Home › Engine / Hybrid System › 2GR-FE ENGINE CONTROL › SFI SYSTEM › 2013.04–2014.09
RM24M0E _51 Engine / Hybrid System _059540 2GR-FE ENGINE CONTROL _0291770 SFI SYSTEM C

2GR-FE ENGINE CONTROL  SFI SYSTEM  P2195  Oxygen (A/F) Sensor Signal Stuck Lean (Bank 1 Sensor 1)  P2196  Oxygen (A/F) Sensor Signal Stuck Rich (Bank 1 Sensor 1)  P2197  Oxygen (A/F) Sensor Signal Stuck Lean (Bank 2 Sensor 1)  P2198  Oxygen (A/F) Sensor Signal Stuck Rich (Bank 2 Sensor 1)  


DESCRIPTION

Refer to DTC P0031 (See page Engine / Hybrid System>2GR-FE ENGINE CONTROL>SFI SYSTEM>P0031).

DTC No. DTC Detection Condition Trouble Area
P2195
P2197
Conditions (a) and (b) continue for 5 seconds or more
(2 trip detection logic):
(a) Air fuel ratio sensor voltage is higher than 3.8 V.
(b) Heated oxygen sensor voltage is 0.15 V or higher.
·

Open or short in air fuel ratio sensor (bank 1, 2 sensor 1) circuit

·

Air fuel ratio sensor (bank 1, 2 sensor 1)

·

Intake system

·

Fuel pressure

·

Fuel injector assembly

·

ECM


While the fuel-cut operation is performed (during vehicle deceleration), the air fuel ratio sensor current is 2.2 mA or higher for 3 seconds (2 trip detection logic).
·

Air fuel ratio sensor (bank 1, 2 sensor 1)

·

ECM


P2196
P2198
Conditions (a) and (b) continue for 2 seconds or more
(2 trip detection logic):
(a) Air fuel ratio sensor voltage is less than 2.8 V.
(b) Heated oxygen sensor voltage is less than 0.6 V.
·

Open or short in air fuel ratio sensor (bank 1, 2 sensor 1) circuit

·

Air fuel ratio sensor (bank 1, 2 sensor 1)

·

Intake system

·

Fuel pressure

·

Fuel injector assembly

·

ECM


While the fuel-cut operation is performed (during vehicle deceleration), the air fuel ratio sensor current is less than 0.8 mA for 3 seconds (2 trip detection logic).
·

Air fuel ratio sensor (bank 1, 2 sensor 1)

·

ECM



HINT:
·

DTCs P2195 and P2196 indicate malfunctions related to the bank 1 air fuel ratio sensor circuit.

·

DTCs P2197 and P2198 indicate malfunctions related to the bank 2 air fuel ratio sensor circuit.

·

When any of these DTCs is stored, check the air fuel ratio sensor voltage output by entering the following menus on the intelligent tester: Powertrain / Engine / Data List / All Data / AFS Voltage B1S1 or AFS Voltage B2S1.

·

Short-term fuel trim values can also be read using the intelligent tester.

·

The ECM regulates the voltages at the A1A+, A2A+, A1A- and A2A- terminals of the ECM to a constant level. Therefore, the air fuel ratio sensor output voltage cannot be confirmed without using the intelligent tester.

·

If an air fuel ratio sensor malfunction is detected, the ECM stores a DTC.



