Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › VEHICLE STABILITY CONTROL SYSTEM › 2013.04–2014.09
RM24M0E _54 Brake _059583 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0292158 VEHICLE STABILITY CONTROL SYSTEM C

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  VEHICLE STABILITY CONTROL SYSTEM  C1439/31  Steering Angle Sensor Initialization Incomplete  C1445/31  Vehicle Driven with Steering Angle Sensor not Initialized  


DESCRIPTION

The skid control ECU acquires the steering angle sensor zero point every time the engine switch is turned on (IG) and the vehicle is driven at 15 km/h (9 mph) or more for approximately 30 seconds. The ECU also stores previous zero points.

Warning of the steering angle sensor zero point malfunction will be canceled by turning the engine switch off.

DTC No. DTC Detection Condition Trouble Area
C1439/31 After the steering angle sensor zero point calibration is cleared due to, for example, fluctuations in the power source, the steering angle sensor zero point calibration cannot be obtained for 120 seconds of continuous driving.
·

Steering angle sensor

·

Yaw rate sensor


C1445/31 Steering angle sensor zero point calibration cannot be obtained when the vehicle is driven without a record of steering angle sensor zero point calibration at a speed of 15 km/h (9 mph) or more for 120 seconds or more without the brake pedal being depressed.
·

Steering angle sensor

·

Yaw rate sensor



CAUTION / NOTICE / HINT

NOTICE:

Before proceeding with the inspection, explain to the customer that the output DTC is related to temporary loss of the steering angle zero point calibration, such as when the power source voltage drops when the battery is removed, and confirm that this condition occurred.


HINT:
·

When U0073/94, U0123/62 and/or U0126/63 is output together with C1439/31 and/or C1445/31, inspect and repair the trouble areas indicated by U0073/94, U0123/62 and/or U0126/63 first (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>U0073/94).

·

When the speed sensor or the yaw rate sensor has trouble, DTCs for the steering angle sensor may be output even when the steering angle sensor is normal. When DTCs for the speed sensor or yaw rate sensor are output together with other DTCs for the steering angle sensor, inspect and repair the speed sensor and yaw rate sensor first, and then inspect and repair the steering angle sensor.



PROCEDURE

1.CHECK DTC

b.

Turn the engine switch off.


c.

Turn the engine switch on (IG) again and check that no CAN communication system DTCs are output (See page Power Source / Network>CAN COMMUNICATION>CAN COMMUNICATION SYSTEM>DIAGNOSIS SYSTEM).


d.

Drive the vehicle and turn the steering wheel to the right and left at a speed of 15 km/h (9 mph) and check that no speed sensor, steering angle sensor and yaw rate sensor DTCs are output (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>DTC CHECK / CLEAR).

Result:
Result Proceed to
DTCs C1439/31 and/or C1445/31 are output A
CAN communication system DTC is output B
Speed sensor, steering angle sensor and/or yaw rate sensor DTC is output C
DTCs are not output D


HINT:
·

If there is a malfunction in the speed sensor or the yaw rate sensor, an abnormal value may be output although the steering angle sensor is normal.

·

If the speed sensor and the yaw rate sensor DTCs are output simultaneously, repair the sensors and inspect the steering angle sensor.

·

If the same DTC C1439/31 and/or C1445/31 is not output again, the DTC may have been stored due to a temporary loss of the steering angle zero point calibration, such as when the power source voltage drops.





A

2.CHECK STEERING ANGLE SENSOR ZERO POINT CALIBRATION

B

C

D

2.CHECK STEERING ANGLE SENSOR ZERO POINT CALIBRATION
a.

Drive the vehicle straight ahead at 15 km/h (9 mph) or more for at least 30 seconds.


b.

Check that the centered position of the steering wheel is correctly set while driving straight ahead.

HINT:

If front wheel alignment and steering position are adjusted as a result of an off-centered position of the steering wheel, acquire yaw rate sensor zero point again after the adjustments are completed.


OK:

The centered position of the steering wheel is correctly set.




OK

3.RECONFIRM DTC

NG

ADJUST FRONT WHEEL ALIGNMENT OR STEERING POSITION

3.RECONFIRM DTC

b.

Start the engine.


c.

Drive the vehicle and turn the steering wheel to the right and left at the speed of 15 km/h (9 mph) or more for at least 120 seconds.


d.

Check if the same DTC is recorded (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>DTC CHECK / CLEAR).

Result:
Result Proceed to
DTCs are not output A
Steering angle sensor and/or yaw rate sensor DTC is output B


HINT:

If the same DTC C1439/31 and/or C1445/31 is not output again, the DTC may have been stored due to a temporary loss of the steering angle zero point calibration, such as when the power source voltage drops.




A

END

B