Home › Engine / Hybrid System › 2AZ-FE ENGINE CONTROL › SFI SYSTEM › from 2016.05
RM24M0E _51 Engine / Hybrid System _059541 2AZ-FE ENGINE CONTROL _0291789 SFI SYSTEM C

2AZ-FE ENGINE CONTROL  SFI SYSTEM  P0617  Starter Relay Circuit High  


DESCRIPTION

While the engine is being cranked, battery voltage is applied to terminal STA of the ECM. If the ECM detects the starter control (STA) signal while the vehicle is being driven, it determines that there is a malfunction in the STA circuit. The ECM then illuminates the MIL and stores the DTC.

This monitor runs when the vehicle is driven at 20 km/h (12.43 mph) or more for over 20 seconds.

DTC No. DTC Detection Condition Trouble Area
P0617 When all of the following conditions are met, and a (+B) battery voltage of 10.5 V or higher is applied to the ECM for 20 seconds (1 trip detection logic):

(a) Vehicle speed is more than 20 km/h (12.4 mph)

(b) Engine speed is more than 1000 rpm

(c) STA signal is ON


·

Short in cranking holding function circuit

·

Park/neutral position switch

·

ECM



WIRING DIAGRAM

A235534E07
3.219,6.667 5.865,6.844 2.646,0.177 10 false *1: Continuously Variable Transaxle Model 3.219,7.01 5.156,7.188 1.938,0.177 10 false *2: Automatic Transaxle Model 3.094,4.156 4.896,4.313 1.802,0.156 10 false Park/Neutral Position Switch 3.094,3.99 3.313,4.135 0.219,0.146 10 false D4 4.167,3.75 4.375,3.896 0.208,0.146 10 false 4 2.292,1.313 2.5,1.458 0.208,0.146 10 false 11 2.229,1.49 2.521,1.635 0.292,0.146 10 false G58 2.323,1.656 2.531,1.802 0.208,0.146 10 false 4 3.396,0.719 3.521,0.865 0.125,0.146 10 false 2 3.396,0.385 3.521,0.531 0.125,0.146 10 false 5 4.156,0.719 4.281,0.865 0.125,0.146 10 false 1 4.156,0.385 4.281,0.531 0.125,0.146 10 false 3 4.75,3.385 4.875,3.531 0.125,0.146 10 false 1 4.75,2.604 4.875,2.75 0.125,0.146 10 false 2 4.115,3.385 4.24,3.531 0.125,0.146 10 false 5 4.115,2.604 4.24,2.75 0.125,0.146 10 false 3 2.833,5.427 2.958,5.573 0.125,0.146 10 false 1 2.198,4.625 2.323,4.771 0.125,0.146 10 false 5 2.833,4.625 2.958,4.771 0.125,0.146 10 false 2 2.198,5.406 2.323,5.552 0.125,0.146 10 false 3 1.865,5.948 1.99,6.094 0.125,0.146 10 false 1 1.906,6.146 2.104,6.292 0.198,0.146 10 false D6 1.229,6.188 1.354,6.333 0.125,0.146 10 false 1 1.167,6.375 1.365,6.521 0.198,0.146 10 false E1 2.229,1.833 2.521,1.979 0.292,0.146 10 false G60 2.323,2 2.531,2.146 0.208,0.146 10 false 3 2.229,2.156 2.521,2.302 0.292,0.146 10 false G58 2.323,2.333 2.531,2.479 0.208,0.146 10 false 6 2.229,2.51 2.521,2.656 0.292,0.146 10 false G60 5.396,1.656 5.604,1.802 0.208,0.146 10 false 14 5.385,1.823 5.594,1.969 0.208,0.146 10 false A7 5.396,2 5.604,2.146 0.208,0.146 10 false 13 5.385,2.177 5.594,2.323 0.208,0.146 10 false A7 5.396,4.323 5.604,4.469 0.208,0.146 10 false 48 5.385,4.51 5.594,4.656 0.208,0.146 10 false A7 5.396,2.333 5.604,2.479 0.208,0.146 10 false 52 5.385,2.5 5.604,2.646 0.219,0.146 10 false D2 2.323,2.677 2.531,2.823 0.208,0.146 10 false 8 2.229,2.854 2.521,3 0.292,0.146 10 false G57 3,3.75 3.521,3.896 0.521,0.146 10 false 9*1, 5*2 1.24,3.219 2.354,3.406 1.115,0.188 10 false Main Body ECU 0.75,6.771 1.302,6.958 0.552,0.188 10 false Battery 1.615,7.125 2.115,7.313 0.5,0.188 10 false Starter 0.625,5.698 1.271,5.885 0.646,0.188 10 false FL MAIN 4.979,2.948 5.531,3.135 0.552,0.188 10 false ST CUT 2.208,0.635 2.552,0.823 0.344,0.188 10 false IG2 1.823,1.448 2.219,1.635 0.396,0.188 10 false IG2D 1.729,1.792 2.208,1.979 0.479,0.188 10 false STSW 1.729,2.135 2.208,2.323 0.479,0.188 10 false ACCR 1.781,2.469 2.208,2.656 0.427,0.188 10 false STR2 1.865,2.813 2.208,3 0.344,0.188 10 false STR 3.688,1.156 4.031,1.344 0.344,0.188 10 false IG2 5.896,5.688 6.26,5.875 0.365,0.188 10 false ECM 5.688,1.792 6.302,1.979 0.615,0.188 10 false STSW 5.688,2.135 6.302,2.323 0.615,0.188 10 false ACCR 5.688,2.469 6.302,2.656 0.615,0.188 10 false STAR 5.688,4.479 6.021,4.667 0.333,0.188 10 false STA 1.271,3.844 1.563,4.031 0.292,0.188 10 false ST 3.094,5.01 3.385,5.198 0.292,0.188 10 false ST 0.625,5.031 1.313,5.219 0.688,0.188 10 false F/B BATT

CAUTION / NOTICE / HINT

HINT:

Read freeze frame data using the GTS. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.


PROCEDURE

1.READ VALUE USING GTS (STARTER SIGNAL)
a.

Connect the GTS to the DLC3.


b.

Start the engine.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine and ECT / Data List / Starter Signal.


e.

Check the value displayed on the GTS when the vehicle is driven at 20 km/h (12.4 mph) or more.

CAUTION:

When performing the confirmation driving pattern, obey all speed limits and traffic laws.


Result
Condition Starter Signal Proceed to
Driving at 20 km/h (12.4 mph) or more OFF A
ON B



A

B

2.INSPECT PARK/NEUTRAL POSITION SWITCH
2.INSPECT PARK/NEUTRAL POSITION SWITCH
a.

Inspect the park/neutral position switch for CVT models (See page Drivetrain>K112 (CVT)>PARK / NEUTRAL POSITION SWITCH>INSPECTION) or A/T models (See page Drivetrain>U241E (AUTOMATIC TRANSMISSION / TRANSAXLE)>PARK / NEUTRAL POSITION SWITCH>INSPECTION).

Result:
Result Proceed to
OK A
NG (CVT models) B
NG (A/T models) C




A

3.REPAIR OR REPLACE HARNESS OR CONNECTOR (STA SIGNAL CIRCUIT)

B

REPLACE PARK/NEUTRAL POSITION SWITCH

C

3.REPAIR OR REPLACE HARNESS OR CONNECTOR (STA SIGNAL CIRCUIT)
a.

Repair or replace harness or connector.



NEXT

4.CHECK WHETHER DTC OUTPUT RECURS (DTC P0617)
4.CHECK WHETHER DTC OUTPUT RECURS (DTC P0617)
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG).


c.

Turn the GTS on.



e.

Turn the engine switch off and wait for at least 30 seconds.


f.

Drive the vehicle at 24 km/h (12 mph) or more for 20 seconds or more.


g.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.


h.

Read the DTCs.

Result
Result Proceed to
DTC P0617 is output A
DTC is not output B



A

B

END