Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › AIRBAG SYSTEM › from 2016.05
RM24M0E _58 Vehicle Interior _059562 SUPPLEMENTAL RESTRAINT SYSTEMS _0291898 AIRBAG SYSTEM C

SUPPLEMENTAL RESTRAINT SYSTEMS  AIRBAG SYSTEM  B1820/55  Short in Side Squib RH Circuit  B1821/55  Open in Side Squib RH Circuit  B1822/55  Short to GND in Side Squib RH Circuit  B1823/55  Short to B+ in Side Squib RH Circuit  


DESCRIPTION

The side squib RH circuit consists of the center airbag sensor assembly and front seat side airbag assembly RH.

The center airbag sensor assembly uses this circuit to deploy the airbag when deployment conditions are met.

These DTCs are stored when a malfunction is detected in the side squib RH circuit.

DTC No. DTC Detection Condition Trouble Area
B1820/55
·

The center airbag sensor assembly detects a line short in the side squib RH circuit during the primary check.

·

Side squib RH malfunction

·

Center airbag sensor assembly malfunction


·

No. 2 floor wire

·

Front seat wire RH

·

Front seat side airbag assembly RH (Side squib RH)

·

Center airbag sensor assembly


B1821/55
·

The center airbag sensor assembly detects an open in the side squib RH circuit.

·

Side squib RH malfunction

·

Center airbag sensor assembly malfunction


B1822/55
·

The center airbag sensor assembly detects a short to ground in the side squib RH circuit.

·

Side squib RH malfunction

·

Center airbag sensor assembly malfunction


B1823/55
·

The center airbag sensor assembly detects a short to B+ in the side squib RH circuit.

·

Side squib RH malfunction

·

Center airbag sensor assembly malfunction



WIRING DIAGRAM

C351803E14
0.708,2.5 1.5,2.885 0.792,0.385 10 false We1 0.708,2.656 3.01,3.094 2.302,0.438 10 false Front Seat Side Airbag Assembly RH (Side Squib RH) 2.01,1.885 2.802,2.271 0.792,0.385 10 false SFR- 1.99,1.063 2.781,1.448 0.792,0.385 10 false SFR+ 2.406,1.052 3.198,1.438 0.792,0.385 10 false 1 2.406,1.885 3.198,2.271 0.792,0.385 10 false 2 3.375,1.167 4.167,1.552 0.792,0.385 10 false NW2 4.5,1.042 5.292,1.427 0.792,0.385 10 false 4 4.5,1.885 5.292,2.271 0.792,0.385 10 false 3 4.708,3.208 6.771,3.479 2.063,0.271 10 false Center Airbag Sensor Assembly 4.719,3.021 5.51,3.406 0.792,0.385 10 false N9 3.375,2 4.167,2.385 0.792,0.385 10 false NW2 4.708,1.156 5.5,1.542 0.792,0.385 10 false SFR+ 4.688,2 5.479,2.385 0.792,0.385 10 false SFR- 3.417,0.969 4.208,1.354 0.792,0.385 10 false 1 3.448,1.813 4.24,2.198 0.792,0.385 10 false 2

CAUTION / NOTICE / HINT

NOTICE:

After turning the engine switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).


HINT:
·

Perform the simulation method by selecting check mode (Signal Check) using the intelligent tester (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>CHECK MODE PROCEDURE).

·

After selecting check mode (Signal Check), perform the simulation method by wiggling each connector of the airbag system or driving the vehicle on a city or rough road (See page General>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING).



PROCEDURE

1.CHECK CONNECTORS
a.
C247054E01
0.191,1.678 0.347,1.830 0.156,0.152 10 *1 0.622,0.637 0.789,0.802 0.167,0.165 10 *3 2.713,0.768 2.887,0.924 0.174,0.156 10 *2 2.261,1.077 2.378,1.230 0.117,0.153 10 A 1.95,1.077 2.067,1.230 0.117,0.153 10 B 1.47,1.077 1.597,1.230 0.127,0.153 10 C 1.16,1.077 1.287,1.230 0.127,0.153 10 D 0.685,1.077 0.812,1.230 0.127,0.153 10 E 0.388,1.077 0.515,1.230 0.127,0.153 10 F 0.274,1.231 0.274,1.665 false 1.698,1.678 1.854,1.830 0.156,0.152 10 *4 1.781,1.231 1.781,1.665 false 0.982,1.099 0.982,0.726 0.982,0.726 0.818,0.726 false

Turn the engine switch off.


b.

Disconnect the cable from the negative (-) battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.



c.

