Home › Drivetrain › U241E (AUTOMATIC TRANSMISSION / TRANSAXLE) › AUTOMATIC TRANSAXLE ASSEMBLY › from 2014.09
RM24M0E _52 Drivetrain _059578 U241E AUTOMATIC TRANSMISSION / TRANSAXLE _0292105 AUTOMATIC TRANSAXLE ASSEMBLY A

U241E AUTOMATIC TRANSMISSION / TRANSAXLE  AUTOMATIC TRANSAXLE ASSEMBLY  INSTALLATION  


PROCEDURE

Hide 32000 1.INSPECT TORQUE CONVERTER ASSEMBLY

Hide 32000 2.INSTALL TORQUE CONVERTER ASSEMBLY

a.
D025371E14
2.302,0.156 2.219,0.156 2.219,0.156 1.865,0.615 false 3.073,0.917 3.271,1.115 0.198,0.198 10 false *a 2.344,0.042 2.542,0.24 0.198,0.198 10 false *b

Turn the front oil pump drive gear so that the key is at the top and place a matchmark on the transaxle housing to indicate the position of the key.

Text in Illustration
*a Key
*b Matchmark


b.
C057914E11
1.406,1.979 1.583,1.979 1.583,1.979 1.75,1.552 true 1.698,0.344 1.302,0.167 1.302,0.167 1.177,0.167 true 1.01,0.083 1.323,0.24 0.313,0.156 10 false *a 1.229,1.917 1.542,2.073 0.313,0.156 10 false *b

Place a matchmark on the torque converter assembly so that the position of its groove is clearly indicated.

Text in Illustration
*a Groove
*b Matchmark


c.
C310693E02
1.167,0.5 0.771,0.219 0.771,0.219 1.167,0.667 true 2.406,0.792 1.729,1.823 1.729,1.823 2.417,1.094 true 1.563,1.792 1.76,1.99 0.198,0.198 10 false *1 0.615,0.073 0.813,0.271 0.198,0.198 10 false *a

Align the matchmark on the transaxle housing with the one on the torque converter assembly and engage the splines of the input shaft with the turbine runner splines.

Text in Illustration
*1 Front Oil Pump Oil Seal
*a Matchmark

NOTICE:
·

Install the torque converter assembly to the input shaft while keeping it horizontal.

·

Do not damage the front oil pump oil seal.




d.
C310694E02
1.167,0.5 0.99,0.26 0.99,0.26 0.885,0.26 true 2.396,0.823 1.708,1.854 1.708,1.854 2.417,1.115 true 1.167,1.469 0.99,1.938 0.99,1.938 0.885,1.938 true 1.542,1.823 1.74,2.01 0.198,0.188 10 false *1 0.719,0.167 0.917,0.354 0.198,0.188 10 false *a 0.698,1.844 0.896,2.031 0.198,0.188 10 false *a

Rotate the torque converter assembly approximately 180° and engage the splines of the stator shaft with the stator assembly.

Text in Illustration
*1 Front Oil Pump Oil Seal
*a Matchmark

NOTICE:
·

Install the torque converter assembly to the input shaft while keeping it horizontal.

·

Do not damage the front oil pump oil seal.




e.
C310695E02
2.406,0.823 1.698,1.917 1.698,1.917 2.406,1.115 true 1.167,0.51 0.781,0.219 0.781,0.219 1.167,0.656 true 1.521,1.865 1.719,2.052 0.198,0.188 10 false *1 0.604,0.094 0.813,0.281 0.208,0.188 10 false *a

Rotate the torque converter assembly approximately 180° again, align the matchmark on the torque converter assembly with the one on the housing and insert the groove of the torque converter assembly into the key of the oil pump drive gear.

Text in Illustration
*1 Front Oil Pump Oil Seal
*a Matchmark

NOTICE:
·

Do not push the torque converter assembly excessively when rotating it.

·

Install the torque converter assembly to the input shaft while keeping it horizontal.

·

Do not damage the front oil pump oil seal.




f.

