Home › Brake › BRAKE › BRAKE MASTER CYLINDER(for LHD) › 2013.04–2016.05
RM24M0E _54 Brake _059558 BRAKE _0291875 BRAKE MASTER CYLINDER(for LHD) A

BRAKE  BRAKE MASTER CYLINDER(for LHD)  INSTALLATION  


PROCEDURE

Hide 47201 1.INSTALL BRAKE MASTER CYLINDER SUB-ASSEMBLY

NOTICE:
·

The master cylinder and piston are designed so that the piston can easily fall out. Prevent this by making sure that the tip of the master cylinder points downward when handling the master cylinder.

·

Make sure foreign matter does not attach to the master cylinder's piston. If foreign matter attaches, clean it off with a cloth. Then apply lithium soap base glycol grease to the entire outer circumference contact surface area of the piston.



a.

Install a new O-ring to the master cylinder.


b.

Install the master cylinder to the booster.


c.
C367438E01
1.906,0.469 2.063,0.667 0.156,0.198 10 false A 2.479,1.458 2.635,1.656 0.156,0.198 10 false B 1.594,1.198 1.75,1.396 0.156,0.198 10 false B

Install the vacuum check valve bracket (labeled A) and tighten the 2 nuts (labeled B).

Torque:
13 N*m (130 kgf*cm, 9 ft.*lbf)


d.
C133368E04
2.469,0.5 2.604,0.656 0.135,0.156 10 false D 2.729,1.281 2.865,1.438 0.135,0.156 10 false C 2.417,0.823 2.552,0.979 0.135,0.156 10 true C

Using SST, connect the 2 brake lines (labeled C) to the master cylinder.

SST
09023-00101  
09023-38201  

Torque:
w/o VSC : 15 N*m (155 kgf*cm, 11 ft.*lbf)

without SST

14 N*m (144 kgf*cm, 10 ft.*lbf)

with SST


Torque:
w/ VSC : 20 N*m (199 kgf*cm, 14 ft.*lbf)

without SST

18 N*m (185 kgf*cm, 13 ft.*lbf)

with SST


HINT:
·

Use a torque wrench with a fulcrum length of 30 cm (11.81 in.).

·

This torque value is effective when SST is parallel to a torque wrench.




e.

Connect the No. 1 reservoir tube (labeled D) to the master cylinder.


Hide 44781D 2.INSTALL RESERVOIR HOSE BRACKET

a.

Install the bracket with the nut.

Torque:
5.4 N*m (55 kgf*cm, 48 in.*lbf)


b.

Install the No. 1 reservoir tube to the clamps of the bracket.


Hide 47202 3.INSTALL BRAKE MASTER CYLINDER RESERVOIR SUB-ASSEMBLY

a.
C367594E01
2.823,0.292 3.135,0.49 0.313,0.198 10 false F 2.865,1.354 3.177,1.552 0.313,0.198 10 false A 2.823,1.885 3.135,2.083 0.313,0.198 10 false H 2.729,2.427 3.042,2.625 0.313,0.198 10 false D 2.865,3.708 3.177,3.906 0.313,0.198 10 false G 2.177,4.469 2.49,4.667 0.313,0.198 10 false C 1.354,4.365 1.667,4.563 0.313,0.198 10 false B 0.125,4.229 0.438,4.427 0.313,0.198 10 false E 0.208,2.563 0.521,2.76 0.313,0.198 10 false E 1.583,2.063 1.896,2.26 0.313,0.198 10 false G

Install the nut (labeled A) to the reservoir.


b.

Install the reservoir to the reservoir bracket (labeled B) with the bolt (labeled C).

Torque:
8.8 N*m (90 kgf*cm, 78 in.*lbf)


c.

Install the reservoir bracket (labeled D) to the reservoir with bracket with the 2 nuts (labeled E).

Torque:
8.8 N*m (90 kgf*cm, 78 in.*lbf)


d.

Connect the No. 1 reservoir tube (labeled F) to the reservoir.


e.

Install the reservoir with brackets to the body with the 2 nuts (labeled G).

Torque:
8.8 N*m (90 kgf*cm, 78 in.*lbf)


f.

Connect the brake fluid level warning switch connector (labeled H) to the reservoir.


Hide 4.BLEED BRAKE SYSTEM

Hide 17700 5.INSTALL AIR CLEANER CASE SUB-ASSEMBLY (for 2AZ-FE)

Hide 17700 6.INSTALL AIR CLEANER CASE SUB-ASSEMBLY (for 2GR-FE)

Hide 17705 7.INSTALL AIR CLEANER CAP SUB-ASSEMBLY (for 2AZ-FE)

Hide 17705 8.INSTALL AIR CLEANER CAP SUB-ASSEMBLY (for 2GR-FE)

Hide 74431 9.INSTALL BATTERY TRAY

Hide 12.CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).