Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › AIRBAG SYSTEM › from 2016.05
RM24M0E _58 Vehicle Interior _059562 SUPPLEMENTAL RESTRAINT SYSTEMS _0291898 AIRBAG SYSTEM C

SUPPLEMENTAL RESTRAINT SYSTEMS  AIRBAG SYSTEM  B1825/56  Short in Side Squib LH Circuit  B1826/56  Open in Side Squib LH Circuit  B1827/56  Short to GND in Side Squib LH Circuit  B1828/56  Short to B+ in Side Squib LH Circuit  


DESCRIPTION

The side squib LH circuit consists of the center airbag sensor assembly and the front seat side airbag assembly LH.

The center airbag sensor assembly uses this circuit to deploy the airbag when deployment conditions are met.

These DTCs are stored when a malfunction is detected in the side squib LH circuit.

DTC No. DTC Detection Condition Trouble Area
B1825/56
·

The center airbag sensor assembly detects a line short in the side squib LH circuit during the primary check.

·

Side squib LH malfunction

·

Center airbag sensor assembly malfunction


·

Floor wire

·

Front seat wire LH

·

Front seat side airbag assembly LH (Side squib LH)

·

Center airbag sensor assembly


B1826/56
·

The center airbag sensor assembly detects an open in the side squib LH circuit.

·

Side squib LH malfunction

·

Center airbag sensor assembly malfunction


B1827/56
·

The center airbag sensor assembly detects a short to ground in the side squib LH circuit.

·

Side squib LH malfunction

·

Center airbag sensor assembly malfunction


B1828/56
·

The center airbag sensor assembly detects a short to B+ in the side squib LH circuit.

·

Side squib LH malfunction

·

Center airbag sensor assembly malfunction



WIRING DIAGRAM

C351803E15
0.708,2.5 1.5,2.885 0.792,0.385 10 false Xf1 0.708,2.656 3.125,3.125 2.417,0.469 10 false Front Seat Side Airbag Assembly LH (Side Squib LH) 2,1.906 2.792,2.292 0.792,0.385 10 false SFL- 2,1.073 2.792,1.458 0.792,0.385 10 false SFL+ 2.406,1.052 3.198,1.438 0.792,0.385 10 false 1 2.406,1.885 3.198,2.271 0.792,0.385 10 false 2 3.375,1.167 4.167,1.552 0.792,0.385 10 false MX2 4.5,1.042 5.292,1.427 0.792,0.385 10 false 9 4.448,1.885 5.24,2.271 0.792,0.385 10 false 10 4.708,3.188 6.677,3.469 1.969,0.281 10 false Center Airbag Sensor Assembly 4.719,3.021 5.51,3.406 0.792,0.385 10 false M9 3.375,2 4.167,2.385 0.792,0.385 10 false MX2 4.708,1.156 5.5,1.542 0.792,0.385 10 false SFL+ 4.688,2 5.479,2.385 0.792,0.385 10 false SFL- 3.417,0.969 4.208,1.354 0.792,0.385 10 false 1 3.448,1.813 4.24,2.198 0.792,0.385 10 false 2

CAUTION / NOTICE / HINT

NOTICE:

After turning the engine switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).


HINT:
·

Perform the simulation method by selecting check mode (Signal Check) using the intelligent tester (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>CHECK MODE PROCEDURE).

·

After selecting check mode (Signal Check), perform the simulation method by wiggling each connector of the airbag system or driving the vehicle on a city road or rough road (See page General>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING).



PROCEDURE

1.CHECK CONNECTORS
a.
C238337E05
0.191,1.557 0.347,1.709 0.156,0.152 10 *1 0.622,0.516 0.789,0.682 0.167,0.165 10 *3 2.713,0.956 2.887,1.112 0.174,0.156 10 *2 2.261,0.956 2.378,1.109 0.117,0.153 10 A 1.95,0.956 2.067,1.109 0.117,0.153 10 B 1.47,0.956 1.597,1.109 0.127,0.153 10 C 1.16,0.956 1.287,1.109 0.127,0.153 10 D 0.685,0.956 0.812,1.109 0.127,0.153 10 E 0.388,0.956 0.515,1.109 0.127,0.153 10 F 0.274,1.11 0.274,1.544 false 1.698,1.557 1.854,1.709 0.156,0.152 10 *4 1.781,1.11 1.781,1.544 false 0.982,0.978 0.982,0.605 0.982,0.605 0.818,0.605 false

Turn the engine switch off.


b.

