Home › Engine / Hybrid System › 2GR-FE ENGINE CONTROL › SFI SYSTEM › 2013.04–2016.05
RM24M0E _51 Engine / Hybrid System _059540 2GR-FE ENGINE CONTROL _0291770 SFI SYSTEM C

2GR-FE ENGINE CONTROL  SFI SYSTEM  P0031  Oxygen (A/F) Sensor Heater Control Circuit Low (Bank 1 Sensor 1)  P0032  Oxygen (A/F) Sensor Heater Control Circuit High (Bank 1 Sensor 1)  P0051  Oxygen (A/F) Sensor Heater Control Circuit Low (Bank 2 Sensor 1)  P0052  Oxygen (A/F) Sensor Heater Control Circuit High (Bank 2 Sensor 1)  P101D  A/F Sensor Heater Circuit Performance Bank 1 Sensor 1 Stuck ON  P103D  A/F Sensor Heater Circuit Performance Bank 2 Sensor 1 Stuck ON  


DESCRIPTION

HINT:

Although the DTC titles include oxygen sensor, these DTCs relate to the air fuel ratio sensor.


The air fuel ratio sensor generates voltage* that corresponds to the actual air fuel ratio. This sensor voltage is used to provide the ECM with feedback so that it can control the air fuel ratio. The ECM determines the deviation from the stoichiometric air fuel ratio level, and regulates the fuel injection duration. If the air fuel ratio sensor malfunctions, the ECM is unable to control the air fuel ratio accurately.

The air fuel ratio sensor is a planar type and integrated with the heater, which heats the solid electrolyte (zirconia element). This heater is controlled by the ECM. When the intake air volume is low (the exhaust gas temperature is low), a current flows into the heater to heat the sensor, in order to facilitate accurate oxygen concentration detection. In addition, the sensor and heater portions are a narrow type. The heat generated by the heater is conducted to the solid electrolyte through the alumina, therefore sensor activation is accelerated.

In order to obtain a high purification rate of the carbon monoxide (CO), hydrocarbon (HC) and nitrogen oxide (NOx) components in the exhaust gas, a three-way catalytic converter is used. For the most efficient use of the three-way catalytic converter, the air fuel ratio must be precisely controlled so that it is always close to the stoichiometric level.

*: Value changes inside the ECM. Since the air fuel ratio sensor is a current output element, the current is converted into a voltage inside the ECM. Any measurements taken at the air fuel ratio sensor or ECM connectors will show a constant voltage.

A107164E60
1.646,2.385 1.938,2.385 false 1.479,2.427 0.667,2 true 2.938,2.354 3.417,2.75 true 2.729,2.177 3.417,2.333 true 2.875,1.771 3.417,1.667 true 3.094,1.656 3.417,1.333 true 2.875,2.083 3.417,2.333 true 1.115,2.948 1.24,3.146 0.125,0.198 10 false A 1.792,2.938 1.917,3.135 0.125,0.198 10 false A 0.104,1.917 0.667,2.135 0.563,0.219 10 false Element 0.094,3.115 1.01,3.333 0.917,0.219 10 false Exhaust Gas 2.573,2.969 3.865,3.177 1.292,0.208 10 false A-A Cross Section 3.5,2.25 4.927,2.469 1.427,0.219 10 false Platinum Electrode 2,2.302 2.448,2.5 0.448,0.198 10 false Cover 3.5,2.667 4.604,2.865 1.104,0.198 10 false Atmospheric Air 3.5,1.25 3.979,1.417 0.479,0.167 10 false Heater 3.5,1.583 4.667,2 1.167,0.417 10 false Solid Electrolyte (Zirconia Element) 5.729,2.833 6.604,3.052 0.875,0.219 10 false Air Fuel Ratio 5.146,0.25 7.063,0.635 1.917,0.385 10 false ECM Monitored Air Fuel Ratio Sensor Voltage 0.271,0.229 0.833,0.438 0.563,0.208 10 false Type A:

A234900E51
1.604,2.969 0.969,2.49 false 1.823,2.969 2.094,2.667 false 2.927,1.792 3.521,0.76 false 3.052,1.792 3.615,1.427 false 3.188,2.188 3.677,1.781 false 2.844,2.396 3.573,2.198 3.573,2.198 2.99,2.396 false 3.063,2.469 3.49,2.74 false 0.156,3.292 0.99,3.635 0.833,0.344 10 Exhaust Gas 0.427,2.396 0.969,2.729 0.542,0.333 10 Element 2.125,2.573 2.521,2.875 0.396,0.302 10 Cover 1.125,3.406 1.271,3.604 0.146,0.198 10 A 2.01,3.406 2.156,3.604 0.146,0.198 10 A 3.563,0.656 4.719,1.302 1.156,0.646 10 Solid Electrolyte (Zirconia Element) 3.656,1.333 4.479,1.635 0.823,0.302 10 Alumina 3.708,1.698 4.698,1.979 0.99,0.281 10 Heater 3.604,2.125 5.021,2.469 1.417,0.344 10 Platinum Electrode 3.531,2.667 4.542,3.01 1.01,0.344 10 Atmospheric Air 2.469,3.167 3.635,3.531 1.167,0.365 10 A-A Cross Section 5.677,3.125 6.573,3.469 0.896,0.344 10 Air Fuel Ratio 5.104,0.667 7.135,1.26 2.031,0.594 10 ECM Monitored Air Fuel Ratio Sensor Voltage

HINT:
·

When any of these DTCs is stored, the ECM enters fail-safe mode. The ECM turns off the air fuel ratio sensor heater in fail-safe mode. Fail-safe mode continues until the engine switch is turned off.

·

The ECM has a pulse width modulated control circuit to adjust the current through the heater. The air fuel ratio sensor heater circuit uses a relay on the +B side of the circuit.

A159612E04
0.103,0.067 3.390,0.223 3.288,0.156 10 Reference (System Diagram of Bank 1 Sensor 1): 0.448,0.887 1.303,1.029 0.855,0.142 10 from Battery 0.518,2.461 1.300,2.774 0.782,0.313 10 from EFI MAIN Relay 2.055,2.106 2.299,2.248 0.244,0.142 10 A/F 3.339,2.106 4.719,2.248 1.380,0.142 10 Air Fuel Ratio Sensor 3.423,0.792 3.621,0.962 0.198,0.170 10 +B 3.28,1.531 3.619,1.701 0.340,0.170 10 A1A- 4.433,0.792 4.816,0.962 0.383,0.170 10 HA1A 4.433,1.531 4.810,1.701 0.377,0.170 10 A1A+ 5.218,0.792 5.600,0.962 0.383,0.170 10 HA1A 5.218,1.531 5.595,1.701 0.377,0.170 10 A1A+ 5.218,2.393 5.595,2.563 0.377,0.170 10 A1A- 3.818,0.71 4.256,0.856 0.438,0.147 10 Heater 3.805,1.401 4.269,1.547 0.464,0.147 10 Sensor 5.903,0.228 6.239,0.377 0.336,0.149 10 ECM 6.309,1.545 6.778,1.861 0.468,0.316 10 Duty Control



DTC No. DTC Detection Condition Trouble Area
P0031
P0051
Air fuel ratio sensor heater current is less than 0.8 A (1 trip detection logic).
·

Open in air fuel ratio sensor (bank 1, 2 sensor 1) heater circuit

·

Air fuel ratio sensor (bank 1, 2 sensor 1)

·

A/F relay

·

ECM


P0032
P0052
Air fuel ratio sensor heater current reaches the high limit
(1 trip detection logic).
·

Short in air fuel ratio sensor (bank 1, 2 sensor 1) heater circuit

·

Air fuel ratio sensor (bank 1, 2 sensor 1)

·

A/F relay

·

ECM


P101D
P103D
Air fuel ratio sensor heater current is higher than the specified value while the heater is not operating (1 trip detection logic). ECM

WIRING DIAGRAM

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following inspection procedure.


HINT:
·

Bank 1 refers to the bank that includes the No. 1 cylinder*.

*: The No. 1 cylinder is the cylinder which is farthest from the transaxle.

·

Bank 2 refers to the bank that does not include the No. 1 cylinder.

·

Sensor 1 refers to the sensor closest to the engine assembly.

·

Sensor 2 refers to the sensor farthest away from the engine assembly.

·

Read freeze frame data using the intelligent tester. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can be helpful in determining whether the vehicle was running or stopped, whether the engine was warmed up or not, whether the air-fuel ratio was lean or rich, as well as other data recorded at the time of a malfunction.

