Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › VEHICLE STABILITY CONTROL SYSTEM › 2014.09–2016.05
RM24M0E _54 Brake _059583 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0292158 VEHICLE STABILITY CONTROL SYSTEM J

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  VEHICLE STABILITY CONTROL SYSTEM  TC and CG Terminal Circuit  


DESCRIPTION

Connecting terminals TC and CG of the DLC3 causes the ECU to display DTCs by blinking the ABS warning and slip indicator lights.

WIRING DIAGRAM

C367969E01
0.906,0.698 1.521,0.896 0.615,0.198 10 false CANL 1.417,0.51 1.729,0.708 0.313,0.198 10 false 49 0.885,1.385 1.5,1.583 0.615,0.198 10 false CANH 1.396,1.229 1.708,1.427 0.313,0.198 10 false 41 1.417,2.833 1.729,3.031 0.313,0.198 10 false 27 1.104,2.979 1.417,3.177 0.313,0.198 10 false TC 0.719,4.146 1.031,4.344 0.313,0.198 10 false A7 0.719,4.323 1.177,4.521 0.458,0.198 10 false ECM 2.74,3.719 4.448,3.917 1.708,0.198 10 false : CAN Communication Line 5.677,0.51 5.99,0.708 0.313,0.198 10 false 14 5.99,0.698 6.604,0.896 0.615,0.198 10 false CANL 5.969,1.406 6.583,1.604 0.615,0.198 10 false CANH 5.677,1.219 5.99,1.417 0.313,0.198 10 false 26 5.677,2.844 5.99,3.042 0.313,0.198 10 false 13 5.719,3.458 5.875,3.656 0.156,0.198 10 false 4 5.979,2.969 6.292,3.167 0.313,0.198 10 false TC 5.969,3.583 6.281,3.781 0.313,0.198 10 false CG 6.073,4.135 6.531,4.333 0.458,0.198 10 false G15 6.083,4.313 6.698,4.51 0.615,0.198 10 false DLC3 5.563,1.833 6.021,2.031 0.458,0.198 10 false A35 5.552,2.01 7.094,2.385 1.542,0.375 10 false Skid Control ECU (Brake Actuator Assembly)

CAUTION / NOTICE / HINT

NOTICE:

When replacing the skid control ECU (brake actuator assembly), perform system variant learning and acceleration sensor zero point calibration (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>CALIBRATION).


HINT:

When the indicator lights continue to blink, a ground short in the wiring of terminal TC of the DLC3 or an internal ground short in one or more ECUs is suspected.


PROCEDURE

1.CHECK CAN COMMUNICATION SYSTEM
a.

Check if CAN communication system DTCs are output (See page Power Source / Network>CAN COMMUNICATION>CAN COMMUNICATION SYSTEM>DIAGNOSIS SYSTEM).

Result:
Result Proceed to
DTCs are not output. A
DTCs are output. B




A

2.INSPECT DLC3

B

2.INSPECT DLC3
a.
U189646E02
1.604,1.927 1.135,0.979 false 2.729,1.063 1.844,2.365 false 0.26,0.25 0.448,0.417 0.188,0.167 10 false *a 1.01,0.781 1.25,0.948 0.24,0.167 10 false CG 0.271,1.042 0.594,1.188 0.323,0.146 10 false G15 2.75,0.885 2.99,1.052 0.24,0.167 10 false TC

Turn the engine switch on (IG).


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
G15-13 (TC) - G15-4 (CG) Engine switch on (IG) 11 to 14 V


Text in Illustration
*a Front view of DLC3



OK

3.REPLACE ECM

NG

4.CHECK HARNESS AND CONNECTOR (TC of DLC3 - ECM)
3.REPLACE ECM
a.
U189646E02
1.604,1.927 1.135,0.979 false 2.729,1.063 1.844,2.365 false 0.26,0.25 0.448,0.417 0.188,0.167 10 false *a 1.01,0.781 1.25,0.948 0.24,0.167 10 false CG 0.271,1.042 0.594,1.188 0.323,0.146 10 false G15 2.75,0.885 2.99,1.052 0.24,0.167 10 false TC

Turn the engine switch off.



c.

Using SST, connect terminals TC and CG of the DLC3.


SST
09843-18040  

d.

Check that the ABS warning and slip indicator lights are blinking.

OK:

The ABS warning and slip indicator lights are blinking.


Text in Illustration
*a Front view of DLC3

HINT:

If troubleshooting has been carried out according to Problem Symptoms Table, refer back to the table and proceed to the next step before replacing parts (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>PROBLEM SYMPTOMS TABLE).




OK

END

NG

4.CHECK HARNESS AND CONNECTOR (TC of DLC3 - ECM)
a.

Turn the engine switch off.


b.

Disconnect the A7 ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G15-13 (TC) - A7-27 (TC) Always Below 1 Ω
G15-13 (TC) or A7-27 (TC) - Body ground Always 10 kΩ or higher




OK

5.CHECK HARNESS AND CONNECTOR (CG of DLC3 - BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.CHECK HARNESS AND CONNECTOR (CG of DLC3 - BODY GROUND)
a.
U189647E01
0.263,0.249 0.446,0.419 0.184,0.170 10 *a 2.308,0.794 2.547,0.963 0.239,0.170 10 CG 0.27,1.039 0.594,1.190 0.324,0.151 10 G15 1.669,1.923 2.396,0.979 false

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G15-4 (CG) - Body ground Always Below 1 Ω


Text in Illustration
*a Front view of DLC3



OK

6.REPLACE ECM

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.REPLACE ECM
a.
U189646E02
1.604,1.927 1.135,0.979 false 2.729,1.063 1.844,2.365 false 0.26,0.25 0.448,0.417 0.188,0.167 10 false *a 1.01,0.781 1.25,0.948 0.24,0.167 10 false CG 0.271,1.042 0.594,1.188 0.323,0.146 10 false G15 2.75,0.885 2.99,1.052 0.24,0.167 10 false TC

Replace the ECM (See page Engine / Hybrid System>2AZ-FE ENGINE CONTROL>ECM>REMOVAL for 2AZ-FE, Engine / Hybrid System>2GR-FE ENGINE CONTROL>ECM>REMOVAL for 2GR-FE).


b.

Using SST, connect terminals TC and CG of the DLC3.


SST
09843-18040  

c.

Check that the ABS warning and slip indicator lights are blinking.

OK:

The ABS warning and slip indicator lights are blinking.


Text in Illustration
*a Front view of DLC3

HINT:

If troubleshooting has been carried out according to Problem Symptoms Table, refer back to the table and proceed to the next step before replacing parts (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>PROBLEM SYMPTOMS TABLE).




OK

END

NG