Check that the connectors are properly connected to the front seat side airbag assembly RH and center airbag sensor assembly. Also check that the connectors that link the front seat wire RH and No. 2 floor wire are properly connected.

OK:

The connectors are properly connected.


HINT:

If the connectors are not properly connected, reconnect the connectors and proceed to the next inspection.



d.

Disconnect the connectors from the front seat side airbag assembly RH and center airbag sensor assembly. Also disconnect the No. 2 floor wire from the front seat wire RH.


e.

Check that the terminals of the connectors are not deformed or damaged.

OK:

The terminals are not deformed or damaged.



f.

Check that the short springs of the activation prevention mechanisms of the No. 2 floor wire connector and front seat wire RH connector are not deformed or damaged.

OK:

The short springs are not deformed or damaged.


Text in Illustration
*1 Front Seat Side Airbag Assembly RH
*2 Center Airbag Sensor Assembly
*3 Front Seat Wire RH
*4 No. 2 Floor Wire



OK

2.CHECK FRONT SEAT SIDE AIRBAG ASSEMBLY RH

NG

REPLACE WIRE HARNESS

2.CHECK FRONT SEAT SIDE AIRBAG ASSEMBLY RH
a.
U189605E01
0.664,0.37 0.820,0.521 0.156,0.152 10 *1 2.596,0.593 2.771,0.749 0.174,0.156 10 *2 2.172,0.902 2.288,1.055 0.117,0.153 10 A 2.016,0.902 2.132,1.055 0.117,0.153 10 B 1.526,0.902 1.653,1.055 0.127,0.153 10 C 1.369,0.902 1.496,1.055 0.127,0.153 10 D 0.892,0.902 1.019,1.055 0.127,0.153 10 E 0.494,0.902 0.621,1.055 0.127,0.153 10 F 0.319,1.597 0.487,1.762 0.167,0.165 10 *a 2.282,2.258 2.593,2.409 0.310,0.151 10 SST 2.034,2.345 2.25,2.345 false 0.464,2.103 0.770,2.259 0.306,0.156 10 We1 0.387,0.916 0.387,0.454 0.387,0.454 0.645,0.454 false

Connect the No. 2 floor wire to the front seat wire RH and center airbag sensor assembly.


b.

Connect SST (resistance 2.1 Ω) to connector E.

CAUTION:

Never connect a tester to the front seat side airbag assembly RH for measurement, as this may lead to a serious injury due to airbag deployment.


NOTICE:
·

Do not forcibly insert SST into the terminals of the connector when connecting it.

·

Insert SST straight into the terminals of the connector.




SST
09843-18061  

c.

Connect the cable to the negative (-) battery terminal.



e.

Turn the engine switch off.


f.

Turn the engine switch on (IG), and wait for at least 60 seconds.


g.

Check for DTCs (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR).

OK:

DTC B1820/55, B1821/55, B1822/55 or B1823/55 is not output.


Result:
Result Proceed to
OK (for Manual Seat) A
OK (for Power Seat) B
NG C


HINT:

Codes other than DTCs B1820/55, B1821/55, B1822/55 and B1823/55 may be output at this time, but they are not related to this check.



h.

Turn the engine switch off.


i.

Disconnect the cable from the negative (-) battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.



j.

Disconnect SST from connector E.

Text in Illustration
*1 Front Seat Side Airbag Assembly RH
*2 Center Airbag Sensor Assembly
*a Front view of wire harness connector
(to Front Seat Side Airbag Assembly RH)



A

REPLACE FRONT SEAT SIDE AIRBAG ASSEMBLY RH (FRONT SEAT ASSEMBLY RH)

B

REPLACE FRONT SEAT SIDE AIRBAG ASSEMBLY RH (FRONT SEAT ASSEMBLY RH)

C

3.CHECK SIDE SQUIB RH CIRCUIT
3.CHECK SIDE SQUIB RH CIRCUIT
a.
U189597E02
0.385,0.854 0.385,0.385 0.385,0.385 0.646,0.385 false 1.76,2.656 2.031,2.656 true 1.188,2.656 1.458,2.656 true 0.667,0.302 0.823,0.458 0.156,0.156 10 false *1 2.583,0.542 2.76,0.698 0.177,0.156 10 false *2 2.177,0.833 2.292,0.99 0.115,0.156 10 false A 1.854,0.833 1.969,0.99 0.115,0.156 10 false B 1.406,0.833 1.531,0.99 0.125,0.156 10 false C 1.24,0.833 1.365,0.99 0.125,0.156 10 false D 0.802,0.833 0.927,0.99 0.125,0.156 10 false E 0.5,0.833 0.625,0.99 0.125,0.156 10 false F 0.281,1.76 0.448,1.927 0.167,0.167 10 false *a 0.469,2.115 0.771,2.271 0.302,0.156 10 false We1 2.063,2.563 2.417,2.708 0.354,0.146 10 false SFR- 0.74,2.563 1.135,2.708 0.396,0.146 10 false SFR+

Disconnect the No. 2 floor wire from the center airbag sensor assembly.


b.

