Home › Steering › POWER STEERING › STEERING GEAR › from 2016.05
RM24M0E _55 Steering _059561 POWER STEERING _0291897 STEERING GEAR A

POWER STEERING  STEERING GEAR  INSTALLATION  


PROCEDURE

Hide 45510 1.INSTALL STEERING GEAR ASSEMBLY

a.
C138793

Install the steering gear onto the front suspension crossmember with the 2 bolts and 2 nuts.

Torque:
110 N*m (1122 kgf*cm, 81 ft.*lbf)

NOTICE:

Keep the nut from rotating while turning the bolt.



Hide 45221 2.INSTALL STEERING INTERMEDIATE SHAFT

a.
C138794E01
1.882,1.241 1.863,1.351 false 1.84,1.477 1.828,1.56 false 2.466,0.355 3.208,0.518 0.743,0.163 10 Matchmark 1.873,1.293 2.404,0.463 false 1.828,1.56 2.379,0.501 false

Align the matchmarks and install the intermediate shaft onto the steering gear.

Torque:
35 N*m (360 kgf*cm, 26 ft.*lbf)


Hide 45025D 3.INSTALL NO. 1 STEERING COLUMN HOLE COVER SUB-ASSEMBLY

a.

Install the column hole cover onto the steering gear with a new clamp.


b.
C128837E05
1.01,0.25 1.302,0.438 true 2.115,1.604 2.292,1.938 true 2.167,1.958 2.594,2.125 0.427,0.167 10 true Clip A 0.604,0.156 1.042,0.479 0.438,0.323 10 true Clip B

Attach clip B onto the body portion and install the No. 1 hole cover onto the body portion with clip A.

NOTICE:

Make sure that the lip portion of the No. 1 hole cover is not damaged.



Hide 51201 4.INSTALL FRONT SUSPENSION CROSSMEMBER SUB-ASSEMBLY (for 2AZ-FE)

Hide 51201 5.INSTALL FRONT SUSPENSION CROSSMEMBER SUB-ASSEMBLY (for 2GR-FE)

Hide 6.INSTALL FRONT AXLE ASSEMBLY LH

a.
C080293

Push down the front suspension lower arm, and install the front lower ball joint LH with the bolt and 2 nuts.

Torque:
93 N*m (948 kgf*cm, 69 ft.*lbf)


Hide 7.INSTALL FRONT AXLE ASSEMBLY RH

Hide 45407 8.INSTALL TIE ROD END SUB-ASSEMBLY LH

a.
C132132

Connect the tie rod end onto the steering knuckle with the castle nut.

Torque:
49 N*m (500 kgf*cm, 36 ft.*lbf)

NOTICE:

If the holes for the clip are not aligned, tighten the nut up to 60° further.



b.

Install a new cotter pin.


Hide 45046 9.INSTALL TIE ROD END SUB-ASSEMBLY RH

HINT:

Use the same procedure for the RH side as for the LH side.


Hide 48810 10.INSTALL FRONT STABILIZER LINK ASSEMBLY LH

Hide 48820B 11.INSTALL FRONT STABILIZER LINK ASSEMBLY RH

HINT:

Use the same procedure for the RH side as for the LH side.


Hide 51218A 12.INSTALL FRONT SUSPENSION MEMBER REINFORCEMENT LH

Hide 51217A 13.INSTALL FRONT SUSPENSION MEMBER REINFORCEMENT RH

HINT:

Use the same procedure for the RH side as for the LH side.


Hide 53702 14.INSTALL FRONT FENDER APRON LH

Hide 53701 15.INSTALL FRONT FENDER APRON RH

Hide 51441 16.INSTALL NO. 1 ENGINE UNDER COVER

Hide 51442 17.INSTALL NO. 2 ENGINE UNDER COVER

Hide 45260 18.INSTALL NO. 2 STEERING INTERMEDIATE SHAFT ASSEMBLY (for LHD)

Hide 45260 19.INSTALL NO. 2 STEERING INTERMEDIATE SHAFT ASSEMBLY (for RHD)

Hide 45259A 20.INSTALL COLUMN HOLE COVER SILENCER SHEET (for LHD)

Hide 45259A 21.INSTALL COLUMN HOLE COVER SILENCER SHEET (for RHD)

Hide 22.INSTALL FRONT WHEEL

Hide 28800 23.CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected (see page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).


Hide 24. PERFORM INITIALIZATION

NOTICE:

Certain systems need to be initialized after disconnecting and reconnecting the cable from the negative (-) battery terminal (see page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).


Hide 25.ADJUST FRONT WHEEL ALIGNMENT

a.

Adjust front wheel alignment (see page Suspension>SUSPENSION>FRONT WHEEL ALIGNMENT>ADJUSTMENT).