Home › Steering › STEERING COLUMN › STEERING COLUMN ASSEMBLY(for RHD) › from 2016.05
RM24M0E _55 Steering _059560 STEERING COLUMN _0291893 STEERING COLUMN ASSEMBLY(for RHD) A

STEERING COLUMN  STEERING COLUMN ASSEMBLY(for RHD)  INSTALLATION  


CAUTION / NOTICE / HINT

HINT:

A bolt without a torque specification is shown in the standard bolt chart (See page General>SPECIFICATIONS>STANDARD BOLT>SPECIFIED TORQUE FOR STANDARD BOLTS).


PROCEDURE

Hide 1.ALIGN FRONT WHEELS FACING STRAIGHT AHEAD

Hide 45260 2.INSTALL NO. 2 STEERING INTERMEDIATE SHAFT ASSEMBLY

a.
C136583E02
3.013,0.402 3.185,0.551 0.172,0.149 10 *a 1.446,1.047 1.446,0.489 1.446,0.489 3,0.489 false 1.507,1.095 1.507,0.489 false

Align the matchmarks on the No. 2 steering intermediate shaft assembly and steering column assembly.

Text in Illustration
*a Matchmark


b.

Install the No. 2 steering intermediate shaft assembly to the steering column assembly.


c.

Install the bolt.

Torque:
35 N*m (360 kgf*cm, 26 ft.*lbf)


Hide 3.INSTALL STEERING COLUMN ASSEMBLY

a.
C353570

Install the steering column assembly with the bolt and 2 nuts.

Torque:
Bolt : 36 N*m (370 kgf*cm, 26 ft.*lbf)
Nut : 25 N*m (255 kgf*cm, 18 ft.*lbf)


b.
C356279

Connect the 2 connectors to the power steering ECU assembly.


c.

Connect each connector and engage each wire harness clamp to the steering column assembly.


Hide 45260 4.CONNECT NO. 2 STEERING INTERMEDIATE SHAFT ASSEMBLY

a.
C136578E07
1.833,1.365 2.844,1.365 true 1.802,1.427 2.625,1.427 2.625,1.427 2.625,1.365 true 2.854,1.281 3.01,1.438 0.156,0.156 10 true *a

Align the matchmarks on the No. 2 steering intermediate shaft assembly and steering intermediate shaft assembly.

Text in Illustration
*a Matchmark


b.

Connect the No. 2 steering intermediate shaft assembly to the steering intermediate shaft assembly.


c.

Install the bolt.

Torque:
35 N*m (360 kgf*cm, 26 ft.*lbf)


Hide 45259A 5.INSTALL COLUMN HOLE COVER SILENCER SHEET

a.
C128486

Install the column hole cover silencer sheet with the 2 clips.


b.

Return the floor carpet to its original position.


Hide 87201F 6.INSTALL NO. 3 AIR DUCT SUB-ASSEMBLY

a.
C356268

Engage the 2 claws to install the No. 3 air duct sub-assembly.


b.

Install the clip.


Hide 73900 7.INSTALL DRIVER SIDE KNEE AIRBAG ASSEMBLY (w/ Driver Side Knee Airbag)

Hide 55432B 8.INSTALL INSTRUMENT PANEL FINISH PANEL LOWER (w/ Driver Side Knee Airbag)

HINT:

This is symmetrical to the LHD model (See page Vehicle Interior>INTERIOR PANEL>LOWER INSTRUMENT PANEL>INSTALLATION).


Hide 55432B 9.INSTALL INSTRUMENT PANEL FINISH PANEL LOWER (w/o Driver Side Knee Airbag)

HINT:

This is symmetrical to the LHD model (See page Vehicle Interior>INTERIOR PANEL>LOWER INSTRUMENT PANEL>INSTALLATION).


Hide 55606 10.INSTALL NO. 1 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY

HINT:

This is symmetrical to the LHD model (See page Vehicle Interior>INTERIOR PANEL>LOWER INSTRUMENT PANEL>INSTALLATION).


Hide 62111C 11.INSTALL COWL SIDE TRIM BOARD RH

HINT:
·

Perform the same procedure as for the LH side (See page Vehicle Interior>INTERIOR>ROOF HEADLINING>INSTALLATION).

·

This is symmetrical to the LHD model



Hide 67913B 12.INSTALL FRONT DOOR SCUFF PLATE RH

HINT:
·

Perform the same procedure as for the LH side (See page Vehicle Interior>INTERIOR PANEL>LOWER INSTRUMENT PANEL>INSTALLATION).

·

This is symmetrical to the LHD model



Hide 55446A 13.INSTALL NO. 1 SWITCH HOLE BASE

HINT:

This is symmetrical to the LHD model (See page Vehicle Interior>INTERIOR PANEL>LOWER INSTRUMENT PANEL>INSTALLATION).


Hide 55041B 14.INSTALL NO. 1 INSTRUMENT PANEL BOX DOOR SUB-ASSEMBLY

Hide 15.INSTALL CENTER INSTRUMENT CLUSTER FINISH PANEL ASSEMBLY

Hide 33504F 16.INSTALL SHIFT LEVER KNOB SUB-ASSEMBLY

Hide 17.INSTALL TURN SIGNAL SWITCH ASSEMBLY WITH SPIRAL CABLE

a.
C353569E02
2.781,0.625 2.781,0.229 2.781,0.229 1.375,0.229 true 2.552,0.552 1.802,0.552 true 1.635,0.458 1.823,0.646 0.188,0.188 10 false *a 1.208,0.146 1.396,0.333 0.188,0.188 10 false *b

Using pliers, expand the clamp.

Text in Illustration
*a Clamp
*b Claw


b.

While holding the clamp expanded, install the turn signal switch assembly with spiral cable to the steering column assembly and engage the claw.


c.

Return the clamp to its original position.


d.

Connect each connector to the turn signal switch assembly with spiral cable.


Hide 45286 18.INSTALL STEERING COLUMN COVER

a.
C353568

Engage the 3 claws, 4 clips, and 2 pins to install the steering column cover (upper side).


b.
C353567

Engage the 2 claws to install the steering column cover (lower side).


c.
C353564

Engage the 2 claws.


d.
C353565

Engage the claw.

HINT:

Press the area around the claw to engage it.



Hide 19.ALIGN FRONT WHEELS FACING STRAIGHT AHEAD

Hide 45100 21.INSTALL STEERING WHEEL ASSEMBLY

a.
C353562E01
1.888,0.536 0.534,0.536 false 1.888,0.777 0.745,0.777 0.745,0.777 0.745,0.536 false 0.302,0.433 0.507,0.613 0.205,0.180 10 *a

Align the matchmarks and install the steering wheel assembly onto the steering column assembly.

Text in Illustration
*a Matchmark


b.

Install the nut.

Torque:
50 N*m (510 kgf*cm, 37 ft.*lbf)


c.

Connect each connector to the spiral cable.


Hide 22.CHECK STEERING WHEEL CENTER POINT

Hide 24. TORQUE SENSOR ZERO POINT CALIBRATION