Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › VEHICLE STABILITY CONTROL SYSTEM › 2014.09–2016.05
RM24M0E _54 Brake _059583 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0292158 VEHICLE STABILITY CONTROL SYSTEM J

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  VEHICLE STABILITY CONTROL SYSTEM  VSC OFF Switch Circuit  


DESCRIPTION

The skid control ECU (brake actuator assembly) is connected to the combination meter assembly via CAN communication.

Pressing the VSC OFF switch turns off TRC operation, and pressing and holding this switch turns off TRC and VSC operation. If TRC and VSC operations are turned off, the TRC OFF indicator light and the VSC OFF indicator light will come on.

WIRING DIAGRAM

C360136E02
1.375,0.76 1.688,0.958 0.313,0.198 10 false 31 0.896,0.917 1.313,1.115 0.417,0.198 10 false CANL 0.885,1.74 1.302,1.938 0.417,0.198 10 false CANH 1.375,1.563 1.688,1.76 0.313,0.198 10 false 32 5.688,0.75 6,0.948 0.313,0.198 10 false 14 5.708,1.573 6.021,1.771 0.313,0.198 10 false 26 5.958,0.927 6.375,1.125 0.417,0.198 10 false CANL 5.958,1.74 6.375,1.938 0.417,0.198 10 false CANH 5.958,2.885 6.375,3.083 0.417,0.198 10 false CSW 5.781,2.771 6.094,2.969 0.313,0.198 10 false 9 4.844,2.771 5.156,2.969 0.313,0.198 10 false 6 3.802,2.781 4.115,2.979 0.313,0.198 10 false 3 4.646,3.01 4.958,3.208 0.313,0.198 10 false + 3.969,3.01 4.281,3.208 0.313,0.198 10 false E 5.49,3.865 5.906,4.063 0.417,0.198 10 false A35 3.833,3.25 4.25,3.448 0.417,0.198 10 false G101 0.26,3.927 0.677,4.125 0.417,0.198 10 false G28 0.26,4.094 1.563,4.49 1.302,0.396 10 false Combination Meter Assembly 5.479,4.052 7.042,4.49 1.563,0.438 10 false Skid Control ECU (Brake Actuator Assembly) 3.833,3.427 5.396,3.865 1.563,0.438 10 false VSC OFF Switch 2.896,4.344 4.74,4.563 1.844,0.219 10 false : CAN Communication Line

CAUTION / NOTICE / HINT

NOTICE:

When replacing the skid control ECU (brake actuator assembly), perform system variant learning and acceleration sensor zero point calibration (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>CALIBRATION).


PROCEDURE

1.CHECK CAN COMMUNICATION SYSTEM
a.

Check if CAN communication system DTCs are output (See page Power Source / Network>CAN COMMUNICATION>CAN COMMUNICATION SYSTEM>DIAGNOSIS SYSTEM).

Result:
Result Proceed to
DTCs are not output. A
DTCs are output. B




A

2.CHECK IF BRAKE ACTUATOR ASSEMBLY CONNECTOR IS SECURELY CONNECTED

B

2.CHECK IF BRAKE ACTUATOR ASSEMBLY CONNECTOR IS SECURELY CONNECTED
a.

Check if the skid control ECU (brake actuator assembly) connector is securely connected.

OK:

The connector is securely connected.




OK

3.READ VALUE USING GTS (TRC/VSC OFF MODE)

NG

CONNECT CONNECTOR TO BRAKE ACTUATOR ASSEMBLY CORRECTLY

3.READ VALUE USING GTS (TRC/VSC OFF MODE)
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG).


c.

Select the Data List using the GTS (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>DATA LIST / ACTIVE TEST).

ABS/VSC/TRC
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
TRC/VSC Off Mode TRC/VSC off mode / Normal, TRC OFF, Unknown or VSC OFF Normal: Normal mode
TRC OFF: TRC off mode
Unknown: Unspecified
VSC OFF: VSC off mode
-


d.

Check the indicator light and mode condition on the GTS changes according to VSC OFF switch operation.

Standard:
Switch Operation Mode Condition Display TRC OFF Indicator Light VSC OFF Indicator Light
Not pressed Normal Does not come on Does not come on
Pressing the VSC OFF switch TRC OFF Comes on Does not come on
Pressing and holding the VSC OFF switch VSC OFF Comes on Comes on


Result:
Result Proceed to
Indicator light and mode condition display do not change. A
Mode condition display is normal, but indicator light does not change. B
Indicator light and mode condition display is normal. C




A

4.PERFORM ACTIVE TEST USING GTS (TRC OFF INDICATOR LIGHT AND VSC OFF INDICATOR LIGHT)

B

C

4.PERFORM ACTIVE TEST USING GTS (TRC OFF INDICATOR LIGHT AND VSC OFF INDICATOR LIGHT)
a.

Select the Active Test on the GTS (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>DATA LIST / ACTIVE TEST).

ABS/VSC/TRC
Tester Display Test Part Control Range Diagnostic Note
TRC(TRAC) OFF Indicator Light TRC OFF indicator light Indicator light ON/OFF Observed combination meter assembly
VSC OFF Indicator Light VSC OFF indicator light Indicator light ON/OFF Observed combination meter assembly


b.

Check the TRC OFF indicator light and VSC OFF indicator light in the combination meter assembly turn on or off in accordance with GTS operation.

OK:

The TRC OFF indicator light and VSC OFF indicator light turn on or off in accordance with GTS operation.




OK

5.INSPECT VSC OFF SWITCH

NG

7.INSPECT COMBINATION METER ASSEMBLY
5.INSPECT VSC OFF SWITCH
a.
C239020E05
0.171,0.138 0.444,0.377 0.274,0.239 10 *a 1.898,2.028 2.474,2.87 false 1.527,2.028 0.952,2.87 false 2.431,2.883 2.559,3.046 0.128,0.163 10 E 0.849,2.883 0.978,3.046 0.128,0.163 10 +

Turn the engine switch off.


b.

Disconnect the G101 VSC OFF switch connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
6 (+) - 3 (E) Switch is pushed Below 1 Ω
6 (+) - 3 (E) Switch is not pushed 10 kΩ or higher


Text in Illustration
*a Component without harness connected
(VSC OFF Switch)



OK

6.CHECK HARNESS AND CONNECTOR (BRAKE ACTUATOR ASSEMBLY - VSC OFF SWITCH)

NG

6.CHECK HARNESS AND CONNECTOR (BRAKE ACTUATOR ASSEMBLY - VSC OFF SWITCH)
a.

Disconnect the A35 skid control ECU (brake actuator assembly) connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A35-9 (CSW) - G101-6 (+) Always Below 1 Ω
A35-9 (CSW) or G101-6 (+) - Body ground Always 10 kΩ or higher
G101-3 (E) - Body ground Always Below 1 Ω


HINT:

If troubleshooting has been carried out according to Problem Symptoms Table, refer back to the table and proceed to the next step before replacing parts (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>PROBLEM SYMPTOMS TABLE).




OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

7.INSPECT COMBINATION METER ASSEMBLY
a.

Turn the engine switch off.


b.

Perform an Active Test of the combination meter assembly using the GTS (See page Vehicle Interior>METER / GAUGE / DISPLAY>METER / GAUGE SYSTEM>DATA LIST / ACTIVE TEST).


c.

Check the combination meter assembly.

OK:

The TRC OFF indicator light and VSC OFF indicator light turn on or off in accordance with GTS operation.


HINT:

If troubleshooting has been carried out according to Problem Symptoms Table, refer back to the table and proceed to the next step before replacing parts (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>PROBLEM SYMPTOMS TABLE).




OK

NG