Home › Engine / Hybrid System › 2GR-FE ENGINE CONTROL › SFI SYSTEM
RM24M0E _51 Engine / Hybrid System _059540 2GR-FE ENGINE CONTROL _0291770 SFI SYSTEM C

2GR-FE ENGINE CONTROL  SFI SYSTEM  P0037  Oxygen Sensor Heater Control Circuit Low (Bank 1 Sensor 2)  P0038  Oxygen Sensor Heater Control Circuit High (Bank 1 Sensor 2)  P0057  Oxygen Sensor Heater Control Circuit Low (Bank 2 Sensor 2)  P0058  Oxygen Sensor Heater Control Circuit High (Bank 2 Sensor 2)  P102D  O2 Sensor Heater Circuit Performance Bank 1 Sensor 2 Stuck ON  P105D  O2 Sensor Heater Circuit Performance Bank 2 Sensor 2 Stuck ON  


DESCRIPTION

In order to obtain a high purification rate of the carbon monoxide (CO), hydrocarbon (HC) and nitrogen oxide (NOx) components in the exhaust gas, a TWC (Three-Way Catalytic Converter) is used. For the most efficient use of the TWC, the air fuel ratio must be precisely controlled so that it is always close to the stoichiometric air fuel level. For the purpose of helping the ECM to deliver accurate air fuel ratio control, a heated oxygen sensor is used.

The heated oxygen sensor is located behind the TWC, and detects the oxygen concentration in the exhaust gas. Since the sensor is integrated with the heater that heats the sensing portion, it is possible to detect the oxygen concentration even when the intake air volume is low (the exhaust gas temperature is low).

When the air fuel ratio becomes lean, the oxygen concentration in the exhaust gas is high. The heated oxygen sensor informs the ECM that the post-TWC air fuel ratio is lean (low voltage, i.e. less than 0.45 V).

Conversely, when the air fuel ratio is richer than the stoichiometric air fuel level, the oxygen concentration in the exhaust gas is low. The heated oxygen sensor informs the ECM that the post-TWC air fuel ratio is rich (high voltage, i.e. higher than 0.45 V). The heated oxygen sensor has the property of changing its output voltage drastically when the air fuel ratio is close to the stoichiometric level.

The ECM uses the supplementary information from the heated oxygen sensor to determine whether the air fuel ratio after the TWC is rich or lean, and adjusts the fuel injection duration accordingly. Thus, if the heated oxygen sensor is working improperly due to internal malfunctions, the ECM is unable to compensate for deviations in the primary air fuel ratio control.

A203088E18
2.656,1.458 3.292,1.229 3.292,1.229 2.781,1.521 false 2.927,1.313 3.24,1 false 2.698,1.635 3.281,1.635 false 2.604,2.24 3.26,2.208 false 2.698,2.427 3.271,2.563 false 1.198,2.865 1.427,2.865 false 1.521,0.823 2.531,1.021 1.01,0.198 10 false Atmospheric Air 3.271,0.906 4.01,1.104 0.74,0.198 10 false Housing 3.344,1.135 4.875,1.333 1.531,0.198 10 false Platinum Electrode 4.063,0.906 5.031,1.104 0.969,0.198 10 false Output Voltage 4.969,0.677 6.385,0.927 1.417,0.25 10 false Ideal Air Fuel Mixture 2.031,3.125 2.927,3.323 0.896,0.198 10 false Exhaust Gas 3.323,1.542 4.594,1.969 1.271,0.427 10 false Solid Electrolyte (Zirconia Element) 3.292,2.479 4.49,2.677 1.198,0.198 10 false Coating (Ceramic) 3.344,2.104 3.823,2.302 0.479,0.198 10 false Heater 1.479,2.771 1.917,2.979 0.438,0.208 10 false Cover 4.656,2.844 6.635,3.104 1.979,0.26 10 false Richer - Air Fuel Ratio - Leaner

HINT:

When any of these DTCs is stored, the ECM enters fail-safe mode. The ECM turns off the heated oxygen sensor heater in fail-safe mode. Fail-safe mode continues until the engine switch is turned off.

A140671E10
0.075,0.034 3.358,0.223 3.283,0.188 10 Reference (System Diagram of Bank 1 Sensor 2): 1.278,0.878 1.511,1.059 0.233,0.181 10 EFI 2.099,0.632 2.746,0.813 0.647,0.181 10 EFI MAIN 3.377,0.386 4.957,0.568 1.580,0.181 10 Heated Oxygen Sensor 3.457,1.017 3.647,1.198 0.191,0.181 10 +B 4.55,1.024 4.930,1.205 0.380,0.181 10 HT1B 3.457,1.588 3.685,1.769 0.229,0.181 10 E2 4.55,1.595 4.977,1.776 0.427,0.181 10 OX1B 3.885,0.842 4.320,1.023 0.436,0.181 10 Heater 3.871,1.432 4.330,1.614 0.459,0.181 10 Sensor 5.874,0.365 6.200,0.547 0.326,0.181 10 ECM 5.138,1.024 5.518,1.205 0.380,0.181 10 HT1B 5.138,1.595 5.539,1.776 0.401,0.181 10 OX1B 5.138,2.166 5.527,2.347 0.389,0.181 10 EX1B 5.138,2.733 5.541,2.914 0.403,0.181 10 MREL 0.494,1.043 0.985,1.403 0.492,0.360 10 from Battery


DTC No. DTC Detection Condition Trouble Area
P0037
P0057
Heated oxygen sensor heater current is the specified value or less while the heater is operating (1 trip detection logic).
·

Open in heated oxygen sensor (bank 1, 2 sensor 2) heater circuit

·

Heated oxygen sensor (bank 1, 2 sensor 2)

·

ECM


P0038
P0058
Heated oxygen sensor heater current reaches high limit
(1 trip detection logic).
·

Short in heated oxygen sensor (bank 1, 2 sensor 2) heater circuit

·

Heated oxygen sensor (bank 1, 2 sensor 2)

·

ECM


P102D
P105D
Heated oxygen sensor heater current is higher than the specified value while the heater is not operating (1 trip detection logic). ECM

WIRING DIAGRAM

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following inspection procedure.


HINT:
·

Bank 1 refers to the bank that includes the No. 1 cylinder*.

*: The No. 1 cylinder is the cylinder which is farthest from the transaxle.

·

Bank 2 refers to the bank that does not include the No. 1 cylinder.

·

Sensor 1 refers to the sensor closest to the engine assembly.

·

Sensor 2 refers to the sensor farthest away from the engine assembly.

·

Read freeze frame data using the intelligent tester. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can be helpful in determining whether the vehicle was running or stopped, whether the engine was warmed up or not, whether the air-fuel ratio was lean or rich, as well as other data recorded at the time of a malfunction.

·

Change the fuel injection volume using the Control the Injection Volume for A/F Sensor function provided in the Active Test and monitor the heated oxygen sensor output voltage (See page Engine / Hybrid System>2GR-FE ENGINE CONTROL>SFI SYSTEM>P0136). If the sensor output voltage does not change (almost no reaction) while performing the Active Test, the sensor may be malfunctioning.



PROCEDURE

1.INSPECT HEATED OXYGEN SENSOR (HEATER RESISTANCE)

OK

2.CHECK TERMINAL VOLTAGE (+B OF HEATED OXYGEN SENSOR)

NG

2.CHECK TERMINAL VOLTAGE (+B OF HEATED OXYGEN SENSOR)
a.
U188427E01
0.145,0.137 1.440,0.284 1.295,0.147 10 Wire Harness Side: 0.368,0.676 2.538,0.813 2.170,0.137 10 Heated Oxygen Sensor Connector 2.293,1.793 2.995,1.930 0.702,0.137 10 Front View 2.293,3.426 2.995,3.563 0.702,0.137 10 Front View 0.723,1.73 1.004,1.872 0.281,0.142 10 G53 0.628,2.016 1.091,2.158 0.463,0.142 10 Bank 1 0.723,3.128 1.004,3.270 0.281,0.142 10 D39 0.628,3.414 1.091,3.556 0.463,0.142 10 Bank 2 2.263,1.483 2.470,1.621 0.207,0.137 10 +B 1.875,1.815 2.237,1.564 false 2.263,3.082 2.470,3.219 0.207,0.137 10 +B 2.022,3.312 2.237,3.162 false

Disconnect the heated oxygen sensor connector.


b.

Turn the engine switch on (IG).


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
G53-1 (+B) - Body ground Engine switch on (IG) 11 to 14 V
D39-2 (+B) - Body ground Engine switch on (IG) 11 to 14 V




OK

3.CHECK HARNESS AND CONNECTOR (HEATED OXYGEN SENSOR - ECM)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (HEATED OXYGEN SENSOR - EFI MAIN RELAY)

3.CHECK HARNESS AND CONNECTOR (HEATED OXYGEN SENSOR - ECM)
a.

Disconnect the heated oxygen sensor connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for open):
Terminal Connection Condition Specified Condition
G53-2 (HT1B) - D1-48 (HT1B) Always Below 1 Ω
D39-1 (HT2B) - D1-47 (HT2B) Always Below 1 Ω


Standard Resistance (Check for short):
Terminal Connection Condition Specified Condition
G53-2 (HT1B) or D1-48 (HT1B) - Body ground Always 10 kΩ or higher
D39-1 (HT2B) or D1-47 (HT2B) - Body ground Always 10 kΩ or higher




OK

4.CHECK WHETHER DTC OUTPUT RECURS (DTC P0037, P0038, P0057, P0058, P102D or P105D)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK WHETHER DTC OUTPUT RECURS (DTC P0037, P0038, P0057, P0058, P102D or P105D)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the engine switch on (IG).


c.

Turn the tester on.



e.

Turn the engine switch off and wait for at least 30 seconds.


f.

Start the engine.


g.

Allow the engine to idle for 2 minutes.


h.

Enter the following menus: Powertrain / Engine / DTC.


i.

Read the DTCs.

Result
Result Proceed to
DTC is not output A
DTC P0037, P0038, P0057, P0058, P102D or P105D is output B



A

B