Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › VEHICLE STABILITY CONTROL SYSTEM › 2014.09–2016.05
RM24M0E _54 Brake _059583 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0292158 VEHICLE STABILITY CONTROL SYSTEM J

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  VEHICLE STABILITY CONTROL SYSTEM  ABS Warning Light Remains ON  


DESCRIPTION

The skid control ECU (brake actuator assembly) is connected to the combination meter assembly via CAN communication. If any of the following is detected, the ABS warning light remains on:

1.

The skid control ECU (brake actuator assembly) connector is disconnected from the skid control ECU (brake actuator assembly).

2.

There is a malfunction in the skid control ECU (brake actuator assembly) internal circuit.

3.

There is an open in the harness between the combination meter assembly and skid control ECU (brake actuator assembly).

4.

The ABS is defective.


HINT:

In some cases, the GTS cannot be used when the skid control ECU (brake actuator assembly) is abnormal.


WIRING DIAGRAM

C298669E04
4.25,3.229 5.177,3.438 0.927,0.208 10 false GAUGE NO. 1 4.354,4.146 5.052,4.354 0.698,0.208 10 false ABS NO. 2 4.458,3.865 4.656,4.073 0.198,0.208 10 false 1 4.854,3.865 5.052,4.104 0.198,0.24 10 false 2 5.823,2.948 6.083,3.156 0.26,0.208 10 false 28 6.125,3.063 6.448,3.271 0.323,0.208 10 false IG1 2.146,3.063 3.604,3.302 1.458,0.24 10 false from LH-IG Relay2 2.521,3.969 3.313,4.177 0.792,0.208 10 false from Battery 5.813,3.854 6.104,4.063 0.292,0.208 10 false 25 6.115,3.969 6.479,4.177 0.365,0.208 10 false +BS 6.115,4.865 6.604,5.073 0.49,0.208 10 false GND1 5.833,4.75 6.104,4.958 0.271,0.208 10 false 38 5.906,5.917 7.063,6.469 1.156,0.552 10 false Skid Control ECU (Brake Actuator Assembly) 5.583,5.917 5.917,6.125 0.333,0.208 10 false A35 2.76,6.385 5.042,6.625 2.281,0.24 10 false : CAN Communication Line 0.656,5.917 2.021,6.302 1.365,0.385 10 false Combination Meter Assembly 0.333,5.917 0.708,6.094 0.375,0.177 10 false G28 0.823,2.156 1.292,2.365 0.469,0.208 10 false CANH 0.844,1.188 1.271,1.396 0.427,0.208 10 false CANL 1.354,1 1.635,1.208 0.281,0.208 10 false 31 1.344,1.969 1.646,2.208 0.302,0.24 10 false 32 6.115,1.188 6.594,1.427 0.479,0.24 10 false CANL 6.115,2.167 6.625,2.375 0.51,0.208 10 false CANH 5.833,1.01 6.104,1.219 0.271,0.208 10 false 14 5.833,1.969 6.063,2.177 0.229,0.208 10 false 26

CAUTION / NOTICE / HINT

NOTICE:
·

When replacing the skid control ECU (brake actuator assembly), perform system variant learning and acceleration sensor zero point calibration (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>CALIBRATION).

·

Inspect the fuses for circuits related to this system before performing the following procedure.



PROCEDURE

1.CHECK CAN COMMUNICATION SYSTEM
a.

Check if CAN communication system DTCs are output (See page Power Source / Network>CAN COMMUNICATION>CAN COMMUNICATION SYSTEM>DIAGNOSIS SYSTEM).


Result:
Result Proceed to
DTCs are not output. A
DTCs are output. B



A

2.CHECK IF BRAKE ACTUATOR ASSEMBLY CONNECTOR IS SECURELY CONNECTED

B

2.CHECK IF BRAKE ACTUATOR ASSEMBLY CONNECTOR IS SECURELY CONNECTED
a.

Check if the skid control ECU (brake actuator assembly) connector is securely connected.

OK:

The connector is securely connected.




OK

3.CHECK BATTERY

NG

CONNECT CONNECTOR TO BRAKE ACTUATOR ASSEMBLY CORRECTLY

3.CHECK BATTERY
a.

Check the battery voltage.

Standard Voltage:

11 to 14 V




OK

4.CHECK HARNESS AND CONNECTOR (POWER SOURCE TERMINAL)

NG

REPAIR OR REPLACE CHARGING SYSTEM COMPONENT OR BATTERY

4.CHECK HARNESS AND CONNECTOR (POWER SOURCE TERMINAL)
a.
U189562E02
1.208,1.521 1.542,0.781 false 2.75,1.479 2.958,0.729 false 0.344,2.677 0.677,1.583 false 0.271,0.177 0.469,0.333 0.198,0.156 10 false *a 0.229,0.781 0.521,0.938 0.292,0.156 10 false A35 1.469,0.583 1.76,0.74 0.292,0.156 10 false IG1 0.177,2.698 0.469,2.854 0.292,0.156 10 false +BS 2.729,0.552 3.156,0.708 0.427,0.156 10 false GND1

Disconnect the A35 skid control ECU (brake actuator assembly) connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A35-25 (+BS) - Body ground Always 11 to 14 V
A35-25 (+BS) - A35-38 (GND1) Always 11 to 14 V
A35-28 (IG1) - Body ground Engine switch on (IG) 11 to 14 V
A35-28 (IG1) - A35-38 (GND1) Engine switch on (IG) 11 to 14 V


Text in Illustration
*a Front view of wire harness connector
(to Skid Control ECU (Brake Actuator Assembly))



OK

5.CHECK HARNESS AND CONNECTOR (GND1 TERMINAL)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (POWER SOURCE TERMINAL)

5.CHECK HARNESS AND CONNECTOR (GND1 TERMINAL)
a.
U189563E02
2.729,1.5 2.292,0.771 false 0.271,0.198 0.469,0.354 0.198,0.156 10 false *a 0.24,0.792 0.531,0.948 0.292,0.156 10 false A35 2.031,0.594 2.49,0.75 0.458,0.156 10 false GND1

Turn the engine switch off.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A35-38 (GND1) - Body ground Always Below 1 Ω


Text in Illustration
*a Front view of wire harness connector
(to Skid Control ECU (Brake Actuator Assembly))



OK

6.READ VALUE USING GTS (ABS WARNING LIGHT)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (GND1 CIRCUIT)

6.READ VALUE USING GTS (ABS WARNING LIGHT)
a.

Reconnect the A35 skid control ECU (brake actuator assembly) connector.


b.

Connect the GTS to the DLC3.


c.

Turn the engine switch on (IG).


d.

Select the Data List on the GTS (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>DATA LIST / ACTIVE TEST).

ABS/VSC/TRC
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
ABS Warning Light ABS warning light / ON or OFF ON: Warning light on
OFF: Warning light off
-


e.

Check the GTS display condition of the ABS warning light.

Result:
Result Proceed to
Display of the Data List remains ON. A
Display of the Data List remains OFF. B


HINT:

If troubleshooting has been carried out according to Problem Symptoms Table, refer back to the table and proceed to the next step before replacing parts (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>PROBLEM SYMPTOMS TABLE).




A

B