Home › Engine / Hybrid System › 2AZ-FE ENGINE CONTROL › SFI SYSTEM › 2014.09–2016.05
RM24M0E _51 Engine / Hybrid System _059541 2AZ-FE ENGINE CONTROL _0291789 SFI SYSTEM C

2AZ-FE ENGINE CONTROL  SFI SYSTEM  P2195  Oxygen (A/F) Sensor Signal Stuck Lean (Bank 1 Sensor 1)  P2196  Oxygen (A/F) Sensor Signal Stuck Rich (Bank 1 Sensor 1)  


DESCRIPTION

Refer to DTC P0031 (See page Engine / Hybrid System>2AZ-FE ENGINE CONTROL>SFI SYSTEM>P0031).

DTC No. DTC Detection Condition Trouble Area
P2195 Conditions (a) and (b) continue for 5 seconds or more (2 trip detection logic):

(a) Air fuel ratio sensor voltage is higher than 3.8 V.

(b) Heated oxygen sensor voltage is 0.21 V or higher.


·

Open or short in air fuel ratio sensor (sensor 1) circuit

·

Air fuel ratio sensor (sensor 1)

·

Intake system

·

Fuel pressure

·

Fuel injector

·

ECM


While the fuel-cut operation is performed (during vehicle deceleration), the air fuel ratio sensor current is 3.6 mA or higher for 3 seconds (2 trip detection logic).
·

Air fuel ratio sensor (sensor 1)

·

ECM


P2196 Conditions (a) and (b) continue for 5 seconds or more (2 trip detection logic):

(a) Air fuel ratio sensor voltage is less than 2.8 V.

(b) Heated oxygen sensor voltage is less than 0.69 V.


·

Open or short in air fuel ratio sensor (sensor 1) circuit

·

Air fuel ratio sensor (sensor 1)

·

Intake system

·

Fuel pressure

·

Fuel injector

·

ECM


While the fuel-cut operation is performed (during vehicle deceleration), the air fuel ratio sensor current is less than 1.0 mA for 3 seconds (2 trip detection logic).
·

Air fuel ratio sensor (sensor 1)

·

ECM



HINT:
·

When any of these DTCs is stored, check the air fuel ratio sensor voltage output by entering the following menus on the intelligent tester: Powertrain / Engine and ECT / Data List / All Data / AFS Voltage B1S1.

·

Short-term fuel trim values can also be read using the intelligent tester.

·

The ECM regulates the voltages at the A1A+ and A1A- terminals of the ECM to a constant level. Therefore, the air fuel ratio sensor voltage output cannot be confirmed without using the intelligent tester.

·

If an air fuel ratio sensor malfunction is detected, the ECM stores a DTC.



MONITOR DESCRIPTION

Sensor Voltage Detection Monitor

Under air fuel ratio feedback control, If the air fuel ratio sensor output voltage is less than 2.8 V (very rich condition) for 5 seconds despite the heated oxygen sensor output voltage being less than 0.69 V, the ECM stores DTC P2196. Alternatively, if the air fuel ratio sensor output voltage is higher than 3.8 V (very lean condition) for 5 seconds despite the heated oxygen sensor output voltage being 0.21 V or higher, DTC P2195 is stored.


Sensor Current Detection Monitor

A rich air fuel mixture causes a low air fuel ratio sensor current, and a lean air fuel mixture causes a high air fuel ratio sensor current. Therefore, the sensor output becomes low during acceleration, and it becomes high during deceleration with the throttle valve fully closed. The ECM monitors the air fuel ratio sensor current during fuel-cut and detects any abnormal current values.

If the air fuel ratio sensor output is 3.6 mA or higher for more than 3 seconds of cumulative time, the ECM interprets this as a malfunction in the air fuel ratio sensor and stores DTC P2195 (stuck on high side). If the air fuel ratio sensor output is less than 1.0 mA for more than 3 seconds of cumulative time, the ECM stores DTC P2196 (stuck on low side).