Disconnect the cable from the negative (-) battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.



c.

Check that the connectors are properly connected to the front seat side airbag assembly LH and center airbag sensor assembly. Also check that the connectors that link the front seat wire LH and floor wire are properly connected.

OK:

The connectors are properly connected.


HINT:

If the connectors are not properly connected, reconnect the connectors and proceed to the next inspection.



d.

Disconnect the connectors from the front seat side airbag assembly LH and center airbag sensor assembly. Also disconnect the floor wire from the front seat wire LH.


e.

Check that the terminals of the connectors are not deformed or damaged.

OK:

The terminals are not deformed or damaged.



f.

Check that the short springs of the activation prevention mechanisms of the floor wire connector and front seat wire LH connector are not deformed or damaged.

OK:

The short springs are not deformed or damaged.


Text in Illustration
*1 Front Seat Side Airbag Assembly LH
*2 Center Airbag Sensor Assembly
*3 Front Seat Wire LH
*4 Floor Wire



OK

2.CHECK FRONT SEAT SIDE AIRBAG ASSEMBLY LH

NG

REPLACE WIRE HARNESS

2.CHECK FRONT SEAT SIDE AIRBAG ASSEMBLY LH
a.
U189604E01
0.319,1.597 0.487,1.762 0.167,0.165 10 *a 2.282,2.269 2.593,2.420 0.310,0.151 10 SST 2.034,2.356 2.25,2.356 false 0.307,1.099 0.463,1.250 0.156,0.152 10 *1 2.59,0.679 2.764,0.835 0.174,0.156 10 *2 2.172,0.679 2.289,0.832 0.117,0.153 10 A 2.016,0.679 2.132,0.832 0.117,0.153 10 B 1.526,0.679 1.653,0.832 0.127,0.153 10 C 1.369,0.679 1.496,0.832 0.127,0.153 10 D 0.892,0.679 1.019,0.832 0.127,0.153 10 E 0.494,0.679 0.621,0.832 0.127,0.153 10 F 0.39,0.826 0.39,1.085 false 0.506,2.103 0.772,2.259 0.266,0.156 10 Xf1

Connect the floor wire to the front seat wire LH and center airbag sensor assembly.


b.

Connect SST (resistance 2.1 Ω) to connector E.

CAUTION:

Never connect a tester to the front seat side airbag assembly LH for measurement, as this may lead to a serious injury due to airbag deployment.


NOTICE:
·

Do not forcibly insert SST into the terminals of the connector when connecting it.

·

Insert SST straight into the terminals of the connector.




SST
09843-18061  

c.

Connect the cable to the negative (-) battery terminal.



e.

Turn the engine switch off.


f.

Turn the engine switch on (IG), and wait for at least 60 seconds.


g.

Check for DTCs (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR).

OK:

DTC B1825/56, B1826/56, B1827/56 or B1828/56 is not output.


Result:
Result Proceed to
OK (for Manual Seat) A
OK (for Power Seat) B
NG C


HINT:

Codes other than DTCs B1825/56, B1826/56, B1827/56 and B1828/56 may be output at this time, but they are not related to this check.



h.

Turn the engine switch off.


i.

Disconnect the cable from the negative (-) battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.



j.

Disconnect SST from connector E.

Text in Illustration
*1 Front Seat Side Airbag Assembly LH
*2 Center Airbag Sensor Assembly
*a Front view of wire harness connector
(to Front Seat Side Airbag Assembly LH)



A

REPLACE FRONT SEAT SIDE AIRBAG ASSEMBLY LH (FRONT SEAT ASSEMBLY LH)

B

REPLACE FRONT SEAT SIDE AIRBAG ASSEMBLY LH (FRONT SEAT ASSEMBLY LH)

C

3.CHECK SIDE SQUIB LH CIRCUIT
3.CHECK SIDE SQUIB LH CIRCUIT
a.
U189594E02
0.385,0.75 0.385,1.01 false 1.458,2.635 1.146,2.635 true 2.073,2.635 1.76,2.635 true 0.281,1.771 0.448,1.938 0.167,0.167 10 false *a 0.302,1.031 0.458,1.188 0.156,0.156 10 false *1 2.594,0.604 2.771,0.76 0.177,0.156 10 false *2 2.177,0.604 2.292,0.76 0.115,0.156 10 false A 1.854,0.604 1.969,0.76 0.115,0.156 10 false B 1.406,0.604 1.531,0.76 0.125,0.156 10 false C 1.25,0.604 1.375,0.76 0.125,0.156 10 false D 0.802,0.604 0.927,0.76 0.125,0.156 10 false E 0.49,0.604 0.615,0.76 0.125,0.156 10 false F 0.646,2.104 0.917,2.26 0.271,0.156 10 false Xf1 0.688,2.542 1.063,2.698 0.375,0.156 10 false SFL+ 2.104,2.542 2.479,2.698 0.375,0.156 10 false SFL-

Disconnect the floor wire from the center airbag sensor assembly.


b.