Check for a short to B+ in the circuit.

i.

Connect the cable to the negative (-) battery terminal.


ii.

Turn the engine switch on (IG).


iii.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
We1-1 (SFR+) - Body ground Engine switch on (IG) Below 1 V
We1-2 (SFR-) - Body ground Engine switch on (IG) Below 1 V



iv.

Turn the engine switch off.


v.

Disconnect the cable from the negative (-) battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.




c.

Check for an open in the circuit.

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
We1-1 (SFR+) - We1-2 (SFR-) Always Below 1 Ω




d.

Check for a short to ground in the circuit.

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
We1-1 (SFR+) - Body ground Always 1 MΩ or higher
We1-2 (SFR-) - Body ground Always 1 MΩ or higher




e.

Check for a short in the circuit.

i.

Release the activation prevention mechanism built into connector B (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DIAGNOSIS SYSTEM).


ii.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
We1-1 (SFR+) - We1-2 (SFR-) Always 1 MΩ or higher



iii.

Restore the released activation prevention mechanism of connector B to the original condition.

Text in Illustration
*1 Front Seat Side Airbag Assembly RH
*2 Center Airbag Sensor Assembly
*a Front view of wire harness connector
(to Front Seat Side Airbag Assembly RH)




OK

4.CHECK DTC

NG

5.CHECK NO. 2 FLOOR WIRE
4.CHECK DTC
a.
C245654E01
0.728,0.774 0.884,0.926 0.156,0.152 10 *1 2.533,0.996 2.707,1.152 0.174,0.156 10 *2 2.069,1.306 2.186,1.459 0.117,0.153 10 A 1.913,1.306 2.029,1.459 0.117,0.153 10 B 1.39,1.306 1.517,1.459 0.127,0.153 10 C 1.233,1.306 1.360,1.459 0.127,0.153 10 D 0.719,1.306 0.846,1.459 0.127,0.153 10 E 0.558,1.306 0.685,1.459 0.127,0.153 10 F 0.452,1.32 0.452,0.859 0.452,0.859 0.709,0.859 false

Connect the connectors to the front seat side airbag assembly RH and the center airbag sensor assembly.


b.

Connect the cable to the negative (-) battery terminal.



d.

Turn the engine switch off.


e.

Turn the engine switch on (IG), and wait for at least 60 seconds.


f.

Check for DTCs (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR).

OK:

DTC B1820/55, B1821/55, B1822/55 or B1823/55 is not output.


HINT:

Codes other than DTCs B1820/55, B1821/55, B1822/55 and B1823/55 may be output at this time, but they are not related to this check.


Text in Illustration
*1 Front Seat Side Airbag Assembly RH
*2 Center Airbag Sensor Assembly



OK

NG

5.CHECK NO. 2 FLOOR WIRE
a.
U189598E02
0.323,0.813 0.323,0.344 0.323,0.344 0.583,0.344 false 1.781,0.813 1.781,0.344 1.781,0.344 1.938,0.344 false 1.771,2.635 2.021,2.635 true 1.198,2.635 1.448,2.635 true 1.01,0.958 1.01,1.292 false 0.594,0.26 0.75,0.417 0.156,0.156 10 false *1 2.656,0.51 2.833,0.667 0.177,0.156 10 false *2 2.25,0.792 2.365,0.948 0.115,0.156 10 false A 1.948,0.792 2.063,0.948 0.115,0.156 10 false B 1.49,0.792 1.615,0.948 0.125,0.156 10 false C 1.177,0.792 1.302,0.948 0.125,0.156 10 false D 0.74,0.792 0.865,0.948 0.125,0.156 10 false E 0.427,0.792 0.552,0.948 0.125,0.156 10 false F 0.302,1.781 0.469,1.948 0.167,0.167 10 false *a 0.438,2.135 0.771,2.292 0.333,0.156 10 false NW2 1.958,0.26 2.115,0.417 0.156,0.156 10 false *4 2.052,2.542 2.448,2.708 0.396,0.167 10 false SFR- 0.729,2.542 1.167,2.74 0.438,0.198 10 false SFR+ 0.938,1.302 1.083,1.458 0.146,0.156 10 false *3

Disconnect the No. 2 floor wire from the front seat wire RH.


b.