A107165E94
2.365,2.281 2.198,1.552 2.198,1.552 2.302,1.552 false 4.396,2.281 4.229,1.552 4.229,1.552 4.333,1.552 false 5.771,2.292 5.688,1.583 5.688,1.583 5.771,1.583 false 0.177,0.083 3.125,0.281 2.948,0.198 10 false Air Fuel Ratio Sensor Current Monitor 2.896,0.375 6.646,0.573 3.75,0.198 10 false Cumulative Time "t" = t1 + t2 = 3 seconds or more 0.583,1.073 1.365,1.271 0.781,0.198 10 false Fuel-cut 1.5,0.865 1.813,1.063 0.313,0.198 10 false ON 1.438,1.156 1.854,1.354 0.417,0.198 10 false OFF 2.365,1.448 3.729,1.646 1.365,0.198 10 false Delay (3 seconds) 4.365,1.438 5.563,1.865 1.198,0.427 10 true Delay (3 seconds) 5.802,1.438 7.01,1.885 1.208,0.448 10 true Delay (3 seconds) 2.354,3.615 3.552,3.969 1.198,0.354 10 true 3 seconds or more 2.323,4.229 4.083,4.427 1.76,0.198 10 false Normal Sensor Output 4.625,4.229 6.292,4.427 1.667,0.198 10 false Abnormal Sensor Output 6.344,4.229 6.813,4.427 0.469,0.198 10 false Time 0.406,2.198 2.052,2.396 1.646,0.198 10 false Sensor Current (mA) 0.406,2.813 2.052,3.01 1.646,0.198 10 false High Side Threshold 0.458,3.469 2.021,3.667 1.563,0.198 10 false Low Side Threshold 4.688,3.698 4.906,3.896 0.219,0.198 10 false t1 6.01,3.698 6.229,3.896 0.219,0.198 10 false t2

CONFIRMATION DRIVING PATTERN

A293210E10
2.469,1.51 2.917,0.76 2.917,0.76 2.708,0.76 false 4.438,1.521 5.052,1.521 false 4.51,0.625 4.896,1.781 false 5.865,0.865 5.49,1.76 false 5.385,2.198 6.396,2.198 false 4.646,2.948 4.75,2.948 4.75,2.948 4.75,2.729 false 5.667,3.167 5.865,3.167 5.865,3.167 5.5,2.74 false 3.958,3.354 4.365,3.563 false 0.031,0.25 3.031,0.51 3,0.26 10 false Engine Coolant Temperature: 75°C or higher 1.083,0.677 2.844,1.031 1.76,0.354 10 false Between 60 and 100 km/h 0.75,2.281 1.302,2.698 0.552,0.417 10 false Idling 1.292,2.802 2.208,3.24 0.917,0.438 10 false Warming up 2.49,2.854 3.198,3.365 0.708,0.51 10 false 10 minutes or more 0.177,0.885 1.219,1.26 1.042,0.375 10 false Vehicle Speed 1.302,2.146 1.719,2.531 0.417,0.385 10 false [A] 2.75,1.302 3.167,1.688 0.417,0.385 10 false [B] 3.563,2.115 3.979,2.5 0.417,0.385 10 false [C] 5.135,1.281 5.552,1.667 0.417,0.385 10 false [D] 5.521,1.667 5.938,2.052 0.417,0.385 10 false [E] 4.667,0.906 5.688,1.208 1.021,0.302 10 false At least 3 times 3.385,0.479 4.5,0.969 1.115,0.49 10 false Accelerator Pedal Depressed 3.406,1.427 4.479,1.688 1.073,0.26 10 false 60 km/h or more 5.76,0.479 6.969,0.99 1.208,0.51 10 false Accelerator Pedal Released (Fuel-cut) 6.438,2.115 6.99,2.375 0.552,0.26 10 false 10 km/h 6.333,2.573 6.885,2.833 0.552,0.26 10 false Time 3.417,2.854 4.813,3.177 1.396,0.323 10 false 10 seconds or more 4.469,3.073 5.865,3.396 1.396,0.323 10 false 4 seconds or more 4.406,3.51 5.802,3.802 1.396,0.292 10 false Refer to figure below 6.083,3.146 6.635,3.406 0.552,0.26 10 false [F]

A232909E56
3.635,2.615 3.958,0.885 false 3.365,2.625 2.156,0.719 2.156,0.719 2.281,0.719 false 0.104,0.031 3.042,0.229 2.938,0.198 10 false Driving Pattern Detail for [C] through [E]: 0.177,0.563 1.948,0.76 1.771,0.198 10 false Reference Engine Speed 2.813,0.188 6.969,0.385 4.156,0.198 10 false Cumulative Detection Period "t" = t1 + t2 + t3 = 3 seconds or more 0.833,1.854 1.604,2.052 0.771,0.198 10 false 2500 rpm 0.833,2.219 1.604,2.417 0.771,0.198 10 false 1400 rpm 1.094,2.396 1.51,2.594 0.417,0.198 10 false Idling 2.188,2.938 2.604,3.135 0.417,0.198 10 false Idling 3.188,3.063 3.885,3.427 0.698,0.365 10 false 4 seconds or more 4.406,3.052 5.104,3.417 0.698,0.365 10 false 4 seconds or more 5.625,3.052 6.333,3.417 0.708,0.365 10 false 4 seconds or more 2.188,2.51 2.406,2.708 0.219,0.198 10 false [C] 2.823,1.156 3.063,1.354 0.24,0.198 10 false [D] 3.458,1.542 3.656,1.74 0.198,0.198 10 false [E] 2.365,0.604 3.552,0.802 1.188,0.198 10 false Delay (3 seconds) 4,0.792 5.438,0.99 1.438,0.198 10 false Detection Period t1 4.813,2.385 4.969,2.583 0.156,0.198 10 false t2 6.031,2.385 6.188,2.583 0.156,0.198 10 false t3 6.479,2.76 6.865,2.958 0.385,0.198 10 false Time

1.

Connect the intelligent tester to the DLC3.

2.

Turn the engine switch on (IG).

3.

Turn the tester on.

4.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

5.

Turn the engine switch off and wait for at least 30 seconds.

6.

Turn the engine switch on (IG) and turn the tester on.

7.

Start the engine and warm it up until the engine coolant temperature reaches 75°C (167°F) or higher [A].

8.

On the tester, enter the following menus to check the fuel-cut status: Powertrain / Engine and ECT / Data List / All Data / Idle Fuel Cut.

9.

Drive the vehicle at a speed between 60 and 100 km/h (37 and 62 mph) for at least 10 minutes [B].

CAUTION:

When performing the confirmation driving pattern, obey all speed limits and traffic laws.


10.

With the shift lever in S [C], accelerate the vehicle to 60 km/h (37 mph) or more by depressing the accelerator pedal for at least 10 seconds [D].

CAUTION:

When performing the confirmation driving pattern, obey all speed limits and traffic laws.


11.

Soon after performing step [D] above, release the accelerator pedal for at least 4 seconds without depressing the brake pedal in order to execute fuel-cut control [E].

HINT:

Fuel-cut is performed when the following conditions are met:

·

Accelerator pedal is fully released.

·

Engine speed is 2500 rpm or higher (fuel injection returns at 1400 rpm).



12.

Allow the vehicle to decelerate until the vehicle speed decreases to less than 10 km/h (6 mph).

13.

Repeat steps [C] through [E] above at least 3 times in one driving cycle.

14.

Enter the following menus: Powertrain / Engine and ECT / DTC [F].

15.

Read the pending DTCs.

HINT:
·

If a pending DTC is output, the system is malfunctioning.

·

If a pending DTC is not output, perform the following procedure.



16.

Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.

17.

Input the DTC: P2195 or P2196.

18.

Check the DTC judgment result.

Tester Display Description
NORMAL
·

DTC judgment completed

·

System normal


ABNORMAL
·

DTC judgment completed

·

System abnormal


INCOMPLETE
·

DTC judgment not completed

·

Perform driving pattern after confirming DTC enabling conditions


N/A
·

Unable to perform DTC judgment

·

Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit



HINT:
·

If the judgment result shows NORMAL, the system is normal.

·

If the judgment result shows ABNORMAL, the system has a malfunction.

·

If the judgment result shows INCOMPLETE or N/A, perform steps [B] through [F] again.




WIRING DIAGRAM

A235535E01
0.828,3.914 1.351,4.101 0.522,0.187 10 Battery 0.689,2.784 1.279,2.926 0.590,0.141 10 FL MAIN 0.689,1.926 1.338,2.067 0.649,0.141 10 F/B BATT 0.996,1.206 1.242,1.351 0.246,0.145 10 EFI 1.687,1.667 2.315,1.816 0.628,0.149 10 EFI MAIN 3.484,0.947 3.676,1.097 0.192,0.151 10 +B 3.484,1.707 3.833,1.857 0.348,0.151 10 A1A- 3.886,0.947 4.288,1.097 0.402,0.151 10 HA1A 3.914,1.707 4.278,1.857 0.364,0.151 10 A1A+ 5.632,0.975 6.034,1.125 0.402,0.151 10 HA1A 5.272,0.904 5.535,1.055 0.264,0.151 10 109 4.33,0.975 4.437,1.125 0.107,0.151 10 1 3.3,0.975 3.425,1.125 0.125,0.151 10 2 2.34,0.975 2.465,1.125 0.125,0.151 10 3 1.549,0.975 1.673,1.125 0.125,0.151 10 5 2.34,1.279 2.465,1.430 0.125,0.151 10 1 1.549,1.279 1.673,1.430 0.125,0.151 10 2 4.33,1.77 4.451,1.920 0.121,0.151 10 3 3.3,1.77 3.418,1.920 0.118,0.151 10 4 5.3,1.076 5.508,1.227 0.208,0.151 10 D2 5.272,1.682 5.535,1.833 0.264,0.151 10 112 5.3,1.854 5.508,2.004 0.208,0.151 10 D2 5.272,2.348 5.535,2.498 0.264,0.151 10 113 5.3,2.519 5.508,2.670 0.208,0.151 10 D2 5.314,3.742 5.498,3.892 0.184,0.151 10 44 5.314,3.913 5.522,4.064 0.208,0.151 10 A7 5.632,1.755 5.996,1.905 0.364,0.151 10 A1A+ 5.632,2.422 5.996,2.572 0.364,0.151 10 A1A- 5.632,3.805 6.079,3.956 0.448,0.151 10 MREL 3.621,2.191 4.363,2.334 0.742,0.142 10 A/F Sensor 3.292,2.191 3.583,2.334 0.291,0.142 10 D56 4.591,1.363 5.171,1.508 0.580,0.145 10 Shielded 6.055,4.572 6.402,4.724 0.347,0.152 10 ECM

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following inspection procedure.


HINT:
·

Sensor 1 refers to the sensor closest to the engine assembly.

·

Sensor 2 refers to the sensor farthest away from the engine assembly.

·

Read freeze frame data using the intelligent tester. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.

·

A low air fuel ratio sensor voltage could be caused by a rich air fuel mixture. Check for conditions that would cause the engine to run rich.

·

A high air fuel ratio sensor voltage could be caused by a lean air fuel mixture. Check for conditions that would cause the engine to run lean.



PROCEDURE

1.CHECK ANY OTHER DTCS OUTPUT (IN ADDITION TO DTC P2195 OR P2196)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the engine switch on (IG).


c.

Turn the tester on.


d.

Enter the following menus: Powertrain / Engine and ECT / DTC.


e.

Read the DTCs.

Result
Result Proceed to
DTC P2195 or P2196 is output A
DTC P2195 or P2196 and P0136, P0137 or P0138 are output
DTC P2195 or P2196 and other DTCs are output B

HINT:

If any DTCs relating to the air fuel ratio sensor (DTCs for the air fuel ratio sensor heater or air fuel ratio sensor admittance) are output, troubleshoot those DTCs first.




A

2.CONFIRM IF VEHICLE HAS RUN OUT OF FUEL IN PAST

B

2.CONFIRM IF VEHICLE HAS RUN OUT OF FUEL IN PAST
a.

Has the vehicle run out of fuel in the past?