Check for a short to B+ in the circuit.

i.

Connect the cable to the negative (-) battery terminal.


ii.

Turn the engine switch on (IG).


iii.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
Xf1-1 (SFL+) - Body ground Engine switch on (IG) Below 1 V
Xf1-2 (SFL-) - Body ground Engine switch on (IG) Below 1 V



iv.

Turn the engine switch off.


v.

Disconnect the cable from the negative (-) battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.




c.

Check for an open in the circuit.

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
Xf1-1 (SFL+) - Xf1-2 (SFL-) Always Below 1 Ω




d.

Check for a short to ground in the circuit.

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
Xf1-1 (SFL+) - Body ground Always 1 MΩ or higher
Xf1-2 (SFL-) - Body ground Always 1 MΩ or higher




e.

Check for a short in the circuit.

i.

Release the activation prevention mechanism built into connector B (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DIAGNOSIS SYSTEM).


ii.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
Xf1-1 (SFL+) - Xf1-2 (SFL-) Always 1 MΩ or higher



iii.

Restore the released activation prevention mechanism of connector B to the original condition.

Text in Illustration
*1 Front Seat Side Airbag Assembly LH
*2 Center Airbag Sensor Assembly
*a Front view of wire harness connector
(to Front Seat Side Airbag Assembly LH)




OK

4.CHECK DTC

NG

5.CHECK FLOOR WIRE
4.CHECK DTC
a.
C238340E01
0.56,0.937 0.669,1.090 0.109,0.153 10 F 0.713,0.937 0.834,1.090 0.121,0.153 10 E 1.232,0.937 1.353,1.090 0.121,0.153 10 D 1.389,0.937 1.510,1.090 0.121,0.153 10 C 1.917,0.937 2.037,1.090 0.121,0.153 10 B 2.07,0.937 2.191,1.090 0.121,0.153 10 A 0.363,1.379 0.515,1.554 0.152,0.175 10 *1 2.499,0.937 2.675,1.081 0.176,0.144 10 *2 0.448,1.084 0.448,1.37 false

Connect the connectors to the front seat side airbag assembly LH and the center airbag sensor assembly.


b.

Connect the cable to the negative (-) battery terminal.



d.

Turn the engine switch off.


e.

Turn the engine switch on (IG), and wait for at least 60 seconds.


f.

Check for DTCs (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR).

OK:

DTC B1825/56, B1826/56, B1827/56 or B1828/56 is not output.


HINT:

Codes other than DTCs B1825/56, B1826/56, B1827/56 and B1828/56 may be output at this time, but they are not related to this check.


Text in Illustration
*1 Front Seat Side Airbag Assembly LH
*2 Center Airbag Sensor Assembly



OK

NG

5.CHECK FLOOR WIRE
a.
U189595E02
0.323,0.771 0.323,1.031 false 1.01,0.771 1.01,1.031 false 1.781,0.625 1.781,0.24 1.781,0.24 1.594,0.24 false 1.448,2.667 1.135,2.667 true 2.073,2.667 1.76,2.667 true 0.281,1.771 0.448,1.938 0.167,0.167 10 false *a 0.24,1.052 0.396,1.208 0.156,0.156 10 false *1 2.677,0.625 2.854,0.781 0.177,0.156 10 false *2 2.26,0.625 2.375,0.781 0.115,0.156 10 false A 1.948,0.625 2.063,0.781 0.115,0.156 10 false B 1.49,0.625 1.615,0.781 0.125,0.156 10 false C 1.177,0.625 1.302,0.781 0.125,0.156 10 false D 0.74,0.625 0.865,0.781 0.125,0.156 10 false E 0.427,0.625 0.552,0.781 0.125,0.156 10 false F 0.927,1.052 1.083,1.208 0.156,0.156 10 false *3 0.531,2.115 0.844,2.271 0.313,0.156 10 false MX2 1.406,0.156 1.563,0.313 0.156,0.156 10 false *4 0.677,2.573 1.094,2.76 0.417,0.188 10 false SFL+ 2.094,2.573 2.5,2.771 0.406,0.198 10 false SFL-

Disconnect the front seat wire LH from the floor wire.


b.

Check for a short to B+ in the circuit.

i.

Connect the cable to the negative (-) battery terminal.


ii.

Turn the engine switch on (IG).


iii.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
MX2-1 (SFL+) - Body ground Engine switch on (IG) Below 1 V
MX2-2 (SFL-) - Body ground Engine switch on (IG) Below 1 V



iv.

Turn the engine switch off.


v.

Disconnect the cable from the negative (-) battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.




c.

Check for an open in the circuit.

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
MX2-1 (SFL+) - MX2-2 (SFL-) Always Below 1 Ω




d.

Check for a short to ground in the circuit.

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
MX2-1 (SFL+) - Body ground Always 1 MΩ or higher
MX2-2 (SFL-) - Body ground Always 1 MΩ or higher




e.

Check for a short in the circuit.

i.

Release the activation prevention mechanism built into connector B (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DIAGNOSIS SYSTEM).


ii.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
MX2-1 (SFL+) - MX2-2 (SFL-) Always 1 MΩ or higher



iii.

Restore the released activation prevention mechanism of connector B to the original condition.

Text in Illustration
*1 Front Seat Side Airbag Assembly LH
*2 Center Airbag Sensor Assembly
*3 Front Seat Wire LH
*4 Floor Wire
*a Front view of wire harness connector
(to Front Seat Wire LH)




OK

6.CHECK FRONT SEAT WIRE LH

NG

REPLACE FLOOR WIRE

6.CHECK FRONT SEAT WIRE LH
a.
U189596E02
0.323,0.76 0.323,1.021 false 1.771,2.646 2.01,2.646 true 1.219,2.646 1.448,2.646 true 1.01,0.615 1.01,0.271 1.01,0.271 0.844,0.271 false 1.771,0.76 1.771,1.125 false 0.271,1.75 0.438,1.917 0.167,0.167 10 false *a 0.24,1.042 0.396,1.198 0.156,0.156 10 false *1 2.677,0.604 2.854,0.76 0.177,0.156 10 false *2 2.26,0.604 2.375,0.76 0.115,0.156 10 false A 1.938,0.604 2.052,0.76 0.115,0.156 10 false B 1.49,0.604 1.615,0.76 0.125,0.156 10 false C 1.177,0.604 1.302,0.76 0.125,0.156 10 false D 0.729,0.604 0.854,0.76 0.125,0.156 10 false E 0.427,0.604 0.552,0.76 0.125,0.156 10 false F 0.625,2.083 0.896,2.24 0.271,0.156 10 false Xf1 2.042,2.563 2.385,2.708 0.344,0.146 10 false SFL- 0.76,2.563 1.146,2.708 0.385,0.146 10 false SFL+ 0.667,0.198 0.823,0.354 0.156,0.156 10 false *3 1.688,1.125 1.844,1.281 0.156,0.156 10 false *4

Check for a short to B+ in the circuit.

i.

Connect the cable to the negative (-) battery terminal.


ii.

Turn the engine switch on (IG).


iii.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
Xf1-1 (SFL+) - Body ground Engine switch on (IG) Below 1 V
Xf1-2 (SFL-) - Body ground Engine switch on (IG) Below 1 V



iv.

Turn the engine switch off.


v.

Disconnect the cable from the negative (-) battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.




b.

Check for an open in the circuit.

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
Xf1-1 (SFL+) - Xf1-2 (SFL-) Always Below 1 Ω




c.

Check for a short to ground in the circuit.

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
Xf1-1 (SFL+) - Body ground Always 1 MΩ or higher
Xf1-2 (SFL-) - Body ground Always 1 MΩ or higher




d.

Check for a short in the circuit.

i.

Release the activation prevention mechanism built into connector D (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DIAGNOSIS SYSTEM).


ii.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
Xf1-1 (SFL+) - Xf1-2 (SFL-) Always 1 MΩ or higher



iii.

Restore the released activation prevention mechanism of connector D to the original condition.

Text in Illustration
*1 Front Seat Side Airbag Assembly LH
*2 Center Airbag Sensor Assembly
*3 Front Seat Wire LH
*4 Floor Wire
*a Front view of wire harness connector
(to Front Seat Side Airbag Assembly LH)




OK

NG

REPLACE FRONT SEAT WIRE LH