WIRING DIAGRAM

A159613E02
5.823,0.823 6.021,1 0.198,0.177 10 false D1 5.813,1.427 6.01,1.604 0.198,0.177 10 false D1 5.813,2.406 6.01,2.583 0.198,0.177 10 false D1 5.813,3.167 6.01,3.344 0.198,0.177 10 false D1 5.813,3.75 6.01,3.927 0.198,0.177 10 false D1 5.813,4.719 6.01,4.896 0.198,0.177 10 false D1 6.115,0.667 6.51,0.844 0.396,0.177 10 false HA1A 4.188,0.688 4.583,0.865 0.396,0.177 10 false HA1A 3.292,0.688 3.688,0.865 0.396,0.177 10 false +B 6.115,1.292 6.51,1.469 0.396,0.177 10 false A1A+ 4.177,1.24 4.573,1.417 0.396,0.177 10 false A1A+ 3.146,1.719 4.802,2.052 1.656,0.333 10 false D42 Air Fuel Ratio Sensor (Bank 1 Sensor 1) 3.292,1.229 3.688,1.406 0.396,0.177 10 false A1A- 5.823,0.625 6.146,0.802 0.323,0.177 10 false 86 5.823,1.229 6.146,1.406 0.323,0.177 10 false 93 4.604,0.917 4.927,1.094 0.323,0.177 10 false 1 5.125,1.031 5.448,1.208 0.323,0.177 10 false * 5.313,3.417 5.635,3.594 0.323,0.177 10 false * 4.604,1.51 4.927,1.688 0.323,0.177 10 false 3 3.115,0.917 3.438,1.094 0.323,0.177 10 false 2 1.813,0.688 2.135,0.865 0.323,0.177 10 false 3 1.813,1.354 2.135,1.531 0.323,0.177 10 false 2 1.219,0.688 1.542,0.865 0.323,0.177 10 false 5 1.219,1.354 1.542,1.531 0.323,0.177 10 false 1 1.438,1.5 1.76,1.677 0.323,0.177 10 false A/F 1.813,2.979 2.135,3.156 0.323,0.177 10 false 5 1.813,3.635 2.135,3.813 0.323,0.177 10 false 2 1.219,2.979 1.542,3.156 0.323,0.177 10 false 3 1.219,3.635 1.542,3.813 0.323,0.177 10 false 1 1.208,3.802 1.844,4.156 0.635,0.354 10 false EFI MAIN 1.74,4.104 2.063,4.281 0.323,0.177 10 false EFI 0.552,6.229 1.167,6.406 0.615,0.177 10 false FL MAIN 0.667,6.979 1.167,7.167 0.5,0.188 10 false Battery 0.552,5.656 1.26,5.813 0.708,0.156 10 false F/B BATT 3.323,6.688 4.031,7.021 0.708,0.333 10 false *: Shielded 0.552,1.229 0.833,1.406 0.281,0.177 10 false A/F 3.115,1.5 3.438,1.677 0.323,0.177 10 false 4 6.115,2.281 6.51,2.458 0.396,0.177 10 false A1A- 5.792,2.219 6.115,2.396 0.323,0.177 10 false 116 6.115,3.01 6.51,3.188 0.396,0.177 10 false HA2A 4.188,3.031 4.583,3.208 0.396,0.177 10 false HA2A 3.292,3.031 3.688,3.208 0.396,0.177 10 false +B 6.115,3.635 6.51,3.813 0.396,0.177 10 false A2A+ 4.177,3.583 4.573,3.76 0.396,0.177 10 false A2A+ 3.146,4.052 4.729,4.396 1.583,0.344 10 false D8 Air Fuel Ratio Sensor (Bank 2 Sensor 1) 3.292,3.573 3.688,3.75 0.396,0.177 10 false A2A- 5.781,2.969 6.104,3.146 0.323,0.177 10 false 109 5.781,3.563 6.104,3.74 0.323,0.177 10 false 120 4.604,3.25 4.927,3.427 0.323,0.177 10 false 1 4.604,3.844 4.927,4.021 0.323,0.177 10 false 3 3.115,3.25 3.438,3.427 0.323,0.177 10 false 2 3.115,3.833 3.438,4.01 0.323,0.177 10 false 4 6.115,4.594 6.51,4.771 0.396,0.177 10 false A2A- 6.115,5.479 6.594,5.656 0.479,0.177 10 false MREL 6.292,6.094 6.771,6.271 0.479,0.177 10 false ECM 5.781,4.531 6.104,4.708 0.323,0.177 10 false 119 5.813,5.51 6.135,5.688 0.323,0.177 10 false A7 5.823,5.323 6.146,5.5 0.323,0.177 10 false 44

