Home › Engine / Hybrid System › 2GR-FE ENGINE CONTROL › SFI SYSTEM › 2013.04–2014.09
RM24M0E _51 Engine / Hybrid System _059540 2GR-FE ENGINE CONTROL _0291770 SFI SYSTEM C

2GR-FE ENGINE CONTROL  SFI SYSTEM  P0136  Oxygen Sensor Circuit Malfunction (Bank 1 Sensor 2)  P0137  Oxygen Sensor Circuit Low Voltage (Bank 1 Sensor 2)  P0138  Oxygen Sensor Circuit High Voltage (Bank 1 Sensor 2)  P0156  Oxygen Sensor Circuit Malfunction (Bank 2 Sensor 2)  P0157  Oxygen Sensor Circuit Low Voltage (Bank 2 Sensor 2)  P0158  Oxygen Sensor Circuit High Voltage (Bank 2 Sensor 2)  


DESCRIPTION

Refer to DTC P0037 (See page Engine / Hybrid System>2GR-FE ENGINE CONTROL>SFI SYSTEM>P0037).

DTC No. DTC Detection Condition Trouble Area
P0136
P0156
Abnormal voltage output:

During active air fuel ratio control, following conditions (a) and (b) are met for a certain period of time (2 trip detection logic):

(a)

Heated oxygen sensor voltage does not decrease to less than 0.21 V

(b)

Heated oxygen sensor voltage does not increase to 0.6 V or higher



·

Heated oxygen sensor (bank 1, 2 sensor 2) circuit

·

Heated oxygen sensor (bank 1, 2 sensor 2)

·

Air fuel ratio sensor (bank 1, 2 sensor 1)

·

Gas leak from exhaust system

·

Fuel pressure

·

Fuel injector assembly

·

PCV valve and hose

·

Intake system


P0137
P0157
Low voltage (open):

During active air fuel ratio control, following conditions (a) and (b) are met for a certain period of time (2 trip detection logic):

(a)

Heated oxygen sensor voltage output less than 0.21 V

(b)

Target air fuel ratio rich



·

Heated oxygen sensor (bank 1, 2 sensor 2) circuit

·

Heated oxygen sensor (bank 1, 2 sensor 2)

·

Air fuel ratio sensor (bank 1, 2 sensor 1)

·

Gas leak from exhaust system


P0138
P0158
High voltage (short):

During active air fuel ratio control, following conditions (a) and (b) are met for a certain period of time (2 trip detection logic):

(a)

Heated oxygen sensor voltage output higher than 0.6 V

(b)

Target air fuel ratio lean



·

Heated oxygen sensor (bank 1, 2 sensor 2) circuit

·

Heated oxygen sensor (bank 1, 2 sensor 2)

·

Air fuel ratio sensor (bank 1, 2 sensor 1)

·

ECM



CONFIRMATION DRIVING PATTERN

HINT:
·

This confirmation driving pattern is used in the "Perform Confirmation Driving Pattern" procedure of the following diagnostic troubleshooting procedure.

·

Performing this confirmation driving pattern will activate the heated oxygen sensor monitor (the catalyst monitor is performed simultaneously). This is very useful for verifying the completion of a repair.



A200170E36
2.708,2.375 2.958,2.583 0.25,0.208 10 false [B] 4.135,0.729 4.406,0.979 0.271,0.25 10 false [C] 5.083,3.104 5.417,3.344 0.333,0.24 10 false [D] 1.042,0.5 1.708,0.719 0.667,0.219 10 false 100 km/h 1.094,1.375 2.135,1.594 1.042,0.219 10 false 60 km/h 1.271,2.156 1.667,2.51 0.396,0.354 10 false Idling 0.24,2.5 1.698,2.771 1.458,0.271 10 false Engine Switch on (IG) 2.438,3.135 3.271,3.396 0.833,0.26 10 false Warming up 3.604,3.198 4.875,3.479 1.271,0.281 10 false 10 minutes or more 2.073,2.552 2.292,2.771 0.219,0.219 10 false [A]

1.

Connect the intelligent tester to the DLC3.

2.

Turn the engine switch on (IG) and turn the tester on.

3.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

4.

Turn the engine switch off and wait for at least 30 seconds.

5.

Turn the engine switch on (IG) and turn the tester on [A].

6.

Start the engine and warm it up until the engine coolant temperature reaches 75°C (167°F) or higher [B].

7.

With the shift lever in D, drive the vehicle at 60 to 100 km/h (37 to 62 mph) for 10 minutes or more [C].

