The speed sensors detect the wheel speeds and send appropriate signals to the skid control ECU.
Speed sensor rotors have rows of alternating N and S magnetic poles, and their magnetic fields change as the rotors turn.
The speed sensors detect those magnetic changes and send pulse signals to the skid control ECU. The ECU monitors the wheel speeds through these pulse signals to control the ABS control system.
DTCs C1271/71, C1272/72, C1275/75 and C1276/76 can be deleted when the speed sensor sends a vehicle speed signal or the test mode ends. DTCs C1271/71, C1272/72, C1275/75/75 and C1276/76 are output only in the test mode.
| DTC No. | DTC Detection Condition | Trouble Area |
|---|---|---|
| C0200/31
C0205/32 |
When one of following conditions is met:
1.
Vehicle speed is more than 40 km/h (25 mph) and pulses are not input for 0.01 second. 2.
After the initial start or restart and when the vehicle speed has reached 12 km/h (7 mph), the wheel speed of 0 km/h (0 mph) is detected. 3.
After the initial start or restart and when the vehicle speed has reached 18 km/h (11 mph), the front wheel speed of 0 km/h (0 mph) is detected. |
·
Front speed sensor ·
Front speed sensor circuit ·
Sensor installation ·
Foreign matter on sensor rotor |
| C1271/71
C1272/72 |
Detected only during test mode. | ·
Front speed sensor ·
Front speed sensor circuit ·
Sensor installation ·
Foreign matter on sensor rotor |
| C1275/75
C1276/76 |
Detected only during test mode. | ·
Front speed sensor ·
Front speed sensor circuit ·
Sensor installation |
| C1330/35
C1331/36 |
Abnormality in the resistance value of each speed sensor is detected. | ·
Front speed sensor RH and/or LH ·
Front speed sensor circuit RH and/or LH ·
Sensor installation ·
ABS and TRACTION actuator |
DTCs C0200/31 and C1330/35 relate to the front speed sensor RH.
DTCs C0205/32 and C1331/36 relate to the front speed sensor LH.
Check the speed sensor signal in test mode after cleaning or replacement (see page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>TEST MODE PROCEDURE).
Using the Data List of the intelligent tester, check for any momentary interruption in the wire harness and connector corresponding to a DTC (see page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>CHECK FOR INTERMITTENT PROBLEMS).
| Tester Display | Measurement Item/Range | Normal Condition | Diagnostic Note |
|---|---|---|---|
| FR Speed Open | FR speed sensor open detection / ERROR or NORMAL | ERROR: Momentary interruption
NORMAL: Normal |
- |
| FL Speed Open | FL speed sensor open detection / ERROR or NORMAL | ERROR: Momentary interruption
NORMAL: Normal |
- |
There are no momentary interruptions.
Perform the above inspection before removing the sensor and connector.
OK
NG
Check the Data List for proper functioning of the front speed sensor.
| Tester Display | Measurement Item/Range | Normal Condition | Diagnostic Note |
|---|---|---|---|
| FR Wheel Speed | Wheel speed sensor (FR) reading : min.: 0 km/h (0 mph), max.: 326 km/h (202.8 mph) | Similar to speed indicated on speedometer | - |
| FL Wheel Speed | Wheel speed sensor (FL) reading : min.: 0 km/h (0 mph), max.: 326 km/h (202.8 mph) | Similar to speed indicated on speedometer | - |
There is almost no difference between actual wheel speed and displayed speed value.
There is a tolerance of +-10% in the speedometer indication.
OK
NG
Perform a TEST MODE inspection and check for DTCs (see page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>TEST MODE PROCEDURE).
No DTC output.
OK
NG
Clear the DTC(s) (see page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>DTC CHECK / CLEAR).
Start the engine.
Drive the vehicle at a speed of 20 km/h (12 mph) or more for at least 60 seconds.
Check if the same DTC(s) is output (see page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>DTC CHECK / CLEAR).
| Result | Proceed to |
|---|---|
| DTC is not output | A |
| DTC is output | B |
A
B
Check that the speed sensor installation bolt is tightened properly.
The installation bolt is tightened properly, and there is no clearance between the sensor and front steering knuckle.
8.5 N*m (87 kgf*cm, 75 in.*lbf)
If the installation portion of the sensor is dirty, clean it and reinstall the sensor.
Check the speed sensor after the speed sensor replacement (see page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>TEST MODE PROCEDURE).
OK
NG
Remove the front speed sensor.
Check the sensor tip.
No scratches or foreign matter on the sensor tip.
Check the speed sensor signal after the speed sensor clearing or replacement (see page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>TEST MODE PROCEDURE).
OK
NG
Disconnect the A9 ECU connector.
Disconnect the A5 and A20 sensor connectors.
Measure the resistance of the wire harness side connectors.
| Tester Connection | Specified Condition |
|---|---|
| A9-26 (FL+) - A5-2 | Below 1 Ω |
| A9-5 (FL-) - A5-1 | Below 1 Ω |
| A9-26 (FL+) - Body ground | 10 kΩ or higher |
| A9-5 (FL-) - Body ground | 10 kΩ or higher |
| Tester Connection | Specified Condition |
|---|---|
| A9-9 (FR+) - A20-2 | Below 1 Ω |
| A9-10 (FR-) - A20-1 | Below 1 Ω |
| A9-9 (FR+) - Body ground | 10 kΩ or higher |
| A9-10 (FR-) - Body ground | 10 kΩ or higher |
OK
NG
Clear the DTC(s) (see page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>DTC CHECK / CLEAR).
Start the engine.
Drive the vehicle at a speed of 20 km/h (12 mph) or more for at least 60 seconds.
Check if the same DTC(s) is output (see page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>DTC CHECK / CLEAR).
| Result | Proceed to |
|---|---|
| DTC is output | A |
| DTC is not output | B |
A
B
Replace the front speed sensor (see page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>FRONT SPEED SENSOR>REMOVAL).
NEXT
Clear the DTC(s) (see page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>DTC CHECK / CLEAR).
Start the engine.
Drive the vehicle at a speed of 20 km/h (12 mph) or more for at least 60 seconds.
Check if the same DTC(s) is output (see page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>DTC CHECK / CLEAR).
| Result | Proceed to |
|---|---|
| DTC is output (for 2AZ-FE) | A |
| DTC is output (for 2GR-FE) | B |
| DTC is not output | C |
A
B
C