CONFIRMATION DRIVING PATTERN

A293210E11
2.469,1.51 2.917,0.76 2.917,0.76 2.708,0.76 false 4.438,1.521 5.052,1.521 false 4.51,0.625 4.896,1.781 false 5.865,0.865 5.448,1.656 false 5.385,2.198 6.396,2.198 false 3.958,3.354 4.365,3.563 false 0.135,0.188 3.135,0.448 3,0.26 10 false Engine Coolant Temperature: 75°C or higher 1.083,0.677 2.844,1.031 1.76,0.354 10 false Between 60 and 100 km/h 0.75,2.281 1.302,2.698 0.552,0.417 10 false Idling 1.26,2.781 2.177,3.219 0.917,0.438 10 false Warming up 2.479,2.792 3.188,3.302 0.708,0.51 10 false 10 minutes or more 0.177,0.917 1.219,1.292 1.042,0.375 10 false Vehicle Speed 1.302,2.146 1.719,2.531 0.417,0.385 10 false [A] 2.75,1.302 3.167,1.688 0.417,0.385 10 false [B] 3.563,2.115 3.979,2.5 0.417,0.385 10 false [C] 5.135,1.281 5.552,1.667 0.417,0.385 10 false [D] 5.521,1.667 5.938,2.052 0.417,0.385 10 false [E] 4.667,0.813 5.688,1.115 1.021,0.302 10 false At least 3 times 3.385,0.479 4.5,0.969 1.115,0.49 10 false Accelerator Pedal Depressed 3.406,1.427 4.479,1.688 1.073,0.26 10 false 60 km/h or more 5.76,0.479 6.969,0.99 1.208,0.51 10 false Accelerator Pedal Released (Fuel-cut) 6.438,2.115 6.99,2.375 0.552,0.26 10 false 10 km/h 6.229,2.552 6.781,2.813 0.552,0.26 10 false Time 4.604,2.792 5.365,3.229 0.76,0.438 10 false 10 seconds or more 5.448,2.792 6.094,3.167 0.646,0.375 10 true 4 seconds or more 4.406,3.51 5.802,3.802 1.396,0.292 10 false Refer to figure below 6.083,3.146 6.635,3.406 0.552,0.26 10 false [F]

A232909E51
3.635,2.625 3.958,0.896 false 3.365,2.625 2.156,0.719 2.156,0.719 2.281,0.719 false 0.104,0.042 3.042,0.24 2.938,0.198 10 false Driving Pattern Detail for [C] through [E]: 0.177,0.563 1.948,0.76 1.771,0.198 10 false Reference Engine Speed 2.813,0.156 6.969,0.354 4.156,0.198 10 false Cumulative Detection Period "t" = t1 + t2 + t3 = 3 seconds or more 0.833,1.854 1.604,2.052 0.771,0.198 10 false 2500 rpm 0.833,2.208 1.604,2.406 0.771,0.198 10 false 1400 rpm 1.094,2.406 1.51,2.604 0.417,0.198 10 false Idling 2.188,2.969 2.604,3.167 0.417,0.198 10 false Idling 3.188,3.094 3.885,3.458 0.698,0.365 10 false 4 seconds or more 4.406,3.094 5.094,3.458 0.688,0.365 10 false 4 seconds or more 5.625,3.125 6.333,3.49 0.708,0.365 10 false 4 seconds or more 2.188,2.51 2.406,2.708 0.219,0.198 10 false [C] 2.823,1.156 3.063,1.354 0.24,0.198 10 false [D] 3.458,1.542 3.656,1.74 0.198,0.198 10 false [E] 2.365,0.615 3.552,0.813 1.188,0.198 10 false Delay (3 seconds) 4,0.781 5.438,0.979 1.438,0.198 10 false Detection Period t1 4.813,2.438 4.969,2.635 0.156,0.198 10 false t2 6.031,2.438 6.188,2.635 0.156,0.198 10 false t3 6.479,2.802 6.865,3 0.385,0.198 10 false Time

1.

Connect the intelligent tester to the DLC3.

2.

Turn the engine switch on (IG).

3.

Turn the tester on.

4.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

5.

Turn the engine switch off and wait for at least 30 seconds.

6.

Turn the engine switch on (IG) and turn the tester on.

7.

Start the engine and warm it up until the engine coolant temperature reaches 75°C (167°F) or higher [A].

8.

On the tester, enter the following menus to check the fuel-cut status: Powertrain / Engine / Data List / All Data / Idle Fuel Cut.

9.

Drive the vehicle at a speed between 60 and 100 km/h (37 and 62 mph) for at least 10 minutes [B].

CAUTION:

When performing the confirmation driving pattern, obey all speed limits and traffic laws.


10.

With the shift lever in S [C], accelerate the vehicle to 60 km/h (37 mph) or more by depressing the accelerator pedal for at least 10 seconds [D].

CAUTION:

When performing the confirmation driving pattern, obey all speed limits and traffic laws.


11.