CAUTION:

When performing the confirmation driving pattern, obey all speed limits and traffic laws.


8.

Enter the following menus: Powertrain / Engine / DTC [D].

9.

Read the pending DTCs.

HINT:
·

If a pending DTC is output, the system is malfunctioning.

·

If a pending DTC is not output, perform the following procedure.



10.

Enter the following menus: Powertrain / Engine / Utility / All Readiness.

11.

Input the DTC: P0136, P0137, P0138, P0156, P0157 or P0158.

12.

Check the DTC judgment result.

Tester Display Description
NORMAL
·

DTC judgment completed

·

System normal


ABNORMAL
·

DTC judgment completed

·

System abnormal


INCOMPLETE
·

DTC judgment not completed

·

Perform driving pattern after confirming DTC enabling conditions


N/A
·

Unable to perform DTC judgment

·

Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit



HINT:
·

If the judgment result shows NORMAL, the system is normal.

·

If the judgment result shows ABNORMAL, the system has a malfunction.

·

If the judgment result shows INCOMPLETE or N/A, perform steps [C] and [D] again.




WIRING DIAGRAM

A159614E02
6.26,8.55 6.590,8.703 0.330,0.152 10 ECM 1.188,1.669 1.483,1.821 0.295,0.152 10 G53 1.188,1.816 3.830,1.968 2.642,0.152 10 Heated Oxygen Sensor (Bank 1 Sensor 2) 5.542,0.691 5.742,0.844 0.200,0.152 10 D1 5.542,1.44 5.742,1.592 0.200,0.152 10 D1 5.542,2.439 5.742,2.591 0.200,0.152 10 D1 5.542,3.195 5.742,3.347 0.200,0.152 10 D1 5.542,3.924 5.742,4.076 0.200,0.152 10 D1 5.542,4.947 5.742,5.099 0.200,0.152 10 D1 4.819,0.794 5.001,0.947 0.181,0.152 10 *1 4.819,3.279 5.001,3.431 0.181,0.152 10 *1 5.896,0.558 6.278,0.711 0.382,0.152 10 HT1B 2.879,0.6 3.261,0.753 0.382,0.152 10 HT1B 1.758,0.6 1.977,0.753 0.218,0.152 10 +B 1.594,0.577 1.711,0.729 0.118,0.152 10 1 3.302,0.591 3.419,0.743 0.118,0.152 10 2 2.849,1.348 3.260,1.500 0.412,0.152 10 OX1B 1.758,1.348 1.977,1.500 0.218,0.152 10 E2 1.594,1.324 1.711,1.477 0.118,0.152 10 3 3.302,1.338 3.419,1.491 0.118,0.152 10 4 1.188,4.149 1.483,4.301 0.295,0.152 10 D39 1.188,4.296 3.830,4.448 2.642,0.152 10 Heated Oxygen Sensor (Bank 2 Sensor 2) 2.879,3.085 3.261,3.237 0.382,0.152 10 HT2B 1.758,3.085 1.977,3.237 0.218,0.152 10 +B 1.594,3.076 1.711,3.228 0.118,0.152 10 2 3.302,3.076 3.419,3.228 0.118,0.152 10 1 2.849,3.832 3.260,3.985 0.412,0.152 10 OX2B 1.758,3.832 1.977,3.985 0.218,0.152 10 E2 1.594,3.823 1.711,3.975 0.118,0.152 10 4 3.302,3.823 3.419,3.975 0.118,0.152 10 3 3.81,5.781 3.927,5.933 0.118,0.152 10 3 2.944,5.781 3.062,5.933 0.118,0.152 10 5 3.81,6.254 3.927,6.406 0.118,0.152 10 1 2.944,6.254 3.062,6.406 0.118,0.152 10 2 5.56,0.488 5.736,0.641 0.177,0.152 10 48 5.896,1.43 6.309,1.583 0.413,0.152 10 OX1B 5.56,1.224 5.736,1.376 0.177,0.152 10 88 5.896,2.446 6.278,2.599 0.382,0.152 10 EX1B 5.56,2.24 5.736,2.392 0.177,0.152 10 65 5.896,3.052 6.278,3.205 0.382,0.152 10 HT2B 5.56,2.982 5.736,3.135 0.177,0.152 10 47 5.553,6.345 5.743,6.497 0.191,0.152 10 A7 5.896,6.268 6.302,6.420 0.406,0.152 10 MREL 3.115,6.681 3.743,6.833 0.628,0.152 10 EFI MAIN 0.782,6.033 1.410,6.185 0.628,0.152 10 F/B BATT 0.495,6.835 1.071,6.987 0.576,0.152 10 FL MAIN 0.565,7.858 1.047,8.010 0.482,0.152 10 Battery 2.898,7.543 3.699,7.695 0.802,0.152 10 *1: Shielded 2.033,6.026 2.293,6.178 0.260,0.152 10 EFI 5.56,6.141 5.736,6.294 0.177,0.152 10 44 5.896,3.924 6.309,4.077 0.413,0.152 10 OX2B 5.56,3.718 5.736,3.870 0.177,0.152 10 87 5.896,4.94 6.278,5.093 0.382,0.152 10 EX2B 5.56,4.733 5.736,4.886 0.177,0.152 10 64