·

Change the fuel injection volume using the Control the Injection Volume function provided in the Active Test and monitor the air fuel ratio sensor output voltage (See page Engine / Hybrid System>2GR-FE ENGINE CONTROL>SFI SYSTEM>P0136). If the sensor output voltage does not change (almost no reaction) while performing the Active Test, the sensor may be malfunctioning.



PROCEDURE

1.INSPECT AIR FUEL RATIO SENSOR (HEATER RESISTANCE)

OK

2.CHECK TERMINAL VOLTAGE (+B OF AIR FUEL RATIO SENSOR)

NG

2.CHECK TERMINAL VOLTAGE (+B OF AIR FUEL RATIO SENSOR)
a.
U188228E02
2.229,0.958 1.823,1.188 false 0.052,0.042 2.125,0.219 2.073,0.177 10 false Wire Harness Side: 0.823,0.375 2.25,0.573 1.427,0.198 10 false A/F Sensor Connector 0.198,1.021 0.469,1.198 0.271,0.177 10 false D42 0.271,1.521 0.469,1.698 0.198,0.177 10 false D8 2.26,0.823 2.531,1.021 0.271,0.198 10 false +B 0.583,0.99 1.156,1.292 0.573,0.302 10 false : Bank 1 0.583,1.51 1.156,1.813 0.573,0.302 10 false : Bank 2 2.104,1.219 2.813,1.375 0.708,0.156 10 false Front View

Disconnect the A/F sensor connector.


b.

Turn the engine switch on (IG).


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
D42-2 (+B) - Body ground Engine switch on (IG) 11 to 14 V
D8-2 (+B) - Body ground Engine switch on (IG) 11 to 14 V




OK

3.CHECK HARNESS AND CONNECTOR (AIR FUEL RATIO SENSOR - ECM)

NG

5.CHECK HARNESS AND CONNECTOR (AIR FUEL RATIO SENSOR - A/F RELAY)
3.CHECK HARNESS AND CONNECTOR (AIR FUEL RATIO SENSOR - ECM)
a.

Disconnect the air fuel ratio sensor connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for open):
Tester Connection Condition Specified Condition
D1-86 (HA1A) - D42-1 (HA1A) Always Below 1 Ω
D1-109 (HA2A) - D8-1 (HA2A) Always Below 1 Ω


Standard Resistance (Check for short):
Tester Connection Condition Specified Condition
D1-86 (HA1A) or D42-1 (HA1A) - Body ground Always 10 kΩ or higher
D1-109 (HA2A) or D8-1 (HA2A) - Body ground Always 10 kΩ or higher




OK

4.CHECK WHETHER DTC OUTPUT RECURS (DTC P0031, P0032, P0051, P0052, P101D OR P103D)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK WHETHER DTC OUTPUT RECURS (DTC P0031, P0032, P0051, P0052, P101D OR P103D)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the engine switch on (IG).


c.

Turn the tester on.


d.

Clear the DTCs.


e.

Turn the engine switch off and wait for at least 30 seconds.


f.

Start the engine.


g.

Turn the tester on.


h.

Allow the engine to idle for 1 minute or more.


i.

Enter the following menus: Powertrain / Engine / DTC.


j.

Read the DTCs.

Result
Result Proceed to
DTC is not output A
DTC P0031, P0032, P0051, P0052, P101D or P103D is output B



A

B

5.CHECK HARNESS AND CONNECTOR (AIR FUEL RATIO SENSOR - A/F RELAY)
a.

Disconnect the air fuel ratio sensor connector.


b.

Remove the A/F relay from the engine room No. 1 relay block.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for open):
Tester Connection Condition Specified Condition
D42-2 (+B) - A/F relay holder (3) Always Below 1 Ω
D8-2 (+B) - A/F relay holder (3) Always Below 1 Ω


Standard Resistance (Check for short):
Tester Connection Condition Specified Condition
D42-2 (+B) or A/F relay holder (3) - Body ground Always 10 kΩ or higher
D8-2 (+B) or A/F relay holder (3) - Body ground Always 10 kΩ or higher




OK

REPAIR OR REPLACE HARNESS OR CONNECTOR

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (A/F SENSOR - A/F RELAY)