Soon after performing step [D] above, release the accelerator pedal for at least 4 seconds without depressing the brake pedal in order to execute fuel-cut control [E].

HINT:

Fuel-cut is performed when the following conditions are met:

·

Accelerator pedal is fully released.

·

Fuel injection returns at 1400 rpm.



12.

Allow the vehicle to decelerate until the vehicle speed decreases to less than 10 km/h (6 mph).

13.

Repeat steps [C] through [E] above at least 3 times in one driving cycle.

14.

Enter the following menus: Powertrain / Engine / DTC [F].

15.

Read the pending DTCs.

HINT:
·

If a pending DTC is output, the system is malfunctioning.

·

If a pending DTC is not output, perform the following procedure.



16.

Enter the following menus: Powertrain / Engine / Utility / All Readiness.

17.

Input the DTC: P2195, P2196, P2197 or P2198.

18.

Check the DTC judgment result.

Tester Display Description
NORMAL
·

DTC judgment completed

·

System normal


ABNORMAL
·

DTC judgment completed

·

System abnormal


INCOMPLETE
·

DTC judgment not completed

·

Perform driving pattern after confirming DTC enabling conditions


N/A
·

Unable to perform DTC judgment

·

Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit



HINT:
·

If the judgment result shows NORMAL, the system is normal.

·

If the judgment result shows ABNORMAL, the system has a malfunction.

·

If the judgment result shows INCOMPLETE or N/A, perform steps [B] through [F] again.




CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following inspection procedure.


HINT:
·

Read freeze frame data using the intelligent tester. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can be helpful in determining whether the vehicle was running or stopped, whether the engine was warmed up or not, whether the air-fuel ratio was lean or rich, as well as other data recorded at the time of a malfunction.

·

A low air fuel ratio sensor voltage could be caused by a rich air fuel mixture. Check for conditions that would cause the engine to run rich.

·

A high air fuel ratio sensor voltage could be caused by a lean air fuel mixture. Check for conditions that would cause the engine to run lean.

·

Bank 1 refers to the bank that includes the No. 1 cylinder*.

*: The No. 1 cylinder is the cylinder which is farthest from the transaxle.

·

Bank 2 refers to the bank that does not include the No. 1 cylinder.

·

Sensor 1 refers to the sensor closest to the engine assembly.

·

Sensor 2 refers to the sensor farthest away from the engine assembly.



PROCEDURE

1.CHECK ANY OTHER DTCS OUTPUT (IN ADDITION TO DTC P2195, P2196, P2197 OR P2198)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the engine switch on (IG).


c.

Turn the tester on.


d.

Enter the following menus: Powertrain / Engine / DTC.


e.

Read the DTCs.

Result
Result Proceed to
DTC P2195, P2196, P2197 or P2198 is output A
DTC P2195, P2196, P2197 or P2198 and P0136, P0137, P0138, P0156, P0157 or P0158 are output A
DTC P2195, P2196, P2197 or P2198 and other DTCs are output B

HINT:

If any DTCs relating to the air fuel ratio sensor (DTCs for the air fuel ratio sensor heater or air fuel ratio sensor admittance) are output, troubleshoot those DTCs first.




A

2.CONFIRM IF VEHICLE HAS RUN OUT OF FUEL IN PAST

B

2.CONFIRM IF VEHICLE HAS RUN OUT OF FUEL IN PAST
a.

Has the vehicle run out of fuel in the past?



YES

3.CHECK WHETHER DTC OUTPUT RECURS (DTC P2195, P2196, P2197 OR P2198)

NO

4.READ VALUE USING INTELLIGENT TESTER (TEST VALUE OF AIR FUEL RATIO SENSOR)
3.CHECK WHETHER DTC OUTPUT RECURS (DTC P2195, P2196, P2197 OR P2198)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the engine switch on (IG).


c.

Turn the tester on.



e.

Turn the engine switch off and wait for at least 30 seconds.


f.

Turn the engine switch on (IG) and turn the tester on.


g.

Start the engine and warm it up.


h.

Drive the vehicle in accordance with the driving pattern described in the Confirmation Driving Pattern.


i.

Enter the following menus: Powertrain / Engine / Utility / All Readiness.


j.

Input the DTC: P2195, P2196, P2197 or P2198.


k.

Check the DTC judgment result.