Check for a short to B+ in the circuit.

i.

Connect the cable to the negative (-) battery terminal.


ii.

Turn the engine switch on (IG).


iii.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
NW2-1 (SFR+) - Body ground Engine switch on (IG) Below 1 V
NW2-2 (SFR-) - Body ground Engine switch on (IG) Below 1 V



iv.

Turn the engine switch off.


v.

Disconnect the cable from the negative (-) battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.




c.

Check for an open in the circuit.

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
NW2-1 (SFR+) - NW2-2 (SFR-) Always Below 1 Ω




d.

Check for a short to ground in the circuit.

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
NW2-1 (SFR+) - Body ground Always 1 MΩ or higher
NW2-2 (SFR-) - Body ground Always 1 MΩ or higher




e.

Check for a short in the circuit.

i.

Release the activation prevention mechanism built into connector B (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DIAGNOSIS SYSTEM).


ii.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
NW2-1 (SFR+) - NW2-2 (SFR-) Always 1 MΩ or higher



iii.

Restore the released activation prevention mechanism of connector B to the original condition.

Text in Illustration
*1 Front Seat Side Airbag Assembly RH
*2 Center Airbag Sensor Assembly
*3 Front Seat Wire RH
*4 No. 2 Floor Wire
*a Front view of wire harness connector
(to Front Seat Wire RH)




OK

6.CHECK FRONT SEAT WIRE RH

NG

REPLACE NO. 2 FLOOR WIRE

6.CHECK FRONT SEAT WIRE RH
a.

Check for a short to B+ in the circuit.

i.
U189599E02
0.323,0.823 0.323,0.354 0.323,0.354 0.583,0.354 false 1.771,2.646 2.021,2.646 true 1.198,2.646 1.448,2.646 true 1.781,0.823 1.781,0.354 1.781,0.354 1.938,0.354 false 1.021,0.958 1.021,1.333 1.021,1.333 1.198,1.333 false 0.594,0.271 0.75,0.427 0.156,0.156 10 false *1 2.656,0.521 2.833,0.677 0.177,0.156 10 false *2 2.26,0.802 2.375,0.958 0.115,0.156 10 false A 1.948,0.802 2.063,0.958 0.115,0.156 10 false B 1.49,0.802 1.615,0.958 0.125,0.156 10 false C 1.177,0.802 1.302,0.958 0.125,0.156 10 false D 0.75,0.802 0.875,0.958 0.125,0.156 10 false E 0.427,0.802 0.552,0.958 0.125,0.156 10 false F 0.302,1.792 0.469,1.958 0.167,0.167 10 false *a 0.531,2.125 0.844,2.292 0.313,0.167 10 false We1 2.052,2.552 2.406,2.708 0.354,0.156 10 false SFR- 0.729,2.552 1.146,2.74 0.417,0.188 10 false SFR+ 1.958,0.271 2.115,0.427 0.156,0.156 10 false *4 1.219,1.24 1.365,1.396 0.146,0.156 10 false *3

Connect the cable to the negative (-) battery terminal.


ii.

Turn the engine switch on (IG).


iii.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
We1-1 (SFR+) - Body ground Engine switch on (IG) Below 1 V
We1-2 (SFR-) - Body ground Engine switch on (IG) Below 1 V



iv.

Turn the engine switch off.


v.

Disconnect the cable from the negative (-) battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.




b.

Check for an open in the circuit.

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
We1-1 (SFR+) - We1-2 (SFR-) Always Below 1 Ω




c.

Check for a short to ground in the circuit.

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
We1-1 (SFR+) - Body ground Always 1 MΩ or higher
We1-2 (SFR-) - Body ground Always 1 MΩ or higher




d.

Check for a short in the circuit.

i.

Release the activation prevention mechanism built into connector D (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DIAGNOSIS SYSTEM).


ii.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
We1-1 (SFR+) - We1-2 (SFR-) Always 1 MΩ or higher



iii.

Restore the released activation prevention mechanism of connector D to the original condition.

Text in Illustration
*1 Front Seat Side Airbag Assembly RH
*2 Center Airbag Sensor Assembly
*3 Front Seat Wire RH
*4 No. 2 Floor Wire
*a Front view of wire harness connector
(to Front Seat Side Airbag Assembly RH)




OK

NG

REPLACE FRONT SEAT WIRE RH