Home › Brake › BRAKE › BRAKE MASTER CYLINDER(for LHD)
RM24M0E _54 Brake _059558 BRAKE _0291875 BRAKE MASTER CYLINDER(for LHD) A

BRAKE  BRAKE MASTER CYLINDER(for LHD)  REMOVAL  


CAUTION / NOTICE / HINT

NOTICE:
·

The master cylinder and piston are designed so that the piston can easily fall out. Prevent this by making sure that the tip of the master cylinder points downward when handling the master cylinder.

·

Make sure foreign matter does not attach to the master cylinder's piston. If foreign matter attaches, clean it off with a cloth. Then apply lithium soap base glycol grease to the entire outer circumference contact surface area of the piston.



PROCEDURE

Hide 1.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to prevent airbag and seat belt pretensioner activation.


NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).


Hide 28800 2.REMOVE BATTERY (for 2AZ-FE)

Hide 28800 3.REMOVE BATTERY (for 2GR-FE)

Hide 74431 4.REMOVE BATTERY TRAY

Hide 17705 5.REMOVE AIR CLEANER CAP SUB-ASSEMBLY (for 2AZ-FE)

Hide 17705 6.REMOVE AIR CLEANER CAP SUB-ASSEMBLY (for 2GR-FE)

Hide 17700 7.REMOVE AIR CLEANER CASE SUB-ASSEMBLY (for 2AZ-FE)

Hide 17700 8.REMOVE AIR CLEANER CASE SUB-ASSEMBLY (for 2GR-FE)

Hide 9.DRAIN BRAKE FLUID

NOTICE:

Wash off brake fluid immediately if it comes in contact with any painted surface.


Hide 47202 10.REMOVE BRAKE MASTER CYLINDER RESERVOIR SUB-ASSEMBLY

a.
C367439E01
2.792,0.271 3.063,0.542 0.271,0.271 10 false C 2.875,1.385 3.146,1.656 0.271,0.271 10 false H 2.813,1.896 3.083,2.167 0.271,0.271 10 false A 2.74,2.438 3.01,2.708 0.271,0.271 10 false E 2.896,3.708 3.167,3.979 0.271,0.271 10 false B 2.219,4.448 2.396,4.635 0.177,0.188 10 false F 1.385,4.365 1.656,4.635 0.271,0.271 10 false G 0.146,4.219 0.417,4.49 0.271,0.271 10 false D 0.198,2.542 0.469,2.813 0.271,0.271 10 false D 1.615,2.031 1.885,2.302 0.271,0.271 10 false B

Disconnect the brake fluid level warning switch connector (labeled A).


b.

Remove the 2 nuts (labeled B) and reservoir with brackets.


c.

Disconnect the No. 1 reservoir tube (labeled C) from the reservoir.


d.

Remove the 2 nuts (labeled D) and reservoir bracket (labeled E).


e.

Remove the bolt (labeled F), reservoir bracket (labeled G), nut (labeled H) and reservoir.


Hide 44781D 11.REMOVE RESERVOIR HOSE BRACKET

a.

Remove the No. 1 reservoir tube from the clamps of the bracket.


b.

Remove the nut and bracket.


Hide 47201 12.REMOVE BRAKE MASTER CYLINDER SUB-ASSEMBLY

a.

Release the vacuum pressure in the brake booster as follows.

i.

Stop the engine.


ii.

Depress the brake pedal several times.



b.
C133368E03
2.469,0.5 2.604,0.656 0.135,0.156 10 false A 2.729,1.281 2.865,1.438 0.135,0.156 10 false B 2.438,0.823 2.573,0.979 0.135,0.156 10 true B

Disconnect the No. 1 reservoir tube (labeled A) from the master cylinder.


c.

Using SST, disconnect the 2 brake lines (labeled B) from the master cylinder.

SST
09023-00101  


d.
C367715E01
1.615,1.198 1.771,1.396 0.156,0.198 10 false C 2.458,1.479 2.615,1.677 0.156,0.198 10 false C 1.906,0.479 2.063,0.677 0.156,0.198 10 false D

Remove the 2 nuts (labeled C) and vacuum check valve bracket (labeled D).


e.

Pull out the master cylinder from the brake booster.

NOTICE:
·

The master cylinder and piston are designed so that the piston can easily fall out. Prevent this by making sure that the tip of the master cylinder points downward when handling the master cylinder.

·

Make sure foreign matter does not attach to the master cylinder's piston. If foreign matter attaches, clean it off with a cloth. Then apply lithium soap base glycol grease to the entire outer circumference contact surface area of the piston.




f.

Remove the O-ring from the master cylinder.