Result
Result Proceed to
NORMAL (DTC is not output) A
ABNORMAL (DTC P2195, P2196, P2197 or P2198 is output) B



A

DTC CAUSED BY RUNNING OUT OF FUEL

B

4.READ VALUE USING INTELLIGENT TESTER (TEST VALUE OF AIR FUEL RATIO SENSOR)
4.READ VALUE USING INTELLIGENT TESTER (TEST VALUE OF AIR FUEL RATIO SENSOR)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the engine switch on (IG).


c.

Turn the tester on.



e.

Drive the vehicle in accordance with the driving pattern described in the Confirmation Driving Pattern.


f.

Enter the following menus: Powertrain / Engine / Data List / All Data / AFS Current B1S1 or AFS Current B2S1.


g.

Check the test value of the air fuel ratio sensor output current during fuel-cut.

Result
Test Value Proceed to
Within normal range (0.8 mA or higher, and less than 2.2 mA) A
Outside normal range (Less than 0.8 mA, or 2.2 mA or higher) B



A

5.READ VALUE USING INTELLIGENT TESTER (OUTPUT VOLTAGE OF AIR FUEL RATIO SENSOR)

B

14.REPLACE AIR FUEL RATIO SENSOR
5.READ VALUE USING INTELLIGENT TESTER (OUTPUT VOLTAGE OF AIR FUEL RATIO SENSOR)
a.

Connect the intelligent tester to the DLC3.


b.

Start the engine.


c.

Turn the tester on.


d.

Warm up the air fuel ratio sensor at an engine speed of 2500 rpm for 90 seconds.


e.

Enter the following menus: Powertrain / Engine / Active Test / Control the Injection Volume for A/F Sensor / All Data / AFS Voltage B1S1 and O2S B1S2 or AFS Voltage B2S1 and O2S B2S2.


f.

Perform the Control the Injection Volume operation with the engine idling.


g.

Monitor the output voltages of the air fuel ratio and heated oxygen sensors (AFS Voltage B1S1 and O2S B1S2 or AFS Voltage B2S1 and O2S B2S2) displayed on the tester.

HINT:
·

The Control the Injection Volume for A/F Sensor operation lowers the fuel injection volume by 12.5% or increases the injection volume by 12.5%.

·

The air fuel ratio sensor has an output delay of a few seconds and the heated oxygen sensor has a maximum output delay of approximately 20 seconds.

·

If the sensor output voltage does not change (almost no reaction) while performing the Active Test, the sensor may be malfunctioning.



Tester Display
(Sensor)
Injection Volume Status Voltage
AFS Voltage B1S1
AFS Voltage B2S1
(Air fuel ratio)
12.5% Rich Below 3.1 V
-12.5% Lean Higher than 3.4 V
O2S B1S2
O2S B2S2
(Heated oxygen)
12.5% Rich Higher than 0.55 V
-12.5% Lean Below 0.4 V

Result
Status of AFS Voltage B1S1 or AFS Voltage B2S1 Status of O2S B1S2 or O2S B2S2 Air Fuel Ratio Condition and Air Fuel Ratio Sensor Condition Proceed to
Lean Lean Actual air fuel ratio lean A
Rich Rich Actual air fuel ratio rich A
Lean Lean/Rich Air fuel ratio sensor malfunction B
Rich Lean/Rich Air fuel ratio sensor malfunction B
Lean/Rich Lean/Rich Normal B

Lean: During the Control the Injection Volume for A/F Sensor Active Test, the air fuel ratio sensor output voltages (AFS Voltage B1S1 and AFS Voltage B2S1) are consistently higher than 3.4 V, and the heated oxygen sensor output voltages (O2S B1S2 and O2S B2S2) are consistently below 0.4 V.

Rich: During the Control the Injection Volume for A/F Sensor Active Test, the AFS Voltage B1S1 and AFS Voltage B2S1 are consistently below 3.1 V, and the O2S B1S2 and O2S B2S2 are consistently higher than 0.55 V.

Lean/Rich: During the Control the Injection Volume for A/F Sensor Active Test, the output voltage of the heated oxygen sensor alternates correctly.


HINT:

Refer to "Data List / Active Test" [AFS Voltage B1S1, AFS Voltage B2S1, O2S B1S2 and O2S B2S2] (See page Engine / Hybrid System>2GR-FE ENGINE CONTROL>SFI SYSTEM>DATA LIST / ACTIVE TEST).