Clean the drive plate and torque converter assembly setting bolt holes.


g.
C202919E09
0.144,0.184 0.347,0.349 0.203,0.165 10 *a 0.348,0.271 0.451,0.271 0.451,0.271 0.635,0.718 false 2.532,1.47 2.735,1.635 0.203,0.165 10 *a 2.419,0.671 2.557,0.836 0.138,0.165 10 A 2.599,2.025 2.761,2.19 0.162,0.165 10 *b 1.378,2.303 1.378,3.035 false 1.289,3.054 1.451,3.219 0.162,0.165 10 *b 2.62,1.2 2.62,1.457 false 2.85,1.765 2.687,1.927 2.687,1.927 2.687,2.027 false

Using a vernier caliper and straightedge, measure the dimension (A) between the automatic transaxle assembly contact surface of the engine assembly*a and the torque converter assembly contact surfaces of the drive plate*b.

Text in Illustration
*a Engine Assembly Surface
*b Drive Plate Surface


h.
C315703E01
2.73,0.124 2.895,0.312 0.165,0.188 10 B

Using a vernier caliper and straightedge, measure the dimension (B) shown in the illustration and check that the dimension (B) is more than the dimension (A), which was measured in the previous step.

Standard:

Dimension (A) + 1.0 mm (0.0394 in.) or more


NOTICE:
·

Make sure to deduct the thickness of the straightedge.

·

If the automatic transaxle assembly is installed to the engine assembly with the torque converter assembly not sufficiently inserted, the torque converter assembly may be damaged.

·

Do not include the thickness of the set block.




Hide 33823 3.INSTALL NO. 1 TRANSMISSION CONTROL CABLE BRACKET

a.

Install the No. 1 transmission control cable bracket to the automatic transaxle assembly with the 2 bolts.

Torque:
12 N*m (122 kgf*cm, 9 ft.*lbf)


Hide 35013 4.INSTALL TRANSMISSION OIL FILLER TUBE SUB-ASSEMBLY

a.

Coat a new O-ring with ATF and install it to the transmission oil filler tube sub-assembly.

NOTICE:

Be careful not to damage the O-ring.



b.

Install the transmission oil filler tube sub-assembly to the automatic transaxle assembly with the bolt.

Torque:
5.5 N*m (56 kgf*cm, 49 in.*lbf)


c.

Install the transmission oil level gauge sub-assembly to the transmission oil filler tube sub-assembly.


Hide 30500 5.INSTALL AUTOMATIC TRANSAXLE ASSEMBLY

a.
C310696E02
1.615,0.906 1.917,0.583 true 1.917,0.583 2.594,0.583 true 0.896,1.042 1.208,1.24 0.313,0.198 10 false *1 2.635,0.49 2.948,0.688 0.313,0.198 10 false *a

Apply clutch spline grease to the surface of the crankshaft that contacts the torque converter assembly centerpiece.

Text in Illustration
*1 Crankshaft
*a Torque Converter Assembly Centerpiece

Clutch Spline Grease:

Toyota Genuine Clutch Spline Grease or equivalent


Maximum Grease Amount:

Approximately 1 g (0.0353 oz)



b.
C193868E05
0.823,2.292 0.948,2.438 0.125,0.146 10 false A 1.896,2.281 2.021,2.448 0.125,0.167 10 false A 0.354,3.01 0.479,3.177 0.125,0.167 10 false A 0.25,3.615 0.375,3.781 0.125,0.167 10 false B 2.417,2.75 2.542,2.917 0.125,0.167 10 false B

Confirm that the 2 knock pins are installed on the engine assembly and are not damaged.


c.

Install the automatic transaxle assembly to the engine assembly with the 5 bolts.

Torque:
64 N*m (653 kgf*cm, 47 ft.*lbf)

for bolt (A)

46 N*m (469 kgf*cm, 34 ft.*lbf)

for bolt (B)


NOTICE:
·

Make sure that the wire harness or similar items are not pinched between the contact surfaces.

·

Do not use excess force when installing the automatic transaxle assembly.

·

When mounting the automatic transaxle assembly to the engine assembly, make sure to securely fit the 2 knock pins into the knock holes.

·

Check that the torque converter assembly rotates.

·

When tightening the bolts, be sure that the mating surfaces of the engine assembly and the automatic transaxle assembly are in close contact with one another.




d.

Install the 4 bolts.

Torque:
37 N*m (377 kgf*cm, 27 ft.*lbf)


Hide 32101A 6.INSTALL DRIVE PLATE AND TORQUE CONVERTER ASSEMBLY SETTING BOLT

a.

Clean the threads of the 6 drive plate and torque converter assembly setting bolts.


b.
C296562E02
1.987,1.357 1.584,1.76 1.584,1.76 1.811,1.76 false 1.867,1.688 2.582,1.900 0.715,0.211 10 *a

Apply a few drops of adhesive to 2 or 3 threads at the tip of each of the 6 drive plate and torque converter assembly setting bolts.

Text in Illustration
*a Adhesive

Adhesive:

Toyota Genuine Adhesive 1324, Three Bond 1324 or equivalent


NOTICE:

In order to ensure proper installation of the 6 drive plate and torque converter assembly setting bolts, apply adhesive to the 6 drive plate and torque converter assembly setting bolts and install them within 10 minutes of adhesive application.



c.

Turn the crankshaft to gain access to the installation locations of the 6 drive plate and torque converter assembly setting bolts and install each bolt while holding the crankshaft pulley with SST.

SST
09213-54015  (91651-60855)
09330-00021  

Torque:
41 N*m (418 kgf*cm, 30 ft.*lbf)

NOTICE:

First install the black-colored bolt, and then the remaining 5 silver-colored bolts.



Hide 11361J 7.INSTALL FLYWHEEL HOUSING UNDER COVER

a.

Install the flywheel housing under cover to the engine assembly.


Hide 12325A 8.INSTALL ENGINE MOUNTING BRACKET LH

a.

Install the engine mounting bracket LH to the automatic transaxle assembly with the 3 bolts.

Torque:
64 N*m (653 kgf*cm, 47 ft.*lbf)


Hide 12311A 9.INSTALL FRONT ENGINE MOUNTING BRACKET

a.

Install the front engine mounting bracket to the automatic transaxle assembly with the 3 bolts.

Torque:
64 N*m (653 kgf*cm, 47 ft.*lbf)


Hide 12321A 10.INSTALL REAR ENGINE MOUNTING BRACKET

a.

Install the rear engine mounting bracket to the automatic transaxle assembly with the 3 bolts.

Torque:
45 N*m (459 kgf*cm, 33 ft.*lbf)


Hide 12.CONNECT WIRE HARNESS

a.

Engage the 3 clamps.


b.

Connect the transmission wire connector.


c.

Connect the transmission revolution sensor NC connector.


d.

Connect the transmission revolution sensor NT connector.


e.

Connect the park/neutral position switch assembly connector.


Hide 28100 13.INSTALL STARTER ASSEMBLY

a.

Install the starter assembly to the automatic transaxle assembly with the 2 bolts.

Torque:
37 N*m (377 kgf*cm, 27 ft.*lbf)


b.

Connect the terminal with the nut.

Torque:
9.8 N*m (100 kgf*cm, 87 in.*lbf)


c.

Close the terminal cap.


d.

Connect the starter assembly connector.


Hide 14.INSTALL ENGINE ASSEMBLY WITH TRANSAXLE

a.

Install the engine assembly with transaxle (See page Engine / Hybrid System>2AZ-FE ENGINE MECHANICAL>ENGINE ASSEMBLY>INSTALLATION).


Hide 15.CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).


Hide 16.ADD AUTOMATIC TRANSAXLE FLUID

Fluid type:

Toyota Genuine ATF WS


Hide 17.INSPECT AUTOMATIC TRANSAXLE FLUID

Hide 18.PERFORM RESET MEMORY

a.

Perform the RESET MEMORY procedures (A/T initialization) (See page Drivetrain>U241E (AUTOMATIC TRANSMISSION / TRANSAXLE)>AUTOMATIC TRANSAXLE SYSTEM>INITIALIZATION).