The type of ignition switch on this model differs according to the specifications of the vehicle. For the expressions used in this section, refer to the "EXPRESSIONS OF IGNITION SWITCH" precaution (see page Engine / Hybrid System>2AZ-FE STARTING>STARTING SYSTEM>PRECAUTION).
19100P
1.PERFORM SPARK TEST
In this section, the terms "Cold" and "Hot" refer to the temperature of the sensor. "Cold" means approximately -10 to 50°C (14 to 122°F). "Hot" means approximately 50 to 100°C (122 to 212°F).
Check for DTCs.
If a DTC is present, perform troubleshooting in accordance with the procedure for that DTC.
Check that sparks occur.
Remove the cowl top outer panel with windshield wiper motor and link (see page Vehicle Interior>WIPER / WASHER>FRONT WIPER MOTOR>REMOVAL).
Remove the bolt and ignition coil assembly.
Using a 16 mm spark plug wrench, remove the spark plugs.
Disconnect the 4 fuel injector connectors.
Install the spark plug into the ignition coil assembly, and then connect the ignition coil connectors.
Ground the spark plug.
Check that sparks occur at the spark plug while the engine is being cranked.
Be sure to ground the spark plugs when checking them.
Do not crank the engine for more than 2 seconds.
If a spark plug has been struck or dropped, replace it.
If an ignition coil assembly has been struck or dropped, replace it.
If sparks do not occur, perform troubleshooting using the spark test flowchart.
Using a 16 mm plug wrench, install the spark plug.
Install the ignition coil assembly with the bolt.
Connect the 4 fuel injector connectors.
Install the cowl top outer panel with windshield wiper motor and link (see page Vehicle Interior>WIPER / WASHER>FRONT WIPER MOTOR>INSTALLATION).
Check for DTCs (See page Engine / Hybrid System>2AZ-FE ENGINE CONTROL>SFI SYSTEM>DTC CHECK / CLEAR).
Clear the DTCs (See page Engine / Hybrid System>2AZ-FE ENGINE CONTROL>SFI SYSTEM>DTC CHECK / CLEAR).
19500
2.INSPECT IGNITION COIL AND SPARK TEST
Check that the wire harness side connector of the ignition coil assembly is securely connected.
| Result | Action |
|---|---|
| NG | Connect securely |
| OK | Go to next step |
Perform a spark test on each ignition coil assembly.
Replace the ignition coil assembly with a known good one.
Perform the spark test again.
| Result | Action |
|---|---|
| NG | Go to next step |
| OK | Replace ignition coil assembly |
19100P
3.CHECK SPARK PLUG
Check the electrode with a megohmmeter:
Using a megohmmeter, measure the insulation resistance.
10 MΩ or more
If the result is 10 MΩ or less, clean the plug and measure the resistance again.
Check the electrode without a megohmmeter:
Quickly accelerate the engine to 4,000 rpm 5 times.
Remove the spark plug.
Visually check the spark plug.
If the electrode is dry, the spark plug is functioning properly. If the electrode is damp, proceed to the next step.
Check the spark plug for any damage on its threads and insulator.
If there is damage, replace the spark plug.
| Manufacturer | Spark plug type |
|---|---|
| DENSO | SK16R11 |
| NGK | IFR5A11 |
Check the spark plug electrode gap.
1.3 mm (0.051 in.)
If the gap is greater than the maximum, replace the spark plug.
1.0 to 1.1 mm (0.039 to 0.043 in.)
If the electrode has traces of wet carbon, clean the electrode with a spark plug cleaner and then dry it.
588 kPa (6 kgf/cm2, 85 psi)
20 seconds or less
Only use the spark plug cleaner when the electrode is free of oil. If the electrode has traces of oil, use gasoline to clean off the oil before using the spark plug cleaner.