CAUTION / NOTICE / HINT

HINT:

Malfunctioning areas can be identified by performing the Control the Injection Volume for A/F Sensor function provided in the Active Test. The Control the Injection Volume for A/F Sensor function can help to determine whether the air fuel ratio sensor, heated oxygen sensor and other potential trouble areas are malfunctioning.

The following instructions describe how to conduct the Control the Injection Volume for A/F Sensor operation using the intelligent tester.

1.

Connect the intelligent tester to the DLC3.

2.

Start the engine.

3.

Turn the tester on.

4.

Warm up the engine at an engine speed of 2500 rpm for approximately 90 seconds.

5.

Enter the following menus: Powertrain / Engine / Active Test / Control the Injection Volume for A/F Sensor / All Data / AFS Voltage B1S1 and O2S B1S2 or AFS Voltage B2S1 and O2S B2S2.

6.

Perform the Active Test operation with the engine idling (press the RIGHT or LEFT button to change the fuel injection volume).

7.

Monitor the output voltages of the air fuel ratio and heated oxygen sensors (AFS Voltage B1S1 and O2S B1S2 or AFS Voltage B2S1 and O2S B2S2) displayed on the tester.



HINT:
·

The Control the Injection Volume for A/F Sensor operation lowers the fuel injection volume by 12.5% or increases the injection volume by 12.5%.

·

Each sensor reacts in accordance with increases and decreases in the fuel injection volume.



Tester Display
(Sensor)
Injection Volume Status Voltage
AFS Voltage B1S1
AFS Voltage B2S1
(Air fuel ratio)
12.5% Rich Below 3.1 V
-12.5% Lean Higher than 3.4 V
O2S B1S2
O2S B2S2
(Heated oxygen)
12.5% Rich Higher than 0.55 V
-12.5% Lean Below 0.4 V

NOTICE:

The air fuel ratio sensor has an output delay of a few seconds and the heated oxygen sensor has a maximum output delay of approximately 20 seconds.


Case Air Fuel Ratio Sensor (Sensor 1) Output Voltage Heated Oxygen Sensor (Sensor 2) Output Voltage Main Suspected Trouble Area
1
A373788E05
0.135,0.302 1.719,0.76 1.583,0.458 10 false Injection Volume 1.375,0.75 2.26,1.083 0.885,0.333 10 false 12.5% 1.333,1.167 2.219,1.5 0.885,0.333 10 false -12.5%

A373791E01
2.896,0.969 3.427,1.25 0.531,0.281 10 false OK 0.948,1.167 2.021,1.5 1.073,0.333 10 false Below 3.1 V 0.625,0.792 2.115,1.167 1.49,0.375 10 false Higher than 3.4 V 0.156,0.24 1.438,0.635 1.281,0.396 10 false Output Voltage

A373788E05
0.135,0.302 1.719,0.76 1.583,0.458 10 false Injection Volume 1.375,0.75 2.26,1.083 0.885,0.333 10 false 12.5% 1.333,1.167 2.219,1.5 0.885,0.333 10 false -12.5%

A373789E01
0.583,0.76 2.042,1.198 1.458,0.438 10 false Higher than 0.55 V 0.969,1.135 1.938,1.448 0.969,0.313 10 false Below 0.4 V 0.208,0.271 1.635,0.677 1.427,0.406 10 false Output Voltage 2.896,0.948 3.427,1.26 0.531,0.313 10 false OK

-
2
A373788E05
0.135,0.302 1.719,0.76 1.583,0.458 10 false Injection Volume 1.375,0.75 2.26,1.083 0.885,0.333 10 false 12.5% 1.333,1.167 2.219,1.5 0.885,0.333 10 false -12.5%

A373790E01
2.875,1.052 3.427,1.333 0.552,0.281 10 false NG 0.51,1.156 1.823,1.521 1.313,0.365 10 false Almost no reaction 0.354,0.469 1.49,0.906 1.135,0.438 10 false Output Voltage

A373788E05
0.135,0.302 1.719,0.76 1.583,0.458 10 false Injection Volume 1.375,0.75 2.26,1.083 0.885,0.333 10 false 12.5% 1.333,1.167 2.219,1.5 0.885,0.333 10 false -12.5%

A373789E01
0.583,0.76 2.042,1.198 1.458,0.438 10 false Higher than 0.55 V 0.969,1.135 1.938,1.448 0.969,0.313 10 false Below 0.4 V 0.208,0.271 1.635,0.677 1.427,0.406 10 false Output Voltage 2.896,0.948 3.427,1.26 0.531,0.313 10 false OK

·

Air fuel ratio sensor

·

Air fuel ratio sensor heater

·

Air fuel ratio sensor circuit


3
A373788E05
0.135,0.302 1.719,0.76 1.583,0.458 10 false Injection Volume 1.375,0.75 2.26,1.083 0.885,0.333 10 false 12.5% 1.333,1.167 2.219,1.5 0.885,0.333 10 false -12.5%

A373791E01
2.896,0.969 3.427,1.25 0.531,0.281 10 false OK 0.948,1.167 2.021,1.5 1.073,0.333 10 false Below 3.1 V 0.625,0.792 2.115,1.167 1.49,0.375 10 false Higher than 3.4 V 0.156,0.24 1.438,0.635 1.281,0.396 10 false Output Voltage

A373788E05
0.135,0.302 1.719,0.76 1.583,0.458 10 false Injection Volume 1.375,0.75 2.26,1.083 0.885,0.333 10 false 12.5% 1.333,1.167 2.219,1.5 0.885,0.333 10 false -12.5%

A373790E01
2.875,1.052 3.427,1.333 0.552,0.281 10 false NG 0.51,1.156 1.823,1.521 1.313,0.365 10 false Almost no reaction 0.354,0.469 1.49,0.906 1.135,0.438 10 false Output Voltage

·

Heated oxygen sensor

·

Heated oxygen sensor heater

·

Heated oxygen sensor circuit


4
A373788E05
0.135,0.302 1.719,0.76 1.583,0.458 10 false Injection Volume 1.375,0.75 2.26,1.083 0.885,0.333 10 false 12.5% 1.333,1.167 2.219,1.5 0.885,0.333 10 false -12.5%

A373790E01
2.875,1.052 3.427,1.333 0.552,0.281 10 false NG 0.51,1.156 1.823,1.521 1.313,0.365 10 false Almost no reaction 0.354,0.469 1.49,0.906 1.135,0.438 10 false Output Voltage

A373788E05
0.135,0.302 1.719,0.76 1.583,0.458 10 false Injection Volume 1.375,0.75 2.26,1.083 0.885,0.333 10 false 12.5% 1.333,1.167 2.219,1.5 0.885,0.333 10 false -12.5%

A373790E01
2.875,1.052 3.427,1.333 0.552,0.281 10 false NG 0.51,1.156 1.823,1.521 1.313,0.365 10 false Almost no reaction 0.354,0.469 1.49,0.906 1.135,0.438 10 false Output Voltage

·

Fuel injector assembly

·

Fuel pressure

·

Gas leak from exhaust system (Air fuel ratio extremely rich or lean)



·

Following the Control the Injection Volume for A/F Sensor procedure enables technicians to check and graph the voltage outputs of both the air fuel ratio and heated oxygen sensors.

·

To display the graph, enter the following menus: Powertrain / Engine / Active Test / Control the Injection Volume for A/F Sensor / All Data / AFS Voltage B1S1 and O2S B1S2 or AFS Voltage B2S1 and O2S B2S2; then press the view button.


NOTICE:

Inspect the fuses for circuits related to this system before performing the following inspection procedure.


HINT:
·

Read freeze frame data using the intelligent tester. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.

·

Bank 1 refers to the bank that includes the No. 1 cylinder*.

*: The No. 1 cylinder is the cylinder which is farthest from the transaxle.

·

Bank 2 refers to the bank that does not include the No. 1 cylinder.

·

Sensor 1 refers to the sensor closest to the engine assembly.

·

Sensor 2 refers to the sensor farthest away from the engine assembly.



PROCEDURE

1.READ OUTPUT DTC (DTC P0136, P0137, P0138, P0156, P0157 OR P0158)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the engine switch on (IG).


c.

Turn the tester on.


d.

Enter the following menus: Powertrain / Engine / DTC.


e.

Read the DTCs.

Result
Result Proceed to
DTC P0138 or P0158 is output A
DTC P0137 or P0157 is output B
DTC P0136 or P0156 is output C
DTC P0136, P0137, P0138, P0156, P0157 or P0158 and other DTCs are output D

HINT:

If any DTCs other than P0136, P0137, P0138, P0156, P0157 and P0158 are output, troubleshoot those DTCs first.




A

2.READ VALUE USING INTELLIGENT TESTER (OUTPUT VOLTAGE OF HEATED OXYGEN SENSOR)

B

9.CHECK FOR EXHAUST GAS LEAK

C

7.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (CONTROL THE INJECTION VOLUME FOR A/F SENSOR)

D

2.READ VALUE USING INTELLIGENT TESTER (OUTPUT VOLTAGE OF HEATED OXYGEN SENSOR)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the engine switch on (IG).


c.

Turn the tester on.


d.

Enter the following menus: Powertrain / Engine / Data List / All Data / O2S B1S2 or O2S B2S2.


e.

Allow the engine to idle.


f.

Read the heated oxygen sensor output voltage while idling.

Result
Heated Oxygen Sensor Output Voltage Proceed to
1.0 V or higher A
Less than 1.0 V B



A

3.INSPECT HEATED OXYGEN SENSOR (CHECK FOR SHORT)

B

5.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (CONTROL THE INJECTION VOLUME FOR A/F SENSOR)
3.INSPECT HEATED OXYGEN SENSOR (CHECK FOR SHORT)
a.

Disconnect the heated oxygen sensor connector.

A258655E04
1.573,0.573 1.885,0.885 false 1.573,1.458 1.917,1.26 false 2.521,1.458 2.208,1.26 false 4.76,0.49 5.073,0.802 false 4.76,1.469 5.094,1.271 false 5.833,1.469 5.51,1.271 false 1.385,0.427 1.594,0.594 0.208,0.167 10 false +B 1.385,1.458 1.594,1.625 0.208,0.167 10 false E2 2.521,1.458 2.917,1.625 0.396,0.167 10 false OX1B 0.198,0.094 1.302,0.271 1.104,0.177 10 false Component Side 1.823,0.302 2.438,0.51 0.615,0.208 10 false Bank 1 4.573,0.344 4.781,0.51 0.208,0.167 10 false +B 4.573,1.469 4.781,1.635 0.208,0.167 10 false E2 5.833,1.469 6.229,1.635 0.396,0.167 10 false OX2B 5.042,0.313 5.615,0.5 0.573,0.188 10 false Bank 2 1.344,0.042 2.844,0.229 1.5,0.188 10 false Heated Oxygen Sensor


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
1 (+B) - 3 (E2) Always 10 kΩ or higher
1 (+B) - 4 (OX1B) Always 10 kΩ or higher
2 (+B) - 4 (E2) Always 10 kΩ or higher
2 (+B) - 3 (OX2B) Always 10 kΩ or higher




OK

4.CHECK HARNESS AND CONNECTOR (CHECK FOR SHORT)

NG

REPLACE HEATED OXYGEN SENSOR

4.CHECK HARNESS AND CONNECTOR (CHECK FOR SHORT)
a.

Turn the engine switch to off and wait for 5 minutes or more.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
D1-48 (HT1B) - D1-88 (OX1B) Always 10 kΩ or higher
D1-47 (HT2B) - D1-87 (OX2B) Always 10 kΩ or higher




OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (CONTROL THE INJECTION VOLUME FOR A/F SENSOR)
a.

Connect the intelligent tester to the DLC3.


b.

Start the engine.


c.

Turn the tester on.


d.

Warm up the engine.


e.

Enter the following menus: Powertrain / Engine / Active Test / Control the Injection Volume for A/F Sensor / All Data / AFS Voltage B1S1 and O2S B1S2 or AFS Voltage B2S1 and O2S B2S2.


f.

Change the fuel injection volume using the tester, and monitor the voltage output of the air fuel ratio sensor and heated oxygen sensor displayed on the tester.

HINT:
·

The Control the Injection Volume for A/F Sensor operation lowers the fuel injection volume by 12.5% or increases the injection volume by 12.5%.

·

The air fuel ratio sensor is displayed as AFS Voltage B1S1 or AFS Voltage B2S1, and the heated oxygen sensor is displayed as O2S B1S2 or O2S B2S2, on the tester.

·

The air fuel ratio sensor has an output delay of a few seconds and the heated oxygen sensor has a maximum output delay of approximately 20 seconds.

·

If the sensor output voltage does not change (almost no reaction) while performing the Active Test, the sensor may be malfunctioning.



Result
Tester Display
(Sensor)
Voltage Variation Proceed to
AFS Voltage B1S1
AFS Voltage B2S1
(Air fuel ratio)
Alternates between higher and less than 3.3 V OK
Remains at higher than 3.3 V NG
Remains at less than 3.3 V NG

HINT:

A normal heated oxygen sensor voltage (O2S B1S2 or O2S B2S2) reacts in accordance with increases and decreases in fuel injection volumes. When the air fuel ratio sensor voltage (AFS Voltage B1S1 or AFS Voltage B2S1) remains at either less or higher than 3.3 V despite the heated oxygen sensor indicating a normal reaction, the air fuel ratio sensor is malfunctioning.


A121606E78
5.885,2.479 6.365,1.396 false 5.552,2.271 6.365,1.396 false 5.708,1.667 6.365,1.396 false 5.563,2.448 5.844,2.667 false 3.021,1.26 2.865,1.677 false 4.333,1.813 4.094,1.688 false 3.573,2.604 3.188,2.917 false 1.958,1.99 2.125,1.99 false 1.958,2.948 2.156,2.948 false 1.531,1.896 1.906,2.052 0.375,0.156 10 false 3.3 V 2.667,0.26 3.083,0.458 0.417,0.198 10 false 12.5% 4.125,1.125 4.781,1.323 0.656,0.198 10 false -12.5% 1.656,2.854 1.906,3.052 0.25,0.198 10 false 1 V 1.667,3.385 1.906,3.583 0.24,0.198 10 false 0 V 3.073,1.146 4,1.344 0.927,0.198 10 false Malfunctioning 5.854,2.615 6.792,2.781 0.938,0.167 10 false Malfunctioning 4.76,0.125 5.823,0.323 1.063,0.198 10 false Injection Volume 3.635,2.51 5.563,2.729 1.927,0.219 10 false Heated Oxygen Sensor Output 6.406,1.125 6.938,1.813 0.531,0.688 10 false Air Fuel Ratio Sensor Output 4.406,1.75 4.906,1.948 0.5,0.198 10 false Normal



OK

6.INSPECT AIR FUEL RATIO SENSOR

NG

15.REPLACE AIR FUEL RATIO SENSOR
6.INSPECT AIR FUEL RATIO SENSOR
HINT:

This air fuel ratio sensor test is to check the air fuel ratio sensor current during the fuel-cut operation. When the sensor is normal, the sensor current will indicate less than 2.2 mA in this test.


a.

Connect the intelligent tester to the DLC3.


b.

Start the engine.


c.

Turn the tester on.



e.

Drive the vehicle by the driving pattern as listed below:

CAUTION:

When performing the confirmation driving pattern, obey all speed limits and traffic laws.


i.

Warm up the engine until the engine coolant temperature reaches 75°C (167°F) or higher.


ii.

Drive the vehicle at 60 km/h (37 mph) or more for 10 minutes or more.


iii.

Stop the vehicle.


iv.

Accelerate the vehicle to 60 km/h (37 mph) or more and decelerate for 5 seconds or more. Perform this 3 times.

A152792E24
1.357,2.513 2.638,2.697 1.281,0.184 10 10 minutes or more 2.973,2.513 4.186,2.697 1.213,0.184 10 5 seconds or more 4.271,2.513 5.468,2.697 1.197,0.184 10 5 seconds or more 5.56,2.513 6.739,2.697 1.179,0.184 10 5 seconds or more 0.152,0.078 1.451,0.293 1.299,0.215 12 Driving Pattern: 0.348,1.224 1.006,1.602 0.658,0.378 10 60 km/h 0.348,2.055 0.884,2.415 0.536,0.360 10 0 km/h



f.

Enter the following menus: Powertrain / Engine / Data List / All Data / AFS Current B1S1 and AFS Current B2S1.


g.

Read the value of the air fuel ratio sensor current while the fuel-cut operation is being performed.

Standard current:

Less than 2.2 mA


HINT:
·

To measure the air fuel ratio sensor current precisely, perform the fuel-cut operation as long as possible.

·

If it is difficult to measure the air fuel ratio sensor current, use the snapshot function of the tester.





OK

12.REPLACE HEATED OXYGEN SENSOR

NG

15.REPLACE AIR FUEL RATIO SENSOR
7.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (CONTROL THE INJECTION VOLUME FOR A/F SENSOR)
a.

Connect the intelligent tester to the DLC3.


b.

Start the engine.


c.

Turn the tester on.


d.

Warm up the engine.


e.

Enter the following menus: Powertrain / Engine / Active Test / Control the Injection Volume for A/F Sensor / All Data / O2S B1S2 or O2S B2S2.


f.

Change the fuel injection volume using the tester, monitoring the voltage output of the heated oxygen sensors displayed on the tester.

HINT:
·

The Control the Injection Volume for A/F Sensor operation lowers the fuel injection volume by 12.5% or increases the injection volume by 12.5%.

·

The heated oxygen sensor has a maximum output delay of approximately 20 seconds.



Standard Voltage:

Fluctuates between 0.4 V or less and 0.55 V or higher.




OK

8.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (CONTROL THE INJECTION VOLUME FOR A/F SENSOR)

NG

9.CHECK FOR EXHAUST GAS LEAK
8.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (CONTROL THE INJECTION VOLUME FOR A/F SENSOR)
a.

Connect the intelligent tester to the DLC3.


b.

Start the engine.


c.

Turn the tester on.


d.

Warm up the engine.


e.

Enter the following menus: Powertrain / Engine / Active Test / Control the Injection Volume for A/F Sensor / All Data / AFS Voltage B1S1 and O2S B1S2 or AFS Voltage B2S1 and O2S B2S2.


f.

Change the fuel injection volume using the tester, and monitor the voltage output of air fuel ratio and heated oxygen sensors displayed on the tester.

HINT:
·

The Control the Injection Volume for A/F Sensor operation lowers the fuel injection volume by 12.5% or increases the injection volume by 12.5%.

·

The air fuel ratio sensor is displayed as AFS Voltage B1S1 or AFS Voltage B2S1, and the heated oxygen sensor is displayed as O2S B1S2 or O2S B2S2, on the tester.

·

The air fuel ratio sensor has an output delay of a few seconds and the heated oxygen sensor has a maximum output delay of approximately 20 seconds.

·

If the sensor output voltage does not change (almost no reaction) while performing the Active Test, the sensor may be malfunctioning.



Result
Tester Display (Sensor) Voltage Variation Proceed to
AFS Voltage B1S1
AFS Voltage B2S1
(Air fuel ratio)
Alternates between higher and less than 3.3 V OK
Remains at higher than 3.3 V NG
Remains at less than 3.3 V NG

HINT:

A normal heated oxygen sensor voltage (O2S B1S2 or O2S B2S2) reacts in accordance with increases and decreases in fuel injection volumes. When the air fuel ratio sensor voltage (AFS Voltage B1S1 or AFS Voltage B2S1) remains at either less or higher than 3.3 V despite the heated oxygen sensor indicating a normal reaction, the air fuel ratio sensor is malfunctioning.


A121606E78
5.885,2.479 6.365,1.396 false 5.552,2.271 6.365,1.396 false 5.708,1.667 6.365,1.396 false 5.563,2.448 5.844,2.667 false 3.021,1.26 2.865,1.677 false 4.333,1.813 4.094,1.688 false 3.573,2.604 3.188,2.917 false 1.958,1.99 2.125,1.99 false 1.958,2.948 2.156,2.948 false 1.531,1.896 1.906,2.052 0.375,0.156 10 false 3.3 V 2.667,0.26 3.083,0.458 0.417,0.198 10 false 12.5% 4.125,1.125 4.781,1.323 0.656,0.198 10 false -12.5% 1.656,2.854 1.906,3.052 0.25,0.198 10 false 1 V 1.667,3.385 1.906,3.583 0.24,0.198 10 false 0 V 3.073,1.146 4,1.344 0.927,0.198 10 false Malfunctioning 5.854,2.615 6.792,2.781 0.938,0.167 10 false Malfunctioning 4.76,0.125 5.823,0.323 1.063,0.198 10 false Injection Volume 3.635,2.51 5.563,2.729 1.927,0.219 10 false Heated Oxygen Sensor Output 6.406,1.125 6.938,1.813 0.531,0.688 10 false Air Fuel Ratio Sensor Output 4.406,1.75 4.906,1.948 0.5,0.198 10 false Normal



OK

CHECK ENGINE TO DETERMINE CAUSE OF EXTREMELY RICH OR LEAN ACTUAL AIR FUEL RATIO (FUEL INJECTOR ASSEMBLY, FUEL SYSTEM, INTAKE SYSTEM, ETC.)

NG

15.REPLACE AIR FUEL RATIO SENSOR
9.CHECK FOR EXHAUST GAS LEAK
a.

Check for exhaust gas leaks.

OK:

No gas leaks.




OK

10.INSPECT HEATED OXYGEN SENSOR (HEATER RESISTANCE)

NG

REPAIR OR REPLACE EXHAUST GAS LEAK POINT

10.INSPECT HEATED OXYGEN SENSOR (HEATER RESISTANCE)

OK

11.CHECK HARNESS AND CONNECTOR (HEATED OXYGEN SENSOR - ECM)

NG

11.CHECK HARNESS AND CONNECTOR (HEATED OXYGEN SENSOR - ECM)
a.

Disconnect the heated oxygen sensor connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for open):
Tester Connection Condition Specified Condition
G53-2 (HT1B) - D1-48 (HT1B) Always Below 1 Ω
G53-4 (OX1B) - D1-88 (OX1B) Always Below 1 Ω
G53-3 (E2) - D1-65 (EX1B) Always Below 1 Ω
D39-1 (HT2B) - D1-47 (HT2B) Always Below 1 Ω
D39-3 (OX2B) - D1-87 (OX2B) Always Below 1 Ω
D39-4 (E2) - D1-64 (EX2B) Always Below 1 Ω


Standard Resistance (Check for short):
Tester Connection Condition Specified Condition
G53-2 (HT1B) or D1-48 (HT1B) - Body ground Always 10 kΩ or higher
G53-4 (OX1B) or D1-88 (OX1B) - Body ground Always 10 kΩ or higher
D39-1 (HT2B) or D1-47 (HT2B) - Body ground Always 10 kΩ or higher
D39-3 (OX2B) or D1-87 (OX2B) - Body ground Always 10 kΩ or higher




OK

12.REPLACE HEATED OXYGEN SENSOR

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

12.REPLACE HEATED OXYGEN SENSOR
a.


NEXT

13.PERFORM CONFIRMATION DRIVING PATTERN
13.PERFORM CONFIRMATION DRIVING PATTERN
a.

Perform Confirmation Driving Pattern.



NEXT

14.CHECK WHETHER DTC OUTPUT RECURS (DTC P0136, P0137, P0138, P0156, P0157 OR P0158)
14.CHECK WHETHER DTC OUTPUT RECURS (DTC P0136, P0137, P0138, P0156, P0157 OR P0158)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the engine switch on (IG).


c.

Turn the tester on.


d.

Enter the following menus: Powertrain / Engine / Utility / All Readiness.


e.

Input the DTC: P0136, P0137, P0138, P0156, P0157 or P0158.


f.

Check that the DTC monitor is NORMAL. If the DTC monitor is INCOMPLETE, perform the driving pattern again but increase the vehicle speed.

Result
Result Proceed to
ABNORMAL
(DTC P0136, P0137, P0138, P0156, P0157 or P0158 is output)
A
NORMAL
(DTC is not output)
B



A

B

END

15.REPLACE AIR FUEL RATIO SENSOR
a.


NEXT

16.PERFORM CONFIRMATION DRIVING PATTERN
16.PERFORM CONFIRMATION DRIVING PATTERN
a.

Perform Confirmation Driving Pattern.



NEXT

17.CHECK WHETHER DTC OUTPUT RECURS (DTC P0136, P0138, P0156 OR P0158)
17.CHECK WHETHER DTC OUTPUT RECURS (DTC P0136, P0138, P0156 OR P0158)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the engine switch on (IG).


c.

Turn the tester on.


d.

Enter the following menus: Powertrain / Engine / Utility / All Readiness.


e.

Input the DTC: P0136, P0138, P0156 or P0158.


f.

Check that the DTC monitor is NORMAL. If the DTC monitor is INCOMPLETE, perform the driving pattern again but increase the vehicle speed.


Result
Result Proceed to
ABNORMAL
(DTC P0136, P0138, P0156 or P0158 is output)
A
NORMAL
(DTC is not output)
B


A

B

END