Home › Engine / Hybrid System › 2GR-FE FUEL › FUEL INJECTOR
RM24M0E _51 Engine / Hybrid System _059543 2GR-FE FUEL _0291803 FUEL INJECTOR A

2GR-FE FUEL  FUEL INJECTOR  REMOVAL  


PROCEDURE

Hide 1. DISCHARGE FUEL SYSTEM PRESSURE

Hide 2.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).


Hide 51442 3.REMOVE NO. 2 ENGINE UNDER COVER

Hide 85291B 6.REMOVE FRONT WIPER ARM AND BLADE ASSEMBLY LH

Hide 85291A 7.REMOVE FRONT WIPER ARM AND BLADE ASSEMBLY RH

Hide 53867H 8.REMOVE FRONT FENDER TO COWL SIDE SEAL LH

Hide 53866J 9.REMOVE FRONT FENDER TO COWL SIDE SEAL RH

Hide 55781F 10.REMOVE COWL TOP VENTILATOR LOUVER

Hide 47202 11.REMOVE BRAKE MASTER CYLINDER RESERVOIR BRACKET

Hide 55712 12.REMOVE FRONT COWL TOP OUTSIDE PANEL WITH WINDSHIELD WIPER MOTOR AND LINK

Hide 17190 15.REMOVE INTAKE AIR SURGE TANK ASSEMBLY

a.
A129464E24
0.521,0.271 0.813,0.458 0.292,0.188 10 true (*2) 2.76,0.708 3.052,0.927 0.292,0.219 10 true (*3) 2.042,1.781 2.302,1.938 0.26,0.156 10 false (*3) 0.573,1.073 0.854,1.271 0.281,0.198 10 true (*1) 1.031,1.906 1.313,2.104 0.281,0.198 10 true (*1)

Disconnect the 2 water by-pass hoses from the throttle with motor body assembly. (*1)


b.

Disconnect the vapor feed hose. (*2)


c.

Disconnect the throttle with motor body assembly connector and clamp. (*3)


d.
U188455E02
1.427,0.229 1.719,0.417 0.292,0.188 10 true (*4) 2.24,0.333 2.531,0.49 0.292,0.156 10 false (*5)

Disconnect the No. 1 ventilation hose. (*4)


e.

Disconnect the union to check valve hose. (*5)


f.
A129467

Disconnect the connector.


g.
A129468E12
0.354,1.656 0.698,1.896 0.344,0.24 0.042,0.073 0.302,0.26 0.26,0.188 10 true (*2) 2.875,0.365 3.135,0.552 0.26,0.188 10 true (*2) 2.823,1.698 3.083,1.885 0.26,0.188 10 true (*2) 0.365,1.688 0.625,1.875 0.26,0.188 10 false (*2) 1.542,1.469 1.802,1.656 0.26,0.188 10 true (*1) 1.865,1.271 2.125,1.458 0.26,0.188 10 true (*1) 2.135,1.479 2.396,1.667 0.26,0.188 10 true (*1) 1.323,1.24 1.583,1.427 0.26,0.188 10 true (*1)

Using a 5 mm socket hexagon wrench, remove the 4 bolts. (*1)


h.

Remove the 2 nuts, 2 bolts, and intake air surge tank. (*2)


i.

Remove the gasket from the intake air surge tank.


Hide 23901 16.DISCONNECT FUEL TUBE SUB-ASSEMBLY

a.
A129469E04
2.344,1.76 2.344,2.24 false 2.74,3.198 2.74,2.844 2.74,2.844 2.615,2.844 false 3.01,3.708 3.01,4.052 false 2.052,3.729 2.146,4.115 2.146,4.115 2.26,3.729 false 1.25,3.344 1.25,3.01 1.25,3.01 1.167,3.01 false 1.167,0.323 1.573,0.594 0.406,0.271 10 true Pinch 1.292,1.656 1.688,1.958 0.396,0.302 10 false Pinch 1.438,2.26 2.885,2.563 1.448,0.302 10 false No. 2 Fuel Pipe Clamp 1.833,0.26 2.135,0.49 0.302,0.229 10 true Pull 2.854,4.073 3.167,4.375 0.313,0.302 10 false Pipe 1.542,2.729 2.563,3.031 1.021,0.302 10 false Tube Connector 0.375,2.917 1.104,3.219 0.729,0.302 10 false Nylon Tube 1.917,4.146 2.406,4.448 0.49,0.302 10 false O-Ring

Remove the No. 2 fuel pipe clamp.


b.

Pinch the tube connector and pull out the fuel pipe.

NOTICE:
·

Check that there is no dirt or other foreign objects around the connector before disconnecting it. Clean the connector as necessary.

·

It is necessary to prevent dirt or foreign objects from entering the quick connector. If dirt or foreign matter gets in the connector, the O-rings may not seal properly.

·

Only disconnect the quick connector by hand.

·

Do not bend, kink or twist the nylon tubes. Protect the connector by covering it with a plastic bag.

·

If the pipe and the connector are stuck, carefully try wiggling or pushing and pulling on the connector to release it. Pull the connector off the pipe carefully.




Hide 23250 17.REMOVE FUEL INJECTOR ASSEMBLY

a.
A137341

Disconnect the 6 fuel injector connectors.


b.
A129471

Remove the 5 bolts and fuel delivery pipe sub-assembly together with the 6 fuel injectors.

NOTICE:

Be careful not to drop the fuel injectors when removing the fuel delivery pipe.



c.
U113569

Remove the 6 injector vibration insulators from the intake manifold.


d.
A129473

Pull out the fuel injectors from the fuel delivery pipe.

NOTICE:

If the injectors are to be reused, reinstall according to the some cylinder they came from.



e.
A129475E13
2.865,1.427 2.865,1.583 false 2.625,1.615 3.115,1.896 0.49,0.281 10 false O-Ring

Remove the 6 O-rings from the injectors.