Home › Engine / Hybrid System › 2AZ-FE ENGINE CONTROL › SFI SYSTEM › 2013.04–2014.09
RM24M0E _51 Engine / Hybrid System _059541 2AZ-FE ENGINE CONTROL _0291789 SFI SYSTEM C

2AZ-FE ENGINE CONTROL  SFI SYSTEM  P0016  Crankshaft Position - Camshaft Position Correlation (Bank 1 Sensor A)  


DESCRIPTION

In the VVT (Variable Valve Timing) system, the appropriate intake valve open and close timing is controlled by the ECM. The ECM performs intake valve control by performing the following: 1) controlling the camshaft and camshaft timing oil control valve, and operating the camshaft timing gear assembly; and 2) changing the relative positions of the camshaft and crankshaft.

DTC No. DTC Detection Condition Trouble Area
P0016 Deviation in crankshaft position sensor signal and camshaft position sensor signal (2 trip detection logic).
·

Valve timing

·

Camshaft timing oil control valve

·

Oil control valve filter

·

Camshaft timing gear assembly

·

ECM



MONITOR DESCRIPTION

To monitor the correlation of the intake camshaft position and crankshaft position, the ECM checks the VVT learned value while the engine is idling. The VVT learned value is calibrated based on the camshaft position and crankshaft position. The intake valve timing is set to the most retarded angle while the engine is idling. If the VVT learned value is out of the specified range in consecutive driving cycles, the ECM illuminates the MIL and stores DTC P0016.

CONFIRMATION DRIVING PATTERN

A384166E03
4.302,1.125 4.729,0.469 4.729,0.469 4.938,0.469 false 0.188,0.677 1.156,1 0.969,0.323 10 false Vehicle Speed 0.698,1.76 1.667,2.083 0.969,0.323 10 false Idling 0.177,2.042 1.073,2.448 0.896,0.406 10 false Engine Switch on (IG) 1.521,2.146 2.49,2.469 0.969,0.323 10 false [A] 2.146,1.677 3.115,2 0.969,0.323 10 false [B] 3.167,1.677 4.135,2 0.969,0.323 10 false [C] 4.625,0.906 5.594,1.229 0.969,0.323 10 false [E] 5.698,1.656 6.667,1.979 0.969,0.323 10 false [F] 3.823,3.021 4.792,3.344 0.969,0.323 10 false [D] 6.365,3.042 6.823,3.292 0.458,0.25 10 false [G] 1.875,2.594 2.646,2.969 0.771,0.375 10 false Warming up the engine 2.75,2.604 3.906,2.906 1.156,0.302 10 false 5 minutes or more 4.156,2.625 5.125,2.948 0.969,0.323 10 false 2 to 3 minutes 5,0.333 6.417,0.75 1.417,0.417 10 false There is no designated vehicle speed 5.229,2.625 6.385,2.927 1.156,0.302 10 false 5 minutes or more

1.

Connect the intelligent tester to the DLC3.

2.

Turn the engine switch on (IG) and turn the tester on.

3.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

4.

Turn the engine switch off and wait for at least 30 seconds.

5.

Turn the engine switch on (IG) and turn the tester on [A].

6.

Start the engine and warm it up until the engine coolant temperature reaches 75°C (167°F) or higher [B].

7.

Idle the engine for 5 minutes or more [C].

8.

Enter the following menus: Powertrain / Engine and ECT / DTC [D].

9.

Read the pending DTCs.

HINT:
·

If a pending DTC is output, the system is malfunctioning.

·

If a pending DTC is not output, perform the following procedure.



10.

Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.

11.

Input the DTC: P0016.

12.

Check the DTC judgment result.

Tester Display Description
NORMAL
·

DTC judgment completed

·

System normal


ABNORMAL
·

DTC judgment completed

·

System abnormal


INCOMPLETE
·

DTC judgment not completed

·

Perform driving pattern after confirming DTC enabling conditions


N/A
·

Unable to perform DTC judgment

·

Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit



HINT:
·

If the judgment result shows NORMAL, the system is normal.

