Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › VEHICLE STABILITY CONTROL SYSTEM › from 2016.05
RM24M0E _54 Brake _059583 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0292158 VEHICLE STABILITY CONTROL SYSTEM C

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  VEHICLE STABILITY CONTROL SYSTEM  C1249  Open in Stop Light Switch Circuit  


DESCRIPTION

The skid control ECU (brake actuator assembly) receives stop light switch assembly signals and uses them to determine whether or not the brakes are applied. DTCs may be stored if either of the following occurs:

·

Stop light switch assembly stuck on malfunction.

·

The accelerator and brake pedals are depressed simultaneously.*


HINT:

*: The skid control ECU (brake actuator assembly) may store this DTC upon judging that a stuck on malfunction has occurred when the accelerator pedal and brake pedal are depressed simultaneously. However, this does not indicate a malfunction.


DTC No. Detection Item DTC Detection Condition Trouble Area
C1249 Open in Stop Light Switch Circuit The vehicle speed is 10 km/h (6 mph) or more, the accelerator pedal is depressed, the master cylinder pressure is 0.5 MPa (5.09 kgf/cm2, 72 psi) or less, and the stop light switch assembly is on for 60 seconds or more.
·

Wire harness or connector

·

Stop light switch assembly

·

Skid control ECU (brake actuator assembly)



WIRING DIAGRAM

C359814E01
0.169,1.088 1.057,1.318 0.887,0.230 10 from Battery 1.687,1.28 2.167,1.538 0.480,0.258 10 STOP 3.462,1.023 3.682,1.253 0.221,0.230 10 2 3.462,1.317 3.682,1.547 0.221,0.230 10 3 2.065,1.023 2.286,1.253 0.221,0.230 10 2 2.397,1.023 2.696,1.234 0.299,0.211 10 1 1.594,1.023 1.893,1.234 0.299,0.211 10 1 2.105,1.941 4.312,2.152 2.207,0.211 10 Stop Light Switch Assembly 2.119,1.773 2.548,1.984 0.429,0.211 10 A37 0.478,4.479 1.995,4.672 1.517,0.193 10 : Open Detection Area 5.965,1.116 6.399,1.328 0.434,0.211 10 STP 5.694,0.99 6.035,1.230 0.341,0.239 10 30 5.951,2.844 6.505,3.056 0.554,0.211 10 GND1 5.699,2.746 5.966,2.976 0.267,0.230 10 38 1.762,2.835 3.084,3.065 1.323,0.230 10 to Stop Light Circuit 5.512,3.937 7.087,4.297 1.575,0.360 10 Skid Control ECU (Brake Actuator Assembly) 5.517,3.774 5.913,4.013 0.397,0.239 10 A35 3.06,1.112 3.494,1.323 0.434,0.211 10 OUT 2.594,1.112 3.028,1.323 0.434,0.211 10 +B 3.046,1.425 3.480,1.636 0.434,0.211 10 GND

CAUTION / NOTICE / HINT

NOTICE:
·

When replacing the skid control ECU (brake actuator assembly), perform system variant learning and acceleration sensor zero point calibration (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>CALIBRATION).

·

Inspect the fuses for circuits related to this system before performing the following procedure.



PROCEDURE

1.CHECK ACCELERATOR PEDAL AND BRAKE PEDAL OPERATION
a.

Interview the customer to check if the pedals were depressed simultaneously while driving or braking.

OK:

The pedals were not depressed simultaneously.


HINT:

The skid control ECU (brake actuator assembly) may store this DTC upon judging that a stuck on malfunction has occurred when the accelerator pedal and brake pedal are depressed simultaneously.

If the pedals were depressed simultaneously, clear the DTC because it is not a malfunction.




OK

2.CHECK STOP LIGHT OPERATION

NG

CLEAR DTC

2.CHECK STOP LIGHT OPERATION
a.

Check that the stop lights come on when the brake pedal is depressed, and go off when the brake pedal is released.

OK:
Condition Illumination Condition
Brake pedal depressed. On
Brake pedal released. Off




OK

3.READ VALUE USING GTS (STOP LIGHT SWITCH ASSEMBLY)

NG

6.INSPECT STOP LIGHT SWITCH ASSEMBLY
3.READ VALUE USING GTS (STOP LIGHT SWITCH ASSEMBLY)
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG).


c.

Select the Data List using the GTS (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>DATA LIST / ACTIVE TEST).

ABS/VSC/TRC
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
Stop Light SW Stop light switch assembly / ON or OFF ON: Brake pedal depressed
OFF: Brake pedal released
-


d.

Check that the stop light switch assembly display observed on the GTS changes according to brake pedal operation.

OK:

The GTS displays ON or OFF according to brake pedal operation.




OK

4.RECONFIRM DTC

NG

5.CHECK HARNESS AND CONNECTOR (STP TERMINAL)
4.RECONFIRM DTC
a.

Turn the engine switch off.



c.

Turn the engine switch off.


d.

Start the engine.


e.

Drive the vehicle and depress the brake pedal several times to test the stop light circuit.


f.

Check if the same DTC is output (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>DTC CHECK / CLEAR).

Result:
Result Proceed to
DTC C1249 is not output. A
DTC C1249 is output. B


HINT:

If troubleshooting has been carried out according to Problem Symptoms Table, refer back to the table and proceed to the next step before replacing parts (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>PROBLEM SYMPTOMS TABLE).




A

B

5.CHECK HARNESS AND CONNECTOR (STP TERMINAL)
a.
U189564E02
1.51,1.531 1.74,0.74 false 0.271,0.198 0.469,0.354 0.198,0.156 10 false *a 0.25,0.781 0.542,0.938 0.292,0.156 10 false A35 1.75,0.573 2.042,0.729 0.292,0.156 10 false STP

Turn the engine switch off.


b.

Make sure that there is no looseness at the locking part and the connecting part of the connector.


c.

Disconnect the A35 skid control ECU (brake actuator assembly) connector.


d.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A35-30 (STP) - Body ground Stop light switch assembly ON (Brake pedal depressed) 11 to 14 V*
A35-30 (STP) - Body ground Stop light switch assembly OFF (Brake pedal released) Below 1.5 V


Text in Illustration
*a Front view of wire harness connector
(to Skid Control ECU (Brake Actuator Assembly))

HINT:
·

*: The standard voltage value varies depending on the +BS terminal voltage value. The standard voltage is 85% of the +BS terminal voltage.

·

If troubleshooting has been carried out according to Problem Symptoms Table, refer back to the table and proceed to the next step before replacing parts (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>PROBLEM SYMPTOMS TABLE).





OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (STP CIRCUIT)

6.INSPECT STOP LIGHT SWITCH ASSEMBLY
a.

Check the stop light switch assembly (See page Vehicle Interior>LIGHTING>STOP LIGHT SWITCH>ON-VEHICLE INSPECTION).

OK:

The stop light switch assembly is normal.




OK

7.CHECK HARNESS AND CONNECTOR (STP TERMINAL)

NG

REPLACE STOP LIGHT SWITCH ASSEMBLY

7.CHECK HARNESS AND CONNECTOR (STP TERMINAL)
a.
U189564E02
1.51,1.531 1.74,0.74 false 0.271,0.198 0.469,0.354 0.198,0.156 10 false *a 0.25,0.781 0.542,0.938 0.292,0.156 10 false A35 1.75,0.573 2.042,0.729 0.292,0.156 10 false STP

Reconnect the A37 stop light switch assembly connector.


b.

Make sure that there is no looseness at the locking part and the connecting part of the connector.


c.

Disconnect the A35 skid control ECU (brake actuator assembly) connector.


d.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A35-30 (STP) - Body ground Stop light switch assembly ON (Brake pedal depressed) 11 to 14 V*
A35-30 (STP) - Body ground Stop light switch assembly OFF (Brake pedal released) Below 1.5 V


Text in Illustration
*a Front view of wire harness connector
(to Skid Control ECU (Brake Actuator Assembly))

HINT:

*: The standard voltage value varies depending on the +BS terminal voltage value. The standard voltage is 85% of the +BS terminal voltage.




OK

8.RECONFIRM DTC

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (STP CIRCUIT)

8.RECONFIRM DTC
a.

Reconnect the A35 skid control ECU (brake actuator assembly) connector.



c.

Turn the engine switch off.


d.

Start the engine.


e.

Drive the vehicle and depress the brake pedal several times to test the stop light circuit.


f.

Check if the same DTC is output (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>DTC CHECK / CLEAR).

Result:
Result Proceed to
DTC C1249 is not output. A
DTC C1249 is output. B


HINT:
·

If the lighting system is normal but the DTC is still output, replace the skid control ECU (brake actuator assembly) (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>BRAKE ACTUATOR(w/ VSC)>REMOVAL).

·

If troubleshooting has been carried out according to Problem Symptoms Table, refer back to the table and proceed to the next step before replacing parts (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>PROBLEM SYMPTOMS TABLE).





A

B