A

6.CHECK INTAKE SYSTEM

B

14.REPLACE AIR FUEL RATIO SENSOR
6.CHECK INTAKE SYSTEM
a.

Check the intake system for vacuum leaks.

OK:

No leaks in the intake system.




OK

7.CHECK FOR EXHAUST GAS LEAK

NG

REPAIR OR REPLACE INTAKE SYSTEM

7.CHECK FOR EXHAUST GAS LEAK
a.

Check for exhaust gas leaks.

OK:

No gas leaks.




OK

8.CHECK FUEL PRESSURE

NG

REPAIR OR REPLACE EXHAUST SYSTEM

8.CHECK FUEL PRESSURE

OK

9.INSPECT FUEL INJECTOR ASSEMBLY

NG

16.CHECK FUEL LINE
9.INSPECT FUEL INJECTOR ASSEMBLY
a.

Inspect the fuel injector assembly injection (whether fuel volume is high or low, and whether injector pattern is poor) (See page Engine / Hybrid System>2GR-FE FUEL>FUEL INJECTOR>INSPECTION).



OK

10.REPLACE AIR FUEL RATIO SENSOR

NG

REPLACE FUEL INJECTOR ASSEMBLY

10.REPLACE AIR FUEL RATIO SENSOR
a.


NEXT

11.CHECK WHETHER DTC OUTPUT RECURS (DTC P2195, P2196, P2197 OR P2198)
11.CHECK WHETHER DTC OUTPUT RECURS (DTC P2195, P2196, P2197 OR P2198)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the engine switch on (IG).


c.

Turn the tester on.



e.

Turn the engine switch off and wait for at least 30 seconds.


f.

Turn the engine switch on (IG) and turn the tester on.


g.

Start the engine and warm it up.


h.

Drive the vehicle in accordance with the driving pattern described in the Confirmation Driving Pattern.


i.

Enter the following menus: Powertrain / Engine / Utility / All Readiness.


j.

Input the DTC: P2195, P2196, P2197 or P2198.


k.

Check the DTC judgment result.

Result
Result Proceed to
ABNORMAL (DTC P2195, P2196, P2197 or P2198 is output) A
NORMAL (DTC is not output) B



A

12.REPLACE ECM

B

END

12.REPLACE ECM

NEXT

13.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
13.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
a.

Connect the intelligent tester to the DLC3.


b.

Turn the engine switch on (IG).


c.

Turn the tester on.



e.

Turn the engine switch off and wait for at least 30 seconds.


f.

Turn the engine switch on (IG) and turn the tester on.


g.

Start the engine and warm it up.


h.

Drive the vehicle in accordance with the driving pattern described in the Confirmation Driving Pattern.


i.

Enter the following menus: Powertrain / Engine / Utility / All Readiness.


j.

Input the DTC: P2195, P2196, P2197 or P2198.


k.

Check the DTC judgment result.

Result
Tester Display Description
NORMAL
·

DTC judgment completed

·

System normal


ABNORMAL
·

DTC judgment completed

·

System abnormal


INCOMPLETE
·

DTC judgment not completed

·

Perform driving pattern after confirming DTC enabling conditions


N/A
·

Unable to perform DTC judgment

·

Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit





NEXT

END

14.REPLACE AIR FUEL RATIO SENSOR
a.


NEXT

15.CHECK WHETHER DTC OUTPUT RECURS (DTC P2195, P2196, P2197 OR P2198)
15.CHECK WHETHER DTC OUTPUT RECURS (DTC P2195, P2196, P2197 OR P2198)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the engine switch on (IG).


c.

Turn the tester on.



e.

Turn the engine switch off and wait for at least 30 seconds.


f.

Turn the engine switch on (IG) and turn the tester on.


g.

Start the engine and warm it up.


h.

Drive the vehicle in accordance with the driving pattern described in the Confirmation Driving Pattern.


i.

Enter the following menus: Powertrain / Engine / Utility / All Readiness.


j.

Input the DTC: P2195, P2196, P2197 or P2198.


k.

Check the DTC judgment result.

Result
Result Proceed to
NORMAL (DTC is not output) A
ABNORMAL (DTC P2195, P2196, P2197 or P2198 is output) B



A

END

B

16.CHECK FUEL LINE
a.

Check the fuel lines for leaks or blockage.



OK

NG

REPAIR OR REPLACE FUEL LINE