·

If the judgment result shows ABNORMAL, the system has a malfunction.

·

If the judgment result shows INCOMPLETE or N/A, perform steps [E] through [G].



13.

Drive the vehicle for 2 to 3 minutes [E].

CAUTION:

When performing the confirmation driving pattern, obey all speed limits and traffic laws.


14.

Idle the engine for 5 minutes or more [F].

15.

Enter the following menus: Powertrain / Engine and ECT / DTC [G].

16.

Read the pending DTCs.

HINT:
·

If a pending DTC is output, the system is malfunctioning.

·

If a pending DTC is not output, perform the following procedure.



17.

Check the DTC judgment result.

HINT:
·

If the judgment result shows NORMAL, the system is normal.

·

If the judgment result shows ABNORMAL, the system has a malfunction.




CAUTION / NOTICE / HINT

HINT:
·

The monitor for this DTC detects when the timing chain is shifted by 2 to 3 teeth or more.

·

Read freeze frame data using the intelligent tester. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.



PROCEDURE

1.CHECK ANY OTHER DTCS OUTPUT (IN ADDITION TO DTC P0016)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the engine switch on (IG).


c.

Turn the tester on.


d.

Enter the following menus: Powertrain / Engine and ECT / DTC.


e.

Read the DTCs.

Result
Result Proceed to
DTC P0016 is output A
DTC P0016 and other DTCs are output B

HINT:

If any DTCs other than P0016 are output, troubleshoot those DTCs first.




A

2.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (CONTROL THE VVT LINEAR)

B

2.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (CONTROL THE VVT LINEAR)
HINT:

If the VVT system can be operated through the Active Test, it can be assumed that the VVT system is operating normally.


a.

Connect the intelligent tester to the DLC3.


b.

Start the engine.


c.

Turn the A/C switch on.


d.

Turn the tester on.


e.

Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the VVT Linear (Bank 1) / All Data / VVT Change Angle #1.


f.

Perform the Active Test. Check that the displacement angle varies.

OK:

Displacement angle varies.




OK

3.ADJUST VALVE TIMING

NG

4.INSPECT CAMSHAFT TIMING OIL CONTROL VALVE
3.ADJUST VALVE TIMING

NEXT

7.CHECK WHETHER DTC OUTPUT RECURS (DTC P0016)
4.INSPECT CAMSHAFT TIMING OIL CONTROL VALVE

OK

5.INSPECT OIL CONTROL VALVE FILTER

NG

REPLACE CAMSHAFT TIMING OIL CONTROL VALVE

5.INSPECT OIL CONTROL VALVE FILTER

OK

6.REPLACE CAMSHAFT TIMING GEAR ASSEMBLY

NG

REPLACE OIL CONTROL VALVE FILTER

6.REPLACE CAMSHAFT TIMING GEAR ASSEMBLY
a.

Replace the camshaft timing gear assembly (See page Engine / Hybrid System>2AZ-FE ENGINE MECHANICAL>ENGINE UNIT>DISASSEMBLY).



NEXT

7.CHECK WHETHER DTC OUTPUT RECURS (DTC P0016)
7.CHECK WHETHER DTC OUTPUT RECURS (DTC P0016)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the engine switch on (IG).


c.

Turn the tester on.



e.

Turn the engine switch off and wait for at least 30 seconds.


f.

Turn the engine switch on (IG).


g.

Turn the tester on.


h.

Start the engine and warm it up.


i.

Drive the vehicle in accordance with the driving pattern described in the Confirmation Driving Pattern.


j.

Enter the following menus: Powertrain / Engine and ECT / DTC / Pending.


k.

Read the pending DTCs.

Result
Result Proceed to
DTC is not output A
DTC is output B



A

END

B