YES

3.CHECK WHETHER DTC OUTPUT RECURS (DTC P2195 OR P2196)

NO

4.READ VALUE USING INTELLIGENT TESTER (AIR FUEL RATIO SENSOR CURRENT)
3.CHECK WHETHER DTC OUTPUT RECURS (DTC P2195 OR P2196)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the engine switch on (IG).


c.

Turn the tester on.



e.

Turn the engine switch off and wait for at least 30 seconds.


f.

Turn the engine switch on (IG).


g.

Turn the tester on.


h.

Start the engine and warm it up.


i.

Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.


j.

Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.


k.

Input the DTC: P2195 or P2196.


l.

Check the DTC judgment result.

Result
Result Proceed to
NORMAL (DTC is not output) A
ABNORMAL (DTC P2195 or P2196 is output) B



A

DTC CAUSED BY RUNNING OUT OF FUEL

B

4.READ VALUE USING INTELLIGENT TESTER (AIR FUEL RATIO SENSOR CURRENT)
4.READ VALUE USING INTELLIGENT TESTER (AIR FUEL RATIO SENSOR CURRENT)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the engine switch on (IG).


c.

Turn the tester on.



e.

Enter the following menus: Powertrain / Engine and ECT / Data List / All Data / AFS Current B1S1.


f.

Check the test value of the air fuel ratio sensor output current during fuel-cut, referring to the Driving Pattern Detail for [C] through [E] in the Confirmation Driving Pattern.

HINT:
·

To measure the air fuel ratio sensor current precisely, perform the fuel-cut operation as long as possible.

·

If it is difficult to measure the air fuel ratio sensor current, use the snapshot function of the tester.



Result
Test Value Proceed to
Within normal range (1.0 mA or higher, and lower than 3.6 mA) A
Outside normal range (lower than 1.0 mA, or 3.6 mA or higher) B



A

5.READ VALUE USING INTELLIGENT TESTER (OUTPUT VOLTAGE OF AIR FUEL RATIO SENSOR)

B

14.REPLACE AIR FUEL RATIO SENSOR
5.READ VALUE USING INTELLIGENT TESTER (OUTPUT VOLTAGE OF AIR FUEL RATIO SENSOR)
a.

Connect the intelligent tester to the DLC3.


b.

Start the engine.


c.

Turn the tester on.


d.

Warm up the air fuel ratio sensor at an engine speed of 2500 rpm for 90 seconds.


e.

Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the Injection Volume for A/F Sensor / All Data / AFS Voltage B1S1 and O2S B1S2.


f.

Perform the Control the Injection Volume for A/F Sensor operation with the engine idling.


g.

Monitor the output voltages of the air fuel ratio and heated oxygen sensors (AFS Voltage B1S1 and O2S B1S2) displayed on the tester.

HINT:
·

The Control the Injection Volume for A/F Sensor operation lowers the fuel injection volume by 12.5% or increases the injection volume by 12.5%.

·

The air fuel ratio sensor has an output delay of a few seconds and the heated oxygen sensor has a maximum output delay of approximately 20 seconds.

·

If the sensor output voltage does not change (almost no reaction) while performing the Active Test, the sensor may be malfunctioning.



Tester Display
(Sensor)
Injection Volume Status Voltage
AFS Voltage B1S1
(Air fuel ratio)
12.5% Rich Below 3.1 V
-12.5% Lean Higher than 3.4 V
O2S B1S2
(Heated oxygen)
12.5% Rich Higher than 0.55 V
-12.5% Lean Below 0.4 V

Result
Status of AFS Voltage B1S1 Status of O2S B1S2 Air Fuel Ratio Condition and Air Fuel Ratio Sensor Condition Proceed to
Lean Lean Actual air fuel ratio lean A
Rich Rich Actual air fuel ratio rich A
Lean Lean/Rich Air fuel ratio sensor malfunction B
Rich Lean/Rich Air fuel ratio sensor malfunction B
Lean/Rich Lean/Rich Normal B

Lean: During the Control the Injection Volume for A/F Sensor Active Test, the air fuel ratio sensor output voltage (AFS Voltage B1S1) is consistently higher than 3.4 V, and the heated oxygen sensor output voltage (O2S B1S2) is consistently below 0.4 V.

Rich: During the Control the Injection Volume for A/F Sensor Active Test, the AFS Voltage B1S1 is consistently below 3.1 V, and the O2S B1S2 is consistently higher than 0.55 V.

Lean/Rich: During the Control the Injection Volume for A/F Sensor Active Test, the output voltage of the air fuel ratio sensor and the heated oxygen sensor alternates correctly.




A

6.CHECK INTAKE SYSTEM

B

14.REPLACE AIR FUEL RATIO SENSOR
6.CHECK INTAKE SYSTEM
a.

Check the intake system for vacuum leaks.

OK:

No leaks in the intake system.




OK

7.CHECK FOR EXHAUST GAS LEAK

NG

REPAIR OR REPLACE INTAKE SYSTEM

7.CHECK FOR EXHAUST GAS LEAK
a.

Check for exhaust gas leaks.

OK:

No gas leaks.




OK

8.CHECK FUEL PRESSURE

NG

REPAIR OR REPLACE EXHAUST SYSTEM

8.CHECK FUEL PRESSURE

OK

9.INSPECT FUEL INJECTOR

NG

16.CHECK FUEL LINE
9.INSPECT FUEL INJECTOR
a.

Check the fuel injector injection (whether fuel volume is high or low, and whether injection pattern is poor) (See page Engine / Hybrid System>2AZ-FE FUEL>FUEL INJECTOR>INSPECTION).



OK

10.REPLACE AIR FUEL RATIO SENSOR

NG

10.REPLACE AIR FUEL RATIO SENSOR
a.


NEXT

11.CHECK WHETHER DTC OUTPUT RECURS (DTC P2195 OR P2196)
11.CHECK WHETHER DTC OUTPUT RECURS (DTC P2195 OR P2196)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the engine switch on (IG).


c.

Turn the tester on.



e.

Turn the engine switch off and wait for at least 30 seconds.


f.

Turn the engine switch on (IG).


g.

Turn the tester on.


h.

Start the engine and warm it up.


i.

Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.


j.

Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.


k.

Input the DTC: P2195 or P2196.


l.

Check the DTC judgment result.

Result
Result Proceed to
ABNORMAL (DTC P2195 or P2196 is output) A
NORMAL (DTC is not output) B



A

12.REPLACE ECM

B

END

12.REPLACE ECM

NEXT

13.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
13.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
a.

Connect the intelligent tester to the DLC3.


b.

Turn the engine switch on (IG).


c.

Turn the tester on.



e.

Turn the engine switch off and wait for at least 30 seconds.


f.

Turn the engine switch on (IG).


g.

Turn the tester on.


h.

Start the engine and warm it up.


i.

Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.


j.

Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.


k.

Input the DTC: P2195 or P2196.


l.

Check the DTC judgment result.

Result
Tester Display Description
NORMAL
·

DTC judgment completed

·

System normal


ABNORMAL
·

DTC judgment completed

·

System abnormal


INCOMPLETE
·

DTC judgment not completed

·

Perform driving pattern after confirming DTC enabling conditions


N/A
·

Unable to perform DTC judgment

·

Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit





NEXT

END

14.REPLACE AIR FUEL RATIO SENSOR
a.


NEXT

15.CHECK WHETHER DTC OUTPUT RECURS (DTC P2195 OR P2196)
15.CHECK WHETHER DTC OUTPUT RECURS (DTC P2195 OR P2196)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the engine switch on (IG).


c.

Turn the tester on.



e.

Turn the engine switch off and wait for at least 30 seconds.


f.

Turn the engine switch on (IG).


g.

Turn the tester on.


h.

Start the engine and warm it up.


i.

Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.


j.

Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.


k.

Input the DTC: P2195 or P2196.


l.

Check the DTC judgment result.

Result
Result Proceed to
NORMAL (DTC is not output) A
ABNORMAL (DTC P2195 or P2196 is output) B



A

END

B

16.CHECK FUEL LINE
a.

Check the fuel lines for leaks or blockage.



OK

NG

REPAIR OR REPLACE FUEL LINE