Home › Engine / Hybrid System › 2GR-FE ENGINE CONTROL › CAMSHAFT OIL CONTROL VALVE › 2013.04–2016.05
RM24M0E _51 Engine / Hybrid System _059540 2GR-FE ENGINE CONTROL _0291781 CAMSHAFT OIL CONTROL VALVE A

2GR-FE ENGINE CONTROL  CAMSHAFT OIL CONTROL VALVE  INSTALLATION  


PROCEDURE

Hide 11101J 1.INSTALL CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY (for Bank 2 Exhaust Side)

a.
U188425E01
0.884,0.641 1.357,0.811 0.473,0.170 10 O-Ring

Apply a light coat of engine oil to the new O-ring and install it to the camshaft timing oil control valve.


b.
A160572

Install the camshaft timing oil control valve assembly with the bolt.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)


c.

Connect the camshaft timing oil control valve assembly connector.


Hide 11101J 2.INSTALL CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY (for Bank 2 Intake Side)

a.
U188424E01
0.842,0.477 1.307,0.633 0.465,0.156 10 O-Ring

Apply a light coat of engine oil to the new O-ring and install it to the camshaft timing oil control valve.


b.
A160573

Install the camshaft timing oil control valve assembly with the bolt.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)


c.

Connect the camshaft timing oil control valve assembly connector.


Hide 11101J 3.INSTALL CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY (for Bank 1 Exhaust Side)

a.
U188424E01
0.842,0.477 1.307,0.633 0.465,0.156 10 O-Ring

Apply a light coat of engine oil to the new O-ring and install it to the camshaft timing oil control valve.


b.
A160575

Install the camshaft timing oil control valve assembly with the bolt.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)


c.

Connect the camshaft timing oil control valve assembly connector.


Hide 11101J 4.INSTALL CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY (for Bank 1 Intake Side)

a.
U188423E01
0.775,0.454 1.241,0.647 0.465,0.193 10 O-Ring

Apply a light coat of engine oil to the new O-ring and install it to the camshaft timing oil control valve.


b.
A160574

Install the camshaft timing oil control valve assembly with the bolt.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)


c.

Connect the camshaft timing oil control valve assembly connector.


Hide 6.INSTALL COWL TOP OUTER PANEL WITH WINDSHIELD WIPER MOTOR AND LINK

a.

Install the cowl top outer panel with windshield wiper motor and link (See page Vehicle Interior>WIPER / WASHER>FRONT WIPER MOTOR>INSTALLATION).


Hide 47202 7.INSTALL BRAKE MASTER CYLINDER RESERVOIR SUB-ASSEMBLY

Hide 55781F 8.INSTALL COWL TOP VENTILATOR LOUVER SUB-ASSEMBLY

Hide 53867H 9.INSTALL FRONT FENDER TO COWL SIDE SEAL LH

Hide 53866J 10.INSTALL FRONT FENDER TO COWL SIDE SEAL RH

Hide 85291B 11.INSTALL FRONT WIPER ARM AND BLADE ASSEMBLY LH

Hide 85291A 12.INSTALL FRONT WIPER ARM AND BLADE ASSEMBLY RH

Hide 16470 14.INSTALL RADIATOR RESERVOIR TANK SUB-ASSEMBLY

Hide 15.CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

Hide 16.INSPECT FOR ENGINE OIL LEAK

a.

Start the engine, and check that there are no oil leaks.


Hide 17.PERFORM INITIALIZATION

a.

Perform initialization (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).

NOTICE:

Certain systems need to be initialized after disconnecting the cable from the negative (-) battery terminal.