match the information from the vehicle and a DTC may be stored.
| Result | Proceed to |
|---|---|
| w/ Multi-information Display | A |
| w/o Multi-information Display | B |
A
B
Check for DTCs.
for N04C-UH: See pageEngine / Hybrid System>N04C-UH (ENGINE CONTROL)>ECD SYSTEM>DTC CHECK / CLEAR
for 2TR-FE: See pageEngine / Hybrid System>2TR-FE (ENGINE CONTROL)>SFI SYSTEM>DTC CHECK / CLEAR
for N04C-WA: Click hereEngine / Hybrid System>N04C-WA (ENGINE CONTROL)>ECD SYSTEM>DTC CHECK / CLEAR
for N04C-VJ: Click hereEngine / Hybrid System>N04C-VJ (ENGINE CONTROL)>ECD SYSTEM>DTC CHECK / CLEAR
DTC is not output.
| Result | Proceed to |
|---|---|
| OK | A |
| NG (for N04C-UH) | B |
| NG (for N04C-WA) | C |
| NG (for N04C-VJ) | D |
| NG (for 2TR-FE) | E |
A
B
C
D
E
Using the GTS, perform the Active Test (Click hereVehicle Interior>METER / GAUGE / DISPLAY>METER / GAUGE SYSTEM>DATA LIST / ACTIVE TEST).
| Tester Display | Test Part | Control Range | Diagnostic Note |
|---|---|---|---|
| Water Temperature Meter Operation | Engine coolant temperature receiver gauge | OFF, Low, Normal or High | Perform the test with the vehicle stopped and the engine idling. |
Confirm that the vehicle is stopped and the engine is idling.
Needle indication is normal according to the GTS operation.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Using the GTS, read the Data List (Click hereVehicle Interior>METER / GAUGE / DISPLAY>METER / GAUGE SYSTEM>DATA LIST / ACTIVE TEST).
| Tester Display | Measurement Item/Range | Normal Condition | Diagnostic Note |
|---|---|---|---|
| Coolant Temperature | Engine coolant temperature / Min.: 0°C (0°F), Max.: 127.5°C (261.5°F) | 75 to 100°C (167 to 212°F): After warming up the engine | - |
Coolant temperature displayed on the GTS is between 75°C (167°F) and 100°C (212°F) after warming up.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Using the GTS, read the Data List (Click hereVehicle Interior>METER / GAUGE / DISPLAY>METER / GAUGE SYSTEM>DATA LIST / ACTIVE TEST).
| Tester Display | Measurement Item/Range | Normal Condition | Diagnostic Note |
|---|---|---|---|
| Coolant Temp | Engine coolant temperature / Min.: -40°C (-40°F), Max: 140°C (284°F) | 75 to 100°C (167 to 212°F): After warming up | - |
| Tester Display | Measurement Item/Range | Normal Condition | Diagnostic Note |
|---|---|---|---|
| Coolant Temperature | Engine coolant temperature / Min.: 0°C (0°F), Max.: 127.5°C (261.5°F) | 75 to 100°C (167 to 212°F): After warming up the engine | - |
"Coolant Temp" displayed on GTS is same as "Coolant Temperature" displayed on GTS.
| Result | Proceed to |
|---|---|
| OK | A |
| NG (for N04C-UH) | B |
| NG (for N04C-WA) | C |
| NG (for 2TR-FE) | D |
A
B
C
D
| Result | Proceed to |
|---|---|
| for N04C Series Engine, 2TR-FE | A |
| for 1HZ | B |
A
B
| *1 | for N04C Series Engine |
| *2 | for 2TR-FE |
| *a | Front view of wire harness connector
(to Engine Coolant Temperature Sensor) |
Disconnect the engine coolant temperature sensor connector.
Turn the ignition switch to ON, and then check the position of the receiver gauge needle.
Needle position is on COOL.
Connect terminal 3 (S) and body ground on the wire harness side connector of the engine coolant temperature sensor.
Turn the ignition switch to ON, and then check the position of the receiver gauge needle.
Needle position is on HOT.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
for N04C-UH:
Click hereEngine / Hybrid System>N04C-UH (ENGINE CONTROL)>ENGINE COOLANT TEMPERATURE SENSOR>REMOVAL
for N04C-VL:
Click hereEngine / Hybrid System>N04C-VL (ENGINE CONTROL)>ENGINE COOLANT TEMPERATURE SENSOR>REMOVAL
for N04C-VQ:
Click hereEngine / Hybrid System>N04C-VQ (ENGINE CONTROL)>ENGINE COOLANT TEMPERATURE SENSOR>REMOVAL
for 2TR-FE
Click hereEngine / Hybrid System>2TR-FE (ENGINE CONTROL)>ENGINE COOLANT TEMPERATURE SENSOR>REMOVAL
Disconnect the J1 combination meter assembly connector.
Disconnect the B57*1 or k1*2 engine coolant temperature sensor connector.
*1: for N04C Series Engine
*2: for 2TR-FE
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| J1-38 (S) - B57-3 (S)*1 | Always | Below 1 Ω |
| J1-38 (S) - k1-3 (S)*2 | Always | Below 1 Ω |
| J1-38 (S) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *a | Front view of wire harness connector
(to Water Temperature Sender Gauge) |
Disconnect the water temperature sender gauge connector.
Turn the ignition switch to ON, and then check the position of the receiver gauge needle.
Needle position is on COOL.
Connect terminal 1 (S) and body ground on the wire harness side connector of the water temperature sender gauge.
Turn the ignition switch to ON, and then check the position of the receiver gauge needle.
Needle position is on HOT.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the J1 combination meter assembly connector.
Disconnect the B7 water temperature sender gauge connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| J1-38 (S) - B7-1 (S) | Always | Below 1 Ω |
| J1-38 (S) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG