In this section, the terms "cold" and "hot" refer to the temperature of the coils. "Cold" means approximately -10°C (14°F) to 50°C (122°F). "Hot" means approximately 50°C (122°F) to 100°C (212°F).
1.INSPECT IGNITION COIL ASSEMBLY
Check for DTCs.
If any DTC is present, perform troubleshooting in accordance with the procedures for that DTC.
Remove the ignition coil assembly and spark plug. (See page Engine / Hybrid System>2GR-FE IGNITION>IGNITION COIL AND SPARK PLUG>REMOVAL).
Check that sparks occur.
Disconnect the 6 fuel injector connectors.
Install the spark plugs to each ignition coil, and connect the ignition coil connectors.
Ground the spark plugs.
Check if a spark occurs at each spark plug while the engine is being cranked.
Be sure to ground the spark plugs when checking.
Replace the ignition coil if it receives an impact.
Do not crank the engine for more than 2 seconds.
Perform the spark test according to the flowchart below.
Check that the ignition coil connector is securely connected.
| Result | Proceed to |
|---|---|
| NG | Connect securely |
| OK | Go to next step |
Perform a spark test on each ignition coil.
Replace the ignition coil with a normal one.
Perform the spark test again.
| Result | Proceed to |
|---|---|
| NG | Go to next step |
| OK | Replace ignition coil |
Check the spark plug (See page Engine / Hybrid System>2GR-FE ENGINE MECHANICAL>ENGINE>ON-VEHICLE INSPECTION).
| Result | Proceed to |
|---|---|
| NG | Replace spark plug |
| OK | Go to next step |
Check the power supply to the ignition coil.
Turn the ignition switch on (IG).
Check that there is battery voltage at the ignition coil positive (+) terminal.
| Result | Proceed to |
|---|---|
| NG | Check wiring between ignition switch and ignition coil |
| OK | Go to next step |
Measure the resistance of the crankshaft position sensor (See page Engine / Hybrid System>2GR-FE ENGINE CONTROL>CRANKSHAFT POSITION SENSOR>INSPECTION).
| Result | Proceed to |
|---|---|
| NG | Replace crankshaft position sensor |
| OK | Go to next step |
Check the IGT signal from the ECM (See page Engine / Hybrid System>2GR-FE ENGINE CONTROL>SFI SYSTEM>P0351).
| Result | Proceed to |
|---|---|
| NG | Check ECM |
| OK | Repair wiring between ignition coil and ECM |
Using a 16 mm (0.63 in.) plug wrench, install the spark plugs.
Connect the 6 fuel injector connectors.
Install the ignition coil assembly (See page Engine / Hybrid System>2GR-FE IGNITION>IGNITION COIL AND SPARK PLUG>INSTALLATION).
19100P
2.INSPECT SPARK PLUG
Never use a wire brush for cleaning.
Never attempt to adjust the electrode gap on a used spark plug.
Check the electrode.
Using a megohmmeter, measure the insulation resistance.
10 MΩ or higher
If the result is 10 MΩ or less, clean the plug and measure the resistance again.
If a megohmmeter is not available, perform the following simple inspection instead.
Alternative inspection method:
Quickly accelerate the engine to 4000 rpm 5 times.
Remove the spark plugs.
Visually check the spark plug.
If the electrode is dry, the spark plug is functioning properly. If the electrode is damp, proceed to the next step.
Check the spark plug for any damage to its threads and insulator. If there is damage, replace the spark plug.
| Manufacturer | Spark Plug Type |
|---|---|
| DENSO | FK20HR11 |
Use only the listed spark plug or equivalent to ensure engine performance and smooth driveability.
Check the spark plug electrode gap.
1.4 mm (0.055 in.)
If the gap is greater than the maximum, replace the spark plug.
1.0 to 1.1 mm (0.039 to 0.043 in.)
Clean the spark plugs.
If the electrode has traces of wet carbon, clean the electrode with a spark plug cleaner and then dry it.
588 kPa (6 kgf*cm2, 85 psi)
20 seconds or less
Only use the spark plug cleaner when the electrode is free of oil. If the electrode has traces of oil, use gasoline to clean off the oil before using the spark plug cleaner.
Install ignition coil assembly and spark plug. (See page Engine / Hybrid System>2GR-FE IGNITION>IGNITION COIL AND SPARK PLUG>INSTALLATION).