Home › Engine / Hybrid System › 2AZ-FE ENGINE MECHANICAL › ENGINE › from 2016.05
RM24M0E _51 Engine / Hybrid System _059548 2AZ-FE ENGINE MECHANICAL _0291830 ENGINE G

2AZ-FE ENGINE MECHANICAL  ENGINE  ON-VEHICLE INSPECTION  


PROCEDURE

Hide 1.CHECK ENGINE COOLANT

Hide 2.CHECK ENGINE OIL

Hide 17801 4.CHECK AIR CLEANER FILTER ELEMENT SUB-ASSEMBLY

a.

Remove the air cleaner cap.


b.

Remove the air cleaner filter element.


c.

Visually check that the air cleaner filter element is not excessively damaged or oily.

If necessary, replace the air cleaner filter element.


Hide 16361A 6.CHECK FAN AND GENERATOR V BELT

a.

Check the fan and generator V belt (See page Engine / Hybrid System>2AZ-FE ENGINE MECHANICAL>DRIVE BELT>ON-VEHICLE INSPECTION).

HINT:

It is unnecessary to measure the tension and flexibility of the V belt due to the V belt auto tensioner.



Hide 7.CHECK IGNITION TIMING

NOTICE:
·

Turn all the electrical systems and the A/C off.

·

Inspect the ignition timing with the cooling fan off.

·

When checking the ignition timing, shift the transmission to the neutral position.



a.

Warm up and stop the engine.


b.

When using the intelligent tester:

i.

Connect the intelligent tester to the DLC3.


ii.

Turn the ignition switch to ON.


iii.

Turn the intelligent tester on.


iv.

Enter the following menus: Power Train / Engine and ECT / Data List / IGN Advance


v.

Start the engine.


vi.

According to the display on the intelligent tester, read the Data List.

Standard ignition timing:

5 to 15° BTDC at idle



vii.

Check that the ignition timing advances immediately when the engine speed is increased.


viii.

Turn the ignition switch off.


ix.

Disconnect the intelligent tester from the DLC3.



c.

When not using the intelligent tester:

i.
A112264

Open the ignition cover located on the right of the No. 4 ignition coil.


ii.

Pull out the wire harness from the IG cover.


iii.

Connect the timing light to the wire harness.

NOTICE:

Use a timing light that detects the primary signal.



iv.
H100769E05
1.896,0.392 2.172,0.577 0.276,0.185 10 CG 2.193,1.707 2.469,1.892 0.275,0.185 10 TC 1.799,1.48 2.159,1.762 false 1.599,0.906 1.867,0.521 false 1.469,1.761 1.895,1.912 0.426,0.150 10 DLC3

Using SST, connect terminals 13 (TC) and 4 (CG) of the DLC3.

SST
09843-18040  


v.

Allow the engine to idle and check the ignition timing.

Standard ignition timing:

8 to 12° BTDC at idle


HINT:

Run the engine at 1000 to 1300 rpm for 5 seconds, then check that the engine speed returns to the idling speed.



vi.

Disconnect SST from terminals 13 (TC) and 4 (CG) of the DLC3.


vii.

Allow the engine to idle and check the ignition timing.

Standard ignition timing:

5 to 15° BTDC at idle



viii.

Check that the ignition timing advances immediately when the engine speed is increased.


ix.

Turn the ignition switch off.


x.

Remove the timing light.


xi.

Close the IG cover.



Hide 8.CHECK ENGINE IDLE SPEED

NOTICE:
·

Turn all the electrical systems and the A/C off.

·

When checking the idle speed, the transaxle should be in neutral or park.



a.

When using the intelligent tester:

i.

Connect the intelligent tester to the DLC3.


ii.

Turn the ignition switch to ON.


iii.

Turn the intelligent tester on.


iv.

Enter the following menus: Power Train / Engine and ECT / Data List / Engine Speed


v.

Start the engine.


vi.

According to the display on the intelligent tester, read the Data List.

Standard idle speed:

670 to 770 rpm



vii.

Turn the ignition switch off.


viii.

Disconnect the intelligent tester from the DLC3.



b.

When not using the intelligent tester:

i.
H100769E32
0.332,1.718 0.702,1.903 0.370,0.185 10 TAC 1.068,1.453 0.715,1.758 false 1.47,1.734 1.895,1.884 0.426,0.150 10 DLC3

Connect SST to 9 (TAC) of the DLC3 terminal, and then connect a tachometer to SST.

SST
09843-18030  


ii.

Start the engine.


iii.

Check the idle speed with the cooling fan off.

Standard idle speed:

670 to 770 rpm



iv.

Turn the ignition switch off.


v.

Remove the tachometer and disconnect SST from the DLC3.



Hide 9.CHECK COMPRESSION

a.

Warm up and stop the engine.




d.

Disconnect the 4 fuel injector connectors.


e.
U188219E02
1.688,0.177 1.563,0.177 1.563,0.177 2.083,1.26 true 1.75,0.094 3.115,0.344 1.365,0.25 10 true Compression Gauge

Insert the compression gauge into the spark plug hole.


f.

Fully open the throttle.


g.

While cranking the engine, measure the compression pressure.

Standard compression pressure:

1300 kPa (13.3 kgf/cm2, 189 psi)


Minimum compression pressure:

1000 kPa (10.0 kgf/cm2, 145 psi)


Standard difference between each cylinder:

100 kPa (1.0 kgf/cm2, 15 psi)


NOTICE:
·

Always use a fully charged battery to obtain an engine speed of 250 rpm or more.

·

Check the other cylinders in the same way.

·

This measurement must be done as quickly as possible.



If the cylinder compression is low, pour a small amount of engine oil into the cylinder through the spark plug hole and inspect again.

HINT:
·

If adding oil increases the compression, the piston rings and/or cylinder bore may be worn or damaged.

·

If pressure stays low, a valve may be stuck or seated improperly, or there may be leakage in the gasket.




h.

Connect the 4 fuel injector connectors.




Hide 10.CHECK CO/HC

HINT:

This check determines whether or not the idle CO/HC complies with local regulations.


a.

Start and warm up the engine.


b.

Run the engine at 2500 rpm for approximately 180 seconds.


c.

Insert a CO/HC meter testing probe at least 40 cm (1.3 ft.) into the tailpipe while idling.


d.

Inspect the CO/HC concentration during idle at 2500 rpm.

If the CO/HC concentration does not comply with local regulations, troubleshoot in the order given below.

i.

Check the A/F sensor and heated oxygen sensor operation.


ii.

See the table below for possible causes, then inspect the applicable parts and repair them if necessary.

CO HC Problems Causes
Normal High Rough idle 1. Faulty ignition:
- Incorrect timing
- Plugs are contaminated, shorted, or gaps are defective
2. Incorrect valve clearance
3. Leaks in intake and exhaust valve
4. Leaks in cylinders
Low High Rough idle
(Fluctuating HC reading)
1. Vacuum leakage:
- Ventilation hoses
- Intake manifold
- Throttle body
- Brake booster line
2. Lean mixture causing misfire
High High Rough idle
(Black smoke from exhaust)
1. Restricted air filter
2. Clogged PCV valve
3. Faulty SFI system:
- Faulty pressure regulator
- Faulty engine coolant temperature sensor
- Faulty mass air flow meter
- Faulty ECM
- Faulty injectors
- Faulty throttle body