Home › Suspension › SUSPENSION › FRONT LOWER SUSPENSION ARM(for 2GR-FE) › from 2016.05
RM24M0E _53 Suspension _059582 SUSPENSION _0292152 FRONT LOWER SUSPENSION ARM(for 2GR-FE) A

SUSPENSION  FRONT LOWER SUSPENSION ARM(for 2GR-FE)  INSTALLATION  


PROCEDURE

Hide 1.INSTALL FRONT SUSPENSION LOWER NO. 1 ARM SUB-ASSEMBLY

a.

Position the front suspension crossmember sub-assembly on a level surface.

C135554E05
0.208,0.5 0.208,0.792 true 1.073,1.521 1.354,1.521 false 0.76,0.375 1.073,0.375 true 1.375,1.438 1.583,1.635 0.208,0.198 10 false *1 1.104,0.302 1.302,0.458 0.198,0.156 10 false *2 0.146,0.802 0.365,0.979 0.219,0.177 10 false *3 4.948,1.531 5.156,1.729 0.208,0.198 10 false *1 3.292,1.188 3.458,1.354 0.167,0.167 10 true *2 2.563,1.344 2.74,1.521 0.177,0.177 10 true *3 5.375,1.417 5.542,1.583 0.167,0.167 10 false A 6.729,1.25 6.885,1.438 0.156,0.188 10 true B

NOTICE:

Position the crossmember with the front suspension member brace front LH and RH mounted.



b.

Using vernier calipers, measure height*1 and *2.


c.

Check that height*2 is lower than *1 by 10 mm.


d.

Position the front suspension lower No. 1 arm so that height*3 is the same as *1.


e.

Tighten the bolt A.

Torque:
233 N*m (2376 kgf*cm, 172 ft.*lbf)


f.

Temporarily install the bolt and nut.


Hide 51201 2.INSTALL FRONT SUSPENSION CROSSMEMBER SUB-ASSEMBLY

a.

Raise the front suspension crossmember sub-assembly with a transmission jack.


b.
C135506E02
1.656,0.563 1.771,0.708 0.115,0.146 10 true B 1.99,0.552 2.104,0.698 0.115,0.146 10 true B 0.375,0.896 0.49,1.042 0.115,0.146 10 true A 2.969,0.885 3.083,1.031 0.115,0.146 10 true A

Temporarily install the front suspension crossmember sub-assembly with 2 bolts A, the 2 bolts B and 2 nuts.


c.
C135505E03
1.573,0.458 1.688,0.604 0.115,0.146 10 true A 1.01,1.75 1.125,1.896 0.115,0.146 10 true B 1.938,1.75 2.052,1.896 0.115,0.146 10 true B

Temporarily install the front suspension member brace sub-assembly LH and RH with 2 bolts A and the 4 bolts B.


d.

Alternately insert SST into the reference holes on the front suspension crossmember RH and LH while tightening bolts A and B on the LH and RH sides to each specified torque in several steps.

SST
09670-00010  

C160367E07
2.604,3.656 2.365,3.656 true 4.604,3.667 4.885,3.667 true 3.042,0.052 4.333,0.229 1.292,0.177 10 false Front of the Vehicle 0.792,2.094 0.979,2.281 0.188,0.188 10 false A 6.281,2.052 6.479,2.229 0.198,0.177 10 false A 2.677,3.24 2.823,3.427 0.146,0.188 10 true A 4.417,3.24 4.552,3.417 0.135,0.177 10 true A 1.271,3.594 1.385,3.74 0.115,0.146 10 true B 2.438,3.104 2.552,3.25 0.115,0.146 10 true B 5.781,3.625 5.896,3.771 0.115,0.146 10 true B 4.75,3.083 4.865,3.229 0.115,0.146 10 true B 1.229,5.406 1.51,5.563 0.281,0.156 10 false OK 2.083,5.396 2.323,5.563 0.24,0.167 10 false NG 4.677,5.406 4.958,5.563 0.281,0.156 10 false OK 5.521,5.396 5.76,5.563 0.24,0.167 10 false NG 2.646,3.573 3.01,3.729 0.365,0.156 10 true SST 4.323,3.583 4.615,3.75 0.292,0.167 10 true SST

Torque:
Bolt A : 137 N*m (1397 kgf*cm, 101 ft.*lbf)
Bolt B : 93 N*m (948 kgf*cm, 69 ft.*lbf)


e.
C135508

Fully tighten the 2 bolts and 2 nuts.

Torque:
96 N*m (978 kgf*cm, 71 ft.*lbf)


Hide 48069 3.CONNECT FRONT SUSPENSION LOWER NO. 1 ARM SUB-ASSEMBLY LH

a.
C135504

Connect the front suspension lower No. 1 arm LH to the ball joint with the bolt and 2 nuts.

Torque:
93 N*m (948 kgf*cm, 69 ft.*lbf)


Hide 48068 4.CONNECT FRONT SUSPENSION LOWER NO. 1 ARM SUB-ASSEMBLY RH

HINT:

Perform the same procedures as for the LH side.


Hide 5.CONNECT TIE ROD END SUB-ASSEMBLY LH

Hide 6.CONNECT TIE ROD END SUB-ASSEMBLY RH

HINT:

Perform the same procedures as for the LH side.


Hide 45260 7.CONNECT NO. 2 STEERING INTERMEDIATE SHAFT ASSEMBLY (for LHD)

Hide 45260 8.CONNECT NO. 2 STEERING INTERMEDIATE SHAFT ASSEMBLY (for RHD)

Hide 45259A 9.INSTALL COLUMN HOLE COVER SILENCER SHEET (for LHD)

Hide 45259A 10.INSTALL COLUMN HOLE COVER SILENCER SHEET (for RHD)

Hide 51218A 11.INSTALL FRONT SUSPENSION MEMBER REINFORCEMENT LH

a.
C135503

Install the front suspension member reinforcement LH with the 4 bolts.

Torque:
96 N*m (979 kgf*cm, 71 ft.*lbf)


Hide 51217A 12.INSTALL FRONT SUSPENSION MEMBER REINFORCEMENT RH

HINT:

Perform the same procedures as for the LH side.


Hide 48810 13.INSTALL FRONT STABILIZER LINK ASSEMBLY LH

a.
C149506

Install the front stabilizer link assembly LH to the front stabilizer bar with the nut.

Torque:
74 N*m (755 kgf*cm, 55 ft.*lbf)

HINT:

If the ball joint turns together with the nut, use a hexagon wrench (6 mm) to hold the stud bolt.



Hide 48820B 14.INSTALL FRONT STABILIZER LINK ASSEMBLY RH

HINT:

Perform the same procedures as for the LH side.


Hide 53702 15.INSTALL FRONT FENDER APRON SUB-ASSEMBLY LH

Hide 53701 16.INSTALL FRONT FENDER APRON SUB-ASSEMBLY RH

Hide 51441D 17.INSTALL ENGINE UNDER COVER

Hide 51442 18.INSTALL NO. 2 ENGINE UNDER COVER

Hide 51441 19.INSTALL NO. 1 ENGINE UNDER COVER

Hide 20.INSTALL FRONT WHEEL

Torque:
103 N*m (1050 kgf*cm, 76 ft.*lbf)

Hide 22.FULLY TIGHTEN FRONT SUSPENSION LOWER NO. 1 ARM SUB-ASSEMBLY

a.
C138701

Fully tighten the bolt.

Torque:
214 N*m (2182 kgf*cm, 158 ft.*lbf)

NOTICE:

When removing the bolt, keep the nut from rotating.



Hide 23.INSPECT AND ADJUST FRONT WHEEL ALIGNMENT

a.

Inspect and adjust the front wheel alignment (See page Suspension>SUSPENSION>FRONT WHEEL ALIGNMENT>ADJUSTMENT).