Home › Engine / Hybrid System › 2GR-FE ENGINE CONTROL › SFI SYSTEM
RM24M0E _51 Engine / Hybrid System _059540 2GR-FE ENGINE CONTROL _0291770 SFI SYSTEM C

2GR-FE ENGINE CONTROL  SFI SYSTEM  P0340  Camshaft Position Sensor Circuit Malfunction  P0342  Camshaft Position Sensor "A" Circuit Low Input (Bank 1 or Single Sensor)  P0343  Camshaft Position Sensor "A" Circuit High Input (Bank 1 or Single Sensor)  P0345  Camshaft Position Sensor "A" Circuit (Bank 2)  P0347  Camshaft Position Sensor "A" Circuit Low Input (Bank 2)  P0348  Camshaft Position Sensor "A" Circuit High Input (Bank 2)  


DESCRIPTION

The VVT sensor (for intake camshaft) (VV1, VV2 signal) consists of a magnet and MRE (Magneto Resistance Element).

The camshaft timing gear assembly has a sensor plate for the VVT sensor. When the intake camshaft rotates, changes occur in the air gaps between the timing rotor and MRE, which affects the magnetic field. As a result, the resistance of the MRE material fluctuates. The VVT sensor converts the intake camshaft rotation data to pulse signals, uses the pulse signals to determine the camshaft angle, and sends it to the ECM.

Then the ECM uses this data to control fuel injection duration, fuel injection timing and Variable Valve Timing (VVT) system.

DTC No. DTC Detection Condition Trouble Area
P0340
P0345
·

Input voltage to ECM remains 0.3 V or less, or 4.7 V or higher for more than 5 seconds, when 2 or more seconds have elapsed after turning engine switch on (IG)

(1 trip detection logic)

·

No VVT sensor signal to ECM during cranking

(1 trip detection logic)


·

Open or short in VVT sensor (for intake camshaft) circuit

·

VVT sensor (for intake camshaft)

·

Camshaft timing gear assembly

·

Valve timing

·

ECM


P0342
P0347
The output voltage of the VVT sensor is less than 0.3 V for 5 seconds (1 trip detection logic).
·

Open or short in VVT sensor (for intake camshaft) circuit

·

VVT sensor (for intake camshaft)

·

ECM


P0343
P0348
The output voltage of the VVT sensor is higher than 4.7 V for 5 seconds (1 trip detection logic).
·

Open or short in VVT sensor (for intake camshaft) circuit

·

VVT sensor (for intake camshaft)

·

ECM



WIRING DIAGRAM

CAUTION / NOTICE / HINT

HINT:
·

If no problem is found through this diagnostic troubleshooting procedure, there may be a mechanical problem with the engine.

·

Bank 1 refers to the bank that includes the No. 1 cylinder*.

*: The No. 1 cylinder is the cylinder which is farthest from the transaxle.

·

Bank 2 refers to the bank that does not include the No. 1 cylinder.

·

Read freeze frame data using the intelligent tester. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.



PROCEDURE

1.CHECK HARNESS AND CONNECTOR (SENSOR POWER SOURCE)
a.
U188248E02
2.031,2.177 2.521,2.604 false 0.167,0.125 1.49,0.427 1.323,0.302 10 false Wire Harness Side: 0.156,1.635 0.427,1.833 0.271,0.198 10 false D45 0.552,1.646 1.135,1.844 0.583,0.198 10 false Bank 1 0.156,2.563 0.448,2.76 0.292,0.198 10 false D32 0.573,2.573 1.156,2.771 0.583,0.198 10 false Bank 2 1.323,0.729 2.125,0.917 0.802,0.188 10 false VVT Sensor 1.344,2.771 2.052,2.958 0.708,0.188 10 false Front View 2.552,2.583 2.844,2.792 0.292,0.208 10 false VC

Disconnect the VVT sensor (for intake camshaft) connector.


b.

Turn the engine switch on (IG).


c.

Measure the voltage according to the value(s) in the table below.

Standard voltage:
Tester Connection Condition Specified Condition
D45-3 (VC) - Body ground Engine switch on (IG) 4.5 to 5.5 V
D32-3 (VC) - Body ground Engine switch on (IG) 4.5 to 5.5 V




OK

2.CHECK HARNESS AND CONNECTOR (VVT SENSOR (FOR INTAKE CAMSHAFT) - ECM)

NG

8.CHECK HARNESS AND CONNECTOR (VVT SENSOR (FOR INTAKE CAMSHAFT) - ECM)
2.CHECK HARNESS AND CONNECTOR (VVT SENSOR (FOR INTAKE CAMSHAFT) - ECM)
a.

Disconnect the VVT sensor (for intake camshaft) connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard resistance (Check for open):
Tester Connection Condition Specified Condition
D45-1 (VVR+) - D1-69 (VV1+) Always Below 1 Ω
D45-2 (VVR-) - D1-92 (VV1-) Always Below 1 Ω
D32-1 (VVL+) - D1-67 (VV2+) Always Below 1 Ω
D32-2 (VVL-) - D1-90 (VV2-) Always Below 1 Ω


Standard resistance (Check for short):
Tester Connection Condition Specified Condition
D45-1 (VVR+) or D1-69 (VV1+) - Body ground Always 10 kΩ or higher
D45-2 (VVR-) or D1-92 (VV1-) - Body ground Always 10 kΩ or higher
D32-1 (VVL+) or D1-67 (VV2+) - Body ground Always 10 kΩ or higher
D32-2 (VVL-) or D1-90 (VV2-) - Body ground Always 10 kΩ or higher




OK

3.CHECK VVT SENSOR FOR INTAKE CAMSHAFT (SENSOR INSTALLATION)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK VVT SENSOR FOR INTAKE CAMSHAFT (SENSOR INSTALLATION)
a.
B319222E02
0.469,1.771 0.74,1.969 0.271,0.198 10 OK 2.667,1.771 2.948,1.969 0.281,0.198 10 NG 1.719,1.552 2.396,1.76 0.677,0.208 10 Clearance

Check the VVT sensor installation condition.

OK:

Sensor is installed correctly.




OK

4.CHECK CAMSHAFT TIMING GEAR ASSEMBLY (TEETH OF PLATE)

NG

4.CHECK CAMSHAFT TIMING GEAR ASSEMBLY (TEETH OF PLATE)
a.

Check the teeth of the sensor plate.


OK:

Sensor plate teeth do not have any cracks or deformation.



OK

5.CHECK VALVE TIMING

NG

REPLACE CAMSHAFT TIMING GEAR ASSEMBLY

5.CHECK VALVE TIMING

OK

6.REPLACE VVT SENSOR

NG

ADJUST VALVE TIMING

6.REPLACE VVT SENSOR

NEXT

7.CHECK WHETHER DTC OUTPUT RECURS
7.CHECK WHETHER DTC OUTPUT RECURS
a.

Connect the intelligent tester to the DLC3.


b.

Turn the engine switch on (IG).


c.

Turn the intelligent tester on.



e.

Enter the following menus: Powertrain / Engine / DTC.


f.

Read the DTCs.

Result
Result Proceed to
DTC P0340, P0342, P0343, P0345, P0347 or P0348 is output A
DTC is not output B


HINT:

If the engine does not start, replace the ECM.



A

B

END

8.CHECK HARNESS AND CONNECTOR (VVT SENSOR (FOR INTAKE CAMSHAFT) - ECM)
a.

Disconnect the VVT sensor (for intake camshaft) connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard resistance (Check for open):
Tester Connection Condition Specified Condition
D45-3 (VC) - D1-115 (VCV1) Always Below 1 Ω
D32-3 (VC) - D1-113 (VCV2) Always Below 1 Ω


Standard resistance (Check for short):
Tester Connection Condition Specified Condition
D45-3 (VC) or D1-115 (VCV1) - Body ground Always 10 kΩ or higher
D32-3 (VC) or D1-113 (VCV2) - Body ground Always 10 kΩ or higher




OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR