Home › Engine / Hybrid System › 2GR-FE ENGINE CONTROL › SFI SYSTEM
RM24M0E _51 Engine / Hybrid System _059540 2GR-FE ENGINE CONTROL _0291770 SFI SYSTEM C

2GR-FE ENGINE CONTROL  SFI SYSTEM  P0100  Mass or Volume Air Flow Circuit  P0102  Mass or Volume Air Flow Circuit Low Input  P0103  Mass or Volume Air Flow Circuit High Input  


DESCRIPTION

The mass air flow meter sub-assembly is a sensor that measures the amount of air flowing through the throttle valve.

The ECM uses this information to determine fuel injection duration and to provide an appropriate air fuel ratio.

Inside the mass air flow meter sub-assembly, there is a heated platinum wire which is exposed to the flow of intake air.

By applying a specific electrical current to the wire, the ECM heats it to a specific temperature. The flow of incoming air cools both the wire and an internal thermistor, affecting their resistance. To maintain a constant current value, the ECM varies the voltage applied to the wire and internal thermistor. The voltage level is proportional to the airflow through the sensor, and the ECM uses it to calculate the intake air volume.

The circuit is constructed so that the platinum hot wire and the temperature sensor create a bridge circuit, and the power transistor is controlled so that the potentials of A and B remain equal to maintain the predetermined temperature.

HINT:

When any of these DTCs is stored, the ECM enters fail-safe mode. During fail-safe mode, the ignition timing is calculated by the ECM, according to the engine speed and throttle valve position. Fail-safe mode continues until a pass condition is detected.


A165052E36
1.906,1.49 1.573,0.323 1.573,0.323 1.427,0.323 false 2.271,1.49 2.406,1.063 2.406,1.063 2.563,1.063 false 4.823,1.333 4.396,1.917 4.396,1.917 4.396,2.188 false 5.115,1.563 5.563,1.906 5.563,1.906 5.563,2.167 false 5.115,2.198 7.156,2.438 2.042,0.24 10 false Temperature Sensor (Thermistor) 2.25,0.198 2.531,0.417 0.281,0.219 10 false +B 2.24,0.552 3.604,0.792 1.365,0.24 10 false Power Transistor 3.313,2.208 5.417,2.406 2.104,0.198 10 false Platinum Hot Wire (Heater) 1.656,1.49 1.823,1.698 0.167,0.208 10 false A 2.469,1.479 2.656,1.677 0.188,0.198 10 false B 2.885,1.583 4.083,1.781 1.198,0.198 10 false Output Voltage 2.604,0.979 4.406,1.177 1.802,0.198 10 false Platinum Hot Wire (Heater) 0.177,0.24 1.469,0.615 1.292,0.375 10 false Temperature Sensor (Thermistor)

DTC No. DTC Detection Condition Trouble Area
P0100 Open or short in mass air flow meter sub-assembly circuit for 3 seconds (1 trip detection logic)
·

Open or short in mass air flow meter sub-assembly circuit

·

Mass air flow meter sub-assembly

·

ECM


P0102 Open in mass air flow meter sub-assembly circuit for 3 seconds (1 trip detection logic)
·

Open in mass air flow meter sub-assembly circuit

·

Mass air flow meter sub-assembly

·

ECM


P0103 Short in mass air flow meter sub-assembly circuit for 3 seconds (1 trip detection logic)
·

Short in mass air flow meter sub-assembly circuit (+B circuit)

·

Mass air flow meter sub-assembly

·

ECM



HINT:

When any of these DTCs are output, check the air flow rate by using the intelligent tester. Enter the following menus: Powertrain / Engine / Data List / MAF.

Mass Air Flow Rate (gm/sec) Malfunctions
Approximately 0.0
·

Open in mass air flow meter sub-assembly power source circuit

·

Open or short in VG circuit


271.0 or more Open in E2G circuit


WIRING DIAGRAM

A159615E03
5.823,0.927 6.031,1.094 0.208,0.167 10 false D1 6.115,0.896 6.438,1.063 0.323,0.167 10 false VG 4.406,0.813 4.729,0.979 0.323,0.167 10 false VG 3.385,0.708 3.708,0.875 0.323,0.167 10 false +B 5.833,0.719 6.156,0.885 0.323,0.167 10 false 72 4.719,1.031 5.042,1.198 0.323,0.167 10 false 5 2.885,2.75 3.208,2.917 0.323,0.167 10 false 5 2.896,2.354 3.219,2.521 0.323,0.167 10 false 1 2.323,2.76 2.646,2.927 0.323,0.167 10 false 3 2.323,2.333 2.646,2.5 0.323,0.167 10 false 2 4.719,1.531 5.042,1.698 0.323,0.167 10 false 4 3.229,0.948 3.552,1.115 0.323,0.167 10 false 3 5.823,1.427 6.021,1.594 0.198,0.167 10 false D1 6.115,1.396 6.438,1.563 0.323,0.167 10 false E2G 4.354,1.323 4.677,1.49 0.323,0.167 10 false E2G 2.917,1.896 5.354,2.083 2.438,0.188 10 false D3 Mass Air Flow Meter Sub-assembly 2.323,2.958 2.969,3.146 0.646,0.188 10 false EFI MAIN 3.875,3.76 4.521,3.906 0.646,0.146 10 false F/B BATT 6.281,5.229 6.635,5.417 0.354,0.188 10 false ECM 2.385,3.76 3.031,3.948 0.646,0.188 10 false FL MAIN 1.156,4.323 1.667,4.51 0.51,0.188 10 false Battery 4.021,2.823 4.292,3.01 0.271,0.188 10 false EFI 5.833,1.219 6.156,1.385 0.323,0.167 10 false 73 5.823,2.26 6.146,2.427 0.323,0.167 10 false A7 6.115,2.229 6.573,2.396 0.458,0.167 10 false MREL 5.833,2.052 6.156,2.219 0.323,0.167 10 false 44

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following inspection procedure.


HINT:

Read freeze frame data using the intelligent tester. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can be helpful in determining whether the vehicle was running or stopped, whether the engine was warmed up or not, whether the air-fuel ratio was lean or rich, as well as other data recorded at the time of a malfunction.


PROCEDURE

1.READ OUTPUT DTC (DTC P0102 OR P0103)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the engine switch on (IG).


c.

Turn the tester on.


d.

Enter the following menus: Powertrain / Engine / DTC.


e.

Read the DTCs.

Result
Result Proceed to
DTC P0102 is output A
DTC P0103 is output B



A

2.CHECK TERMINAL VOLTAGE (+B OF MASS AIR FLOW METER SUB-ASSEMBLY)

B

5.CHECK HARNESS AND CONNECTOR (SENSOR GROUND)
2.CHECK TERMINAL VOLTAGE (+B OF MASS AIR FLOW METER SUB-ASSEMBLY)
a.
U188314E02
0.906,0.615 1.698,1.021 false 0.031,0.052 1.333,0.25 1.302,0.198 10 false Wire Harness Side: 2.469,0.333 3.156,0.531 0.688,0.198 10 false Front View 0.719,1.667 2.76,1.865 2.042,0.198 10 false Mass Air Flow Meter Connector 0.594,0.51 0.823,0.708 0.229,0.198 10 false +B 0.281,1.656 0.479,1.813 0.198,0.156 10 false D3

Disconnect the mass air flow meter sub-assembly connector.


b.

Turn the engine switch on (IG).


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
D3-3 (+B) - Body ground Engine switch on (IG) 11 to 14 V




OK

3.CHECK HARNESS AND CONNECTOR (MASS AIR FLOW METER SUB-ASSEMBLY - ECM)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (EFI MAIN RELAY - MASS AIR FLOW METER SUB-ASSEMBLY)

3.CHECK HARNESS AND CONNECTOR (MASS AIR FLOW METER SUB-ASSEMBLY - ECM)
a.

Disconnect the mass air flow meter sub-assembly connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for open):
Tester Connection Condition Specified Condition
D1-72 (VG) - D3-5 (VG) Always Below 1 Ω
D1-73 (E2G) - D3-4 (E2G) Always Below 1 Ω


Standard Resistance (Check for short):
Tester Connection Condition Specified Condition
D1-72 (VG) or D3-5 (VG) - Body ground Always 10 kΩ or higher




OK

4.INSPECT MASS AIR FLOW METER SUB-ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.INSPECT MASS AIR FLOW METER SUB-ASSEMBLY
a.

Inspect the mass air flow meter sub-assembly, referring to the On-vehicle Inspection for Mass Air Flow Meter (See page Engine / Hybrid System>2GR-FE ENGINE CONTROL>MASS AIR FLOW METER>ON-VEHICLE INSPECTION).


b.

Inspect the mass air flow meter sub-assembly, referring to the Inspection for Mass Air Flow Meter (See page Engine / Hybrid System>2GR-FE ENGINE CONTROL>MASS AIR FLOW METER>INSPECTION).


c.

Inspect the function of the mass air flow meter sub-assembly.

i.

Connect the intelligent tester to the DLC3.


ii.

Turn the engine switch on (IG).


iii.

Turn the tester on.


iv.

Enter the following menus: Powertrain / Engine / Data List / All Data / MAF.


v.

Start the engine.


vi.

Check that the MAF value changes when the engine is raced.

OK:

The reading changes.





OK

NG

REPLACE MASS AIR FLOW METER SUB-ASSEMBLY

5.CHECK HARNESS AND CONNECTOR (SENSOR GROUND)
a.

Disconnect the mass air flow meter sub-assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for open):
Tester Connection Condition Specified Condition
D3-4 (E2G) - Body ground Always Below 1 Ω




OK

REPLACE MASS AIR FLOW METER SUB-ASSEMBLY

NG

6.CHECK HARNESS AND CONNECTOR (MASS AIR FLOW METER SUB-ASSEMBLY - ECM)
6.CHECK HARNESS AND CONNECTOR (MASS AIR FLOW METER SUB-ASSEMBLY - ECM)
a.

Disconnect the mass air flow meter sub-assembly connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for open):
Tester Connection Condition Specified Condition
D1-73 (E2G) - D3-4 (E2G) Always Below 